Find your next part.

3D-printable holder for a Samsung Galaxy Note 9. The printed rail mounts between the radio and dashboard/vent area and supports the phone in front of the center vents. Verified fitment covers 2012-2016 Impreza and 2013-2017 Crosstrek vehicles. The printed holder is the modeled component; the phone and any non-printed mounting hardware are not included.

Fits Impreza · Fourth generation (GJ/GP) · XV / Crosstrek · First generation (GP)

Replacement lower instrument-panel cover that fills the factory switch/blanking-panel opening and restores the retaining features of the original cover. Verified fitment is the first-generation Subaru Impreza GC/GF/GM and first-generation Forester SF, corresponding to OEM 66813FA000; verify the dashboard variant and retention before installation.

Fits Forester · First generation (SF) · Impreza · First generation (GC/GF/GM)

Full-size storage bin that clips around the retaining features of a driver-side fuse-panel lid and provides a compartment for keys, spare fuses, cash, or other small items. Designed for fuse-lid part number 66135AJ020 and verified for the accepted Subaru generation IDs. Print the selected geometry in PETG for improved resistance to heat inside a vehicle; reorient the model flat on its base and verify clip engagement, clearance, and retention before use.

Fits Ascent · First generation (WM) · Forester · Fourth generation (SJ) · Forester · Fifth generation (SK) +8

Two-piece overhead map-light accessory switch mount for the 2008-2011 Impreza and 2008-2014 WRX/STI. It mounts four generic 22 x 38 mm rocker switches ahead of the map light, uses the factory map-light bezel screws, and supports optional fastening to the upper windshield frame. The selected set includes the upper bracket, a holey bucket with access holes for hard-mounting, and an editable STEP version. Supports and minor filing or redrilling may be needed; PETG or another heat- and UV-resistant material is recommended for in-vehicle use.

Fits Impreza · Third generation (GE/GH/GR/GV) · WRX · First generation (VA)

Single-piece center-console cup-holder insert for the 2001 Subaru Impreza. It drops into the center-console opening, adds a round recess for larger drink vessels, and retains a small adjacent storage pocket. Verify console variant, final scale, clearance, retention, and heat suitability before driving.

Fits Impreza · Second generation (GD/GG)

Cap-style oil-filter removal wrench for vehicles using Subaru filter 15208AA15A. It seats around the filter canister to aid hand removal during oil changes; verify the filter number and fit before applying torque. The packet contains one wrench geometry.

Fits Ascent · First generation (WM) · Forester · Third generation (SH) · Forester · Fourth generation (SJ) +12

Full-size functional adapter that clips into the bottom of a Momo Race Air gear knob and retains the leather shift boot/gaiter beneath the knob. Fitment is source-backed for a 2002 Subaru WRX within the second-generation Impreza GD/GG application represented by generation 1197. Print in PETG for cabin heat resistance, verify the knob and shifter interfaces before installation, and confirm secure retention before driving.

Fits Impreza · Second generation (GD/GG)

Full-size two-section adapter for a factory front center-console cup-holder opening. It enlarges the opening to retain a 40 oz water bottle; the printed geometry has approximately 95 mm upper inner diameter, 70 mm lower inner diameter, and a 100 × 145 mm overall envelope. Use a heat-resistant filament such as PETG or ASA; the source print guidance specifies no supports.

Fits Impreza · Third generation (GE/GH/GR/GV) · Impreza · Fourth generation (GJ/GP) · WRX · First generation (VA) +2

Replacement latch for the lower center-console storage box on the second-generation Subaru Impreza (GD/GG), source-verified for the 2002 application. It restores the lid retention function using the existing console interfaces. The single included STL is intended for PETG or ASA for cabin heat resistance; verify console variant, latch engagement, clearances, and secure retention before installation.

Fits Impreza · Second generation (GD/GG)

Full-size replacement hood support-rod retaining clip for the 2011-2016 Subaru Impreza (GJ/GP) represented by generation 1199. It secures the hood prop rod in its retaining position. Print in PETG at 100% infill as specified for the model, and verify rod diameter, clip engagement, hood clearances, and secure retention before road use.

Fits Impreza · Fourth generation (GJ/GP)

Console organizer tray with a cord pass-through opening and integrated coin compartments for the upper center-console storage area. Verified fitment: 2012-2017 Subaru XV/Crosstrek first-generation GP and 2012-2016 Subaru Impreza fourth-generation GJ/GP.

Fits Impreza · Fourth generation (GJ/GP) · XV / Crosstrek · First generation (GP)

Larger headlight cover for 2003-2005 Subaru Impreza GD/GG Blobeye headlight assemblies when LED lights are installed. Reuse the original seal rings. The model provides one cover; use an automotive-temperature filament appropriate for the installation environment.

Fits Impreza · Second generation (GD/GG)

Two-cup holder with cylindrical drink recesses and a rear mounting plate for the specified first-generation Subaru Impreza cup-holder area. It is intended to hold beverages during vehicle use. Verify the specific interior/console variant, retention, clearances, and heat-resistant print material before installation.

Fits Impreza · First generation (GC/GF/GM)

Flexible replacement grommet that retains the hood support rod at the front hood mounting point. Verified applications include the listed Impreza, Legacy, Outback, Forester, and Baja generation IDs; compare the original opening and rod diameter before installation. TPU is the intended material, and this work-in-progress design should be inspected for secure retention before vehicle use.

Fits Baja · First and only generation (BT) · Forester · First generation (SF) · Forester · Second generation (SG) +11

The stock sliding cover was slipping and wouldn't catch the rear part anymore so I made this one to have it be functional.

Fits Forester · First generation (SF) · Impreza · First generation (GC/GF/GM)

2024/01/12 - Update. The resin printed part became brittle and unfortunately broke after almost a year of use. Perhaps a ‘thicker’ version or different resin would hold up longer. 2023/01/28 Replacement brackets to hold heater instrument control in place. Contains direct replacement for out-of-production parts 66201FC020 and 66201FC020. I needed this part to convert to double-din console, European Subaru dealer couldn't order this part anymore. Original part is 1mm thick, recreated part is 2mm thick due to needed sturdiness and fits fine, without spacing. Print in resin or be wary of print direction and warping temperatures for inside of car. Double holes should be on top: 66201FC020 is left hand side (LH) 66201FC030 is right hand side (RH) Installation Advice: Insert into center sidewall first, since these are blind screws otherwise. Screw and bracket need to be fit tightly, otherwise heater control panel will move forward slightly creating a gap with the panel. Insert center console back into dash. Move heater instrument in place and screw in place Place dash front panel and click in place Put gear shift panel in back place Put handbrake panel back in place

Fits Impreza · First generation (GC/GF/GM)

This is a printable replacement for a Subaru Impreza hood support rod end cap - or whatever you want to call the plastic part that fits into the hood slot when the rod is raised. This piece (white piece in picture) broke on our 2016 Impreza and Subaru seems to only sell the entire rod, not just the cap piece, so I decided to take a whack at modeling and printing a new one. I'm new to Fusion 360, so it took a few tries, but this one is working nicely for me. I'm not sure which other Subaru models/years this would work for, but there's not really much to it, so if it looks like the part in the picture, you can give it a shot! The part is pretty close to the original, though I did beef it up a bit in the area where the original one broke. I also set infill at 50% which might be overkill, but it seemed better to overbuild. You'll need to print with supports, and be sure to have your xacto handy to do some somewhat fiddly cleanup. I printed this using Prusament Galaxy Black PLA, mainly because it's all I have on hand, but let's face it, the engine compartment of a Subaru Impreza could use a little glittery bling, right?

Fits Impreza · Fourth generation (GJ/GP)

I had a first world problem: My oversized water bottle wouldn't fit in my new car cup holder. This is my solution. Print this in PETG, ABS or something with a high glass transition temperature or it WILL melt. Hope this is useful to somebody.

Fits Impreza · Fifth generation (GK/GT) · XV / Crosstrek · Second generation (GT)

My wife drives a Subaru Impreza and her passenger sun visor broke one day. Turns out a plastic connector piece broke roughly in half. Unfortunately you can't buy just the one piece that broke, you have to spend $90 to buy a whole new visor! So to save a little money I figured I'd design a replacement part. This is specifically for a 2017 Subaru Impreza Premium Sport Hatchback. It is only for the passenger side visor, but I imagine that a mirrored version would work on the driver side visor. I have included both the Fusion360 archive and a generated STEP file so that this can easily be remixed. Apologies in advance if remixing my design is a pain, I'm still relatively new to 3D CAD and this is the most complex thing I've designed so far.

Fits Impreza · Fifth generation (GK/GT)

This is a an adapter to mount a Yakima Ski Rack to my 2018 Subaru Impreza Stock Crossbars. Did not like the expensive adapters Yakima sells, they didn't seem as secure nor as stable. Print four of these in total, two for each rack. These adapters can snap over the crossbars and be slid into place. When the ski rack is tightened, the mounts grip and do not slide. I printed these in PETG. I did not strength test these, but have not had any problems driving at highway and interstate speeds. Will update with any problems. Might work with Subaru Crosstrek as well, since a lot of parts are interchangeable.

Fits Impreza · Fifth generation (GK/GT)

This thing is a replacement part for 3rd gen Subaru Impreza cup holders. It may fit other Subaru models from that same period. It helps center a standard diameter beverage can in the cup holder so it doesn't slide around. It also collects condensation and leaked drink. It probably could use an extruded honeycomb pattern to give liquid a place to run off to...

Fits Impreza · Third generation (GE/GH/GR/GV)

Clip-under cover, front, 56411FA000 Part 4 on this page: http://opposedforces.com/parts/forester/en_s11/type_9/body_equipment_exterior/under_cover_and_exhaust_cover/illustration_1/ Subaru Forester SG '04, April — '05, May '05, March — '06, May '06, April — '07, May '07, March — '07, November Part usage information Europe FORESTER S11 FORESTER S10 IMPREZA G11 IMPREZA G10

Fits Forester · Second generation (SG) · Impreza · First generation (GC/GF/GM) · Impreza · Second generation (GD/GG)

Horncover for Subaru Impreza G3 (2.0D) (60mm Horn)

Fits Impreza · Third generation (GE/GH/GR/GV)

I made this visor clip for as a replacement for a broken one. It fits a 1993 subaru impreza so it should work on a 93-99 impreza. Works great but the shape is slightly different from the oem part as mine was broken.

Fits Impreza · First generation (GC/GF/GM)