Every printable part.

Replacement rotary air-conditioning control knob for the 2006 Wrangler TJ, including a small hole for a contrasting filament position marker.

Fits Wrangler · TJ

Tight-fitting flexible replacement end for a TJ sun visor pivot.

Fits Wrangler · TJ

Springless replacement for the failure-prone upper soft-door window latch, measured from the factory part and installed on the creator's Wrangler.

Fits Wrangler · TJ

OEM-shaped replacement heater-control knob for the 1997 Wrangler TJ, measured from an original control and physically installed by the creator.

Fits Wrangler · TJ

OEM-shaped replacement rotary heater and air-conditioning control knob for 1999–2001 Wrangler TJ dashboards, measured from original controls and physically installed by the creator.

Fits Wrangler · TJ

Replacement hood-mounted clip for the prop rod on a 1997 Wrangler TJ, with the round hood-hole mount verified by the creator.

Fits Wrangler · TJ

Full replacement interior release handle modeled after the TJ original. The creator installed the design and reported it still working after approximately nine months.

Fits Wrangler · TJ

Replacement mounting bracket and pivot pin for the factory Hella fog light used on 2004–2006 Wrangler TJ models, supplied as both a one-piece print and a reinforced multipart option.

Fits Wrangler · TJ

Quarter-turn threaded replacement floor plug tested in a 1998 TJ. The slot accepts a US quarter as an installation tool.

Fits Wrangler · TJ

Replacement geared and plain internal flaps for a TJ dashboard vent that can no longer close.

Fits Wrangler · TJ

Large-drink cupholder that bolts to the rear seat-mount area. The creator explicitly identifies and photographed TJ and JK fitment.

Fits Wrangler · TJ · Wrangler · JK

Snap-in replacement bracket that secures the manual-transmission shifter boot to the TJ center console, modeled from the broken original and test-fitted in PETG.

Fits Wrangler · TJ

Adapter ring that mounts a 6.5-inch speaker in the factory TJ speaker pod without modifying the pod, using the original vehicle hardware and four M3 speaker screws.

Fits Wrangler · TJ

Replacement nut clip for the screws that secure the TJ's chrome headlight trim ring when the original clips strip.

Fits Wrangler · TJ

Snap-in blanks for the 2001 TJ center-console switch opening, supplied as a plain filler and a version for a common round rocker switch.

Fits Wrangler · TJ

Flexible replacement sleeve for either end of the TJ soft-top tailgate bar. The creator modeled the combined rubber-and-plastic original as a single TPU part.

Fits Wrangler · TJ

Left and right faceplates and enclosures that replace the TJ's front dashboard speaker mounts with 5.25-inch pods. The creator printed, installed and evaluated the complete set.

Fits Wrangler · TJ

Protective clips that snap over the lower edges of removed TJ doors before they are set on concrete or sand.

Fits Wrangler · TJ

Hinged hook sized around the TJ's approximately three-inch padded roll bar. The revised left and right halves add a lower M3 closure to prevent spreading when unloaded.

Fits Wrangler · TJ

Adapter that fits a short, wide Toyota-pattern push switch into the factory Jeep switch panel. The creator specifies 1997–2004 Wrangler TJ and 1997–2001 Cherokee XJ applications.

Fits Cherokee / Liberty · XJ · Wrangler · TJ

Replacement bushing that removes play from the tilting passenger-seat slide mechanism on the 2002 Wrangler TJ.

Fits Wrangler · TJ

Three-piece wall-mount system that supports removed TJ doors from their factory hinge points instead of the window frame. The creator printed and load-tested the PETG design.

Fits Wrangler · TJ

Replacement end cap for the stock 1997–2006 Wrangler TJ front bumper. Two copies complete the bumper.

Fits Wrangler · TJ

Large hand knob for converting TJ hardtop fasteners to tool-free quick-release hardware. The model is sized for a captured bolt and broad hand grip.

Fits Wrangler · TJ