Find your next part.

The stock sliding cover was slipping and wouldn't catch the rear part anymore so I made this one to have it be functional.

Fits Forester · First generation (SF) · Impreza · First generation (GC/GF/GM)

Lost one of my screw head covers from the door release handle of my Subaru Forest (2004). Designed this to replace, fits well, if needed use a lighter etc to soften the prongs and gently tease outwards slightly to get a better fit (secure clip). Be careful as they are delicate. Print a few at a time to give yourself spares, and also keep the print head moving allowing the tiny clips to cool between layers. Print in ABS (might be ok in PLA, just be super careful with the prongs!)

Fits Forester · Second generation (SG)

Printed with 0.4 nozzle and 0.1 resolution. Infill 100% ofc. Layed on back with supports. Fits and works well.

Fits Forester · First generation (SF)

On my Subaru Forester SG 2005 install is plug and play. I print it in TPU end 2019 , after cleaning looks like new ABS hold only 3 month

Fits Forester · Second generation (SG)

I designed this speaker adapter to mount a pair of hertz speakers for a friend on his Subaru Forester (model year 1997). The speakers are 165mm wide and he bought them from amazon (Hertz dcx 165). The adapter can be mounted on the front doors panel using the original screws and to link the speaker to the adapter you have to use the original screws plus one because it has four holes. To prevent vibration on the panel, it's recommended to put a little layer of insulation material on the adapter's surface that is in contact with the door's panel (as the original speaker mount). The adapter has two grooves, to pass the wires; and the higher depth of the speaker isn't a problem for the door glass (when you pull it down), it doesn't touch it. Ho progettato questo adattatore per montare un paio di speaker Hertz sulla Subaru Forester di un amico (modello anno 1997). Gli speaker hanno diametro 165mm e sono stati comprati su amazon (Hertz dcx 165). L'adattatore può essere montato sul pannello porta (portiere anteriori) utilizzando le tre viti originali e per montare lo speaker all'adattatore si possono usare le viti originali, più una dato che la cassa ha un foro di fissaggio in più. Per evitare vibrazioni e rumori, si consiglia di mettere un leggero strato di materiale isolante sulla superficie dell'adattatore in contatto con il pannello porta (come nel porta-speaker originale). L'adattatore presenta due scanalature per far passare i cavi; e la profondità maggiore dello speaker non è

Fits Forester · First generation (SF)

Subaru Forester 1996-2002 CAP-WASHER TANK Original part #86615 I lost my own and print to replace it. There are latches on the inside of the washer cap. And I also made a loop where you can tie a rope so that you don’t lose it again! :) --- Subaru Forester 1996-2002 крышка бочка омывателя. Оригинальный номер #86615 Свою я успешно где-то потерял, придумал замоделить. Внутри крышки защёлки. А также сделал петлю куда можно привязать шнурок чтобы больше её не потерять! :)

Fits Forester · First generation (SF)

Coin holder for your Subaru Forester SH.

Fits Forester · Third generation (SH)

I was tired of there being a single large pocket in my center console. I will probably use this as a starting point for additional versions but the interfacing geometry that mates up with the existing console are all in the correct place. This should fit all SH series Subaru Foresters 2009 - 2012 Designed in Fusion 360

Fits Forester · Third generation (SH)

It never really felt right to put my round cup into the square cup holders in my Subaru so I decided to make an insert. I will probably tweak the round portion to work with different sized cups a little better but this version works great for my current coffee mug. The fit in the existing cup holder fits like a glove. Designed in Fusion 360.

Fits Forester · Third generation (SH)

It's a coinbox that fits in the middle console - the console with a hatch underneath the armrest.

Fits Forester · Second generation (SG)

Retention clip broke off form my fuse box door on my 2009 subaru forester. This is the one on the drivers side right near where your left knee would be. Printed on its side to give the bottom hinge clips some flex without breaking

Fits Forester · Third generation (SH)

The cover, plug or insert is for the transmission release whole that is usually in the upper left of the automatic shifter in the Subaru Forester. It is very similar to the Outback (Part No: 35181AG00A) however the Outback part is about half the height of the Forester Cover Release. The Cover Release is individual sold for the Outback but in order to get it for the Subaru Forester you have to buy the whole shift indicator plate (Part No: 35170FG080) for the console. It costs anywhere between $80-$125 dollars.

Fits Forester · Third generation (SH)

Subaru Forester SH 2009-12 To fit the large storage hole in the front centre dash area (below the heater controls)> I found I didn't like putting anything in there as it was always on "show" for potential thieves etc. So the idea was to have a small cubby hole with door, and then a small tray above (tray fits next to the 12v socket above the door/frame.) Works ok, is reasonable "neat" - fix in place using (a large amount of) double sided foam trim tape. PETG or ABS preferred due to heat in cars may warp PLA, but I have had success with PLA in cars, as long as not in direct light etc (which this is not). First attempt so could be improved. Dry fit and measure the position first, the frame needs to be in place first so measure vs the tray. 1mm x 6mm magnets in the lid/frame. 2mm (M2) bolts in the hinges of the lid. Feel free to modify or improve.

Fits Forester · Third generation (SH)

Pull Handle OPENNER for Subaru Forester SF LH can b mirr to RH? dntknw

Fits Forester · First generation (SF)

a shortram like K&N 69 Typhoon sportairfiltersystem for SUBARU FORESTER (SG) 2.5 XT / 69-8002TS ( https://www.knluftfilter.com/69-8002ts-performance-air-intake-system ) its fittet for 100mm K&N airfilter original MAF sensor

Fits Forester · Second generation (SG)

Modified to fit a Pocophone F1 with case horizontally, other phones may required longer or shorter arms.

Fits Forester · Second generation (SG)

Centre divider for the console next to handbrake area. I lost the removable "wall" so quickly knocked this up.. Fits fine, but doesnt stack on the other divider unfortunately.

Fits Forester · Third generation (SH)

Trying to find a phone mount that would work on my 2020 forester sk. I didn't want something that will block an air vent or go into my cd player or occlude my view to any displays or windows. I wanted it to work with my magsafe car adapter that I bought on amazon to work with my iphone. This mount will attach to the right side console right below the color trim. It utilizes a standard 17mm ball mount so it can work with any accessory that attaches with a 17 mm ball mount. I am using this magsafe car mount https://www.amazon.com/gp/product/B08CZPVLNL/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1 The look is very clean and sturdy. I used 3M outdoor strength double sided stick pads to stick to the console.

Fits Forester · Fifth generation (SK)

If you like the design and wouldn't mind, please give me a watch and subscribe on youtube...I have videos designing these types of things from time to time and could use the support! My Youtube > https://bit.ly/35j5BL1 IG - @Myowncasualty IG - @EndMotive I printed this on an Elegoo Mars....supports will be hard to remove on an FDM printer without dissolvable support material. Fits LHD Subaru Forester SF/SG ....make sure your dash matches the one pictured. Includes 52mm and 60mm variant. No hardware or anything required. Just remove the factory dash vent carefully and this will clip in place just like the factory part. Also has a small routing hole to run wires. The vent still functions....just not as good lol.

Fits Forester · First generation (SF) · Forester · Second generation (SG)

This is a simple tool for installing your Cam Oil seals flush (I got frustrated with useless install kits that pushed it in too far or not straight) This was for my Subaru Forester 2010 SOHC, it has 45 x 32 x 8.0mm cam oil seals Just tap in with a light rubber mallet, worked great Designed in Tinker CAD, which I am getting the hang of, bit by bit I used random z seam &10% support , comes out easy on PLA+

Fits Forester · Third generation (SH)

To get stability in the middle bottom area, you should bend a sheet metal strip by 90° and fix it in the direction of the rear bumper. take TPU, ABS are not durability

Fits Forester · Second generation (SG)

forester_sf_5_radiator_grill_mount

Fits Forester · First generation (SF)

A printer friendly version of pimaster's [2004 Subaru Forester Bonnet Stay Clip](https://www.thingiverse.com/thing:213626)

Fits Forester · Second generation (SG)

Clip-under cover, front, 56411FA000 Part 4 on this page: http://opposedforces.com/parts/forester/en_s11/type_9/body_equipment_exterior/under_cover_and_exhaust_cover/illustration_1/ Subaru Forester SG '04, April — '05, May '05, March — '06, May '06, April — '07, May '07, March — '07, November Part usage information Europe FORESTER S11 FORESTER S10 IMPREZA G11 IMPREZA G10

Fits Forester · Second generation (SG) · Impreza · First generation (GC/GF/GM) · Impreza · Second generation (GD/GG)