Every printable part.

Replacement end cap for the stock 1997–2006 Wrangler TJ rear bumper. The creator test-fitted the design on a European-market TJ.

Fits Wrangler · TJ

Two-piece replacement for the heat-damaged European-market license-plate light mounting and outer cover, designed around LED illumination on a 2004 Wrangler TJ.

Fits Wrangler · TJ

Exact-replica replacement foot for the removable rear bench seat, modeled from the part in a 2000 Wrangler Sport and designed to reuse the original embedded washer and screw.

Fits Wrangler · TJ

Small-diameter bow knuckle used by the creator to convert a factory TJ soft top to a flip-up configuration.

Fits Wrangler · TJ

Replacement lower bracket for the automatic-transmission shift-indicator assembly used across the 1997–2006 Wrangler TJ. The printed bracket accepts the original upper cover and hardware.

Fits Wrangler · TJ

Left- and right-hand replacements for the break-prone plastic soft-top rail pins or sliders used on 1991 vehicles. Both original downloadable meshes are included.

Fits Wrangler · YJ

Separate circular and rectangular flexible liners that replace the original rubber center-console insert without print supports. The physical photograph documents the original one-piece texture and layout.

Fits Wrangler · YJ

Slip-on clip that holds the door courtesy-light switch open so the interior lights remain off when the doors are removed. It was designed around the pictured replacement switch.

Fits Wrangler · YJ

Two printable plastic spacer components for repairing the horn-button assembly. The source only verifies the YJ application, so other same-era vehicles were not linked.

Fits Wrangler · YJ

Paired stops that fit around the mirror-arm mounting nuts to limit mirror movement. The creator installed ABS prints and provides fitting cautions for seating the nut without overloading the part.

Fits Wrangler · YJ

Four-piece left- and right-hand replacement set for the discontinued soft-top bow ends. Physical photographs compare the printed parts with the originals and show the assembly positioned on the body rail.

Fits Wrangler · YJ

Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1

Close replica of the factory dashboard switch plate with openings for three standard toggle switches. The creator printed and installed the panel in PETG.

Fits Wrangler · YJ

Two low-profile front turn-signal housings for LED conversions, with 12-by-12 and 20-by-20 heatsink openings. The creator installed the design to gain intercooler clearance while retaining the original lamp location.

Fits Wrangler · YJ

Hooks that slip under the soft-top rails and accept shock cord or resized paracord to keep the folded top from moving.

Fits Wrangler · YJ

Replacement retaining clip for the 2.5-litre airbox. The creator trial-fitted nylon prints on a 1990 vehicle, road-tested them and explicitly identifies the matching Comanche application.

Fits Comanche · MJ · Wrangler · YJ

Replacement slider knob for the defrost, heater and vent controls. It was measured from a broken original, physically compared with the original and test-fitted successfully.

Fits Wrangler · YJ

Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.

Fits CJ · CJ-7 · Wrangler · YJ · Wrangler · TJ

Twist-on replacement cap for the windshield-washer fluid reservoir. The source notes that reservoir use requiring a vent tube is a different configuration and was not claimed.

Fits Wrangler · YJ

Replacement door-hinge liners with separate early, later and driver-side printable variants. Source naming and year-marked files support late CJ, YJ and TJ applications.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +2

Rear-seat cupholder that slides into the factory soft-top track and is retained by an existing track screw. The creator recommends high infill around the mounting tabs and upright.

Fits Wrangler · YJ

License-plate bracket with a channel for an LED strip and a separate clear printable lens. The two-part design mounts in the stock late-CJ and YJ location.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1

Bracket for relocating a winch-controller jack into a grille slot. Exact grille spacing should be checked before drilling or wiring; speculative CJ and TJ fitment was not assigned.

Fits Wrangler · YJ

Printable rectangular taillight lens for the standard late-CJ and YJ rear lamp housing. The creator printed it in clear ABS for use with red and white LED bulbs.

Fits CJ · CJ-5 · CJ · CJ-7 · CJ · CJ-8 Scrambler +1