Every printable part.

Two alternative lower hook-holder geometries for the BMW accessory rear roller sunshade: an original-dimension version and a tighter-fit version tested in an early 1985 car. BMW references include discontinued white accessory hook 82129413177 and anthracite holder 51461905393, which supersedes 51461887130. E28/E30 body, production date, color and accessory installation vary; compare the no-screw-hole mounting style before use.

Fits 3 Series · E30 · 5 Series · E28

Replacement manual shifter-boot retaining frame for BMW E28 and E24 interiors. The creator measured an E28, fitted the design in the car and recommends PETG because PLA prototypes softened in cabin heat. The test car has a short shifter; correct worn or misadjusted linkage rather than relying on this frame to solve reverse-gear interference.

Fits 5 Series · E28 · 6 Series · E24

Replacement rotating knob/head for the manual sunroof crank of a BMW E28. The creator printed the part in PLA; PETG or ABS is preferable for a hot cabin. BMW catalogs supply the knob only with the complete crank handle, so no parent-assembly number is assigned. Confirm crank-pin diameter, trim color and production-date variation before fitting.

Fits 5 Series · E28

Replacement plastic retaining clip for the classic 14-inch steel wheel cover used on early BMW E28 cars. BMW catalogs identify the clip as 36131125740, used with wheel cover 36131125718 through September 1984; it is discontinued with no cataloged supersession. Verify the wheel-cover style and production date before use, and inspect every clip for secure retention.

Fits 5 Series · E28

Adjustable clutch-pedal stop body for manual-transmission BMW E28 and other listed classic BMW chassis. Assembly requires an M10 screw, two M10 nuts, a 40 mm washer and a genuine-style rubber cap. Adjust only far enough to remove excess pedal travel while preserving complete clutch disengagement, then lock the nuts securely and re-check operation before driving.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +4

Front and rear spacer geometry with locating rod for installing a Musway ME462 coaxial speaker in a BMW E28 sedan. The creator reports that the adapter set fits perfectly. This is specific to the stated speaker footprint; compare the mounting pattern, depth and trim clearance before printing for another driver.

Fits 5 Series · E28

Spacer and washer for fitting an upgraded 4×6-inch front speaker in a BMW E28 while retaining the original speaker cover. The creator confirms that the hood-release lever still clears the speaker and specifies longer #8×1.25-inch oval-head screws with #6-32 speed nuts. Check speaker depth and fastener clearance before final assembly.

Fits 5 Series · E28

Three-piece replacement bracket set for the BMW E28 front lower valance: left, center and right. The creator states that the parts fit in the stock locations and replaces factory brackets that commonly break or go missing. Use a UV- and heat-resistant engineering material, verify the valance variant and compare the mounting-hole geometry before fitting.

Fits 5 Series · E28

Replacement center retaining clip for the sun visor of a BMW E12 520. The creator physically fitted the part and recommends PETG, ASA, ABS or another cabin-heat-resistant material; PLA can deform in summer. BMW catalogs identify the equivalent ivory holder as 51161870863, superseding 51161820684; the photographed black print is a user-selected reproduction color, not an OEM color claim. Production date and trim variants can differ, so compare the two-hole base and visor-rod diameter before fitting.

Fits 5 Series · E12

Vent support for a Quad Lock phone interface, physically demonstrated on the right-hand-drive driver's-side center vent shared by the creator-listed BMW F30, F31 and F32. Fitment is limited to those bodies and RHD placement; F33/F36 and LHD fitment are not inferred. Use cabin-heat-resistant material, tighten without damaging the vent, and verify full vent, display, control and sightline clearance before driving.

Fits 3 Series · F30 / F31 / F34 / F80 · 4 Series · F32 / F33 / F36 / F82 / F83

Upper and lower storage trays with cutting templates for the F32/F33 center-console cavity after removal of the original phone cradle. The creator physically demonstrates both the shallow installation and the optional deeper cut-out; the cutting templates are retained as functional parts of the set. Use cabin-heat-resistant material, protect wiring before any cutting, deburr the opening, and verify secure fit and unobstructed console operation.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Three-piece detachable Qi charging stand physically demonstrated in the center cup holder of a BMW F32. It uses a user-supplied silicone Qi charging pad and routes its USB cable through the cup base; other chassis fitments are not inferred. Use cabin-heat-resistant material, electrically sound charging hardware and protected cable routing, and verify secure retention, cooling and unobstructed controls before driving.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Replacement clip and glue-in double-stud repair for broken F33 Convertible roof-frame moulding retainers, designed on and physically demonstrated with a 435i F33. The BMW clip file corresponds to superseded 51 76 7 162 587, now 51 76 5 A71 150; the custom glue-in double stud is not separately serviced and no moulding assembly number is assigned. Use heat- and UV-resistant material plus high-strength compatible adhesive, follow the creator's hook orientation, and verify full roof travel, strip retention, drainage and sealing before driving.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Clip-on key-fob holder designed and physically demonstrated in the cup-holder trim of a BMW F33 4 Series Convertible. The creator confirms the fit in his F33; no fitment to visually similar 1–4 Series interiors is inferred. Use cabin-heat-resistant material, dry-fit the clip, and verify that it cannot obstruct the controls, selector, handbrake or cup-holder use.

Fits 4 Series · F32 / F33 / F36 / F82 / F83

Left and right replacement brackets for retaining the metal badge inserts in BMW G20/G21-family all-weather floor mats. The creator reports iterative fit testing and explains that the metal tabs pass through the bracket openings before the bracket is press-slid into place. Use PETG or ABS, fit only to the mat badge area, and verify the mat remains fully anchored with no loose piece or raised edge near any pedal before driving.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

Console insert for BMW G20 and G21 3 Series cars without the factory wireless-charging trim, physically shown installed after removal of the original rubber mat. It accepts an Apple MagSafe puck, a 90-degree USB-C adapter and a slim 12 V USB-C adapter. Use cabin-heat-resistant material, secure and protect the cable, preserve access to controls and cup holders, and confirm the phone remains retained without obstructing driving controls.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

Two-piece fold-down bag hook designed and physically demonstrated in the trunk of a BMW G20 3 Series. Install with an M6 nut, a 25–40 mm M6 socket-head bolt and a temporary nut-retaining aid as described by the creator. Use cabin-heat-resistant material, confirm the mounting point is structurally suitable, keep the load light and verify the hook and cargo cannot interfere with the trunk lid, wiring or emergency equipment.

Fits 3 Series · G20 / G21 / G28 / G80 / G81

TPU clutch-stop set in 10, 12, 14 and 16 mm heights for manual BMW F3x models; the creator reports the 16 mm version installed with the factory clutch. Use the specified material, inspect layer adhesion and fit, and stop if the part interferes with safe service or pedal operation.

Fits 3 Series · F30 / F31 / F34 / F80

Scanned right-side F30/F31 headlight support bracket shown fitted in place by the creator. Use exterior-rated material and verify retention, weather sealing, lamp aim and washer operation before driving.

Fits 3 Series · F30 / F31 / F34 / F80

Clip-on shopping-bag hook demonstrated on the factory rear parcel-shelf cover of BMW F31 and G31 Touring models. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80 · 5 Series · G30 / G31 / G38 / F90

Parametric insert demonstrated in the sliding-cover cup holder used by BMW F30/F31 and F32/F36 LCI interiors. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80 · 4 Series · F32 / F33 / F36 / F82 / F83

4.5 mm depth adapter for installing a BLAM BM200W 200 mm subwoofer in the original HiFi enclosure of a BMW F34 3 Series Gran Turismo. Use cabin-rated material, isolate wiring and connectors, and verify secure fit and unobstructed speaker operation.

Fits 3 Series · F30 / F31 / F34 / F80

Two-piece open- or closed-loop umbrella mount demonstrated on the inside of an F31 Touring boot lid. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

Small storage bin fitted beside the handbrake lever in a BMW F30 328i. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80