Find your next part.

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +8

Simplified, smaller front bumper corner for the full-size Range Rover Classic 200Tdi. Attaches using the original screw. Confirm side and dimensions against the vehicle before printing.

Fits Range Rover · Classic

Height-setting blocks for calibrating Range Rover P38 electronic air suspension level sensors. Includes front and rear blocks for Access, Low, Standard, and High settings

Fits Range Rover · P38

Simplified 78 mm centre hub cap for Range Rover Classic alloy wheels. Prints without supports.

Fits Range Rover · Classic

Replacement sunroof rail and locking bracket for the P38 electric sliding roof. Related genuine guide assemblies are EXM100360 (RH) and EXM100370 (LH)

Fits Range Rover · P38

Custom replacement for the front ashtray section of a 1999 Range Rover P38 4.0 automatic. Includes a standard cigarette-lighter socket opening, space for additional switches, a 2 mm smaller version for vinyl covering, and separate mounting brackets for printers with smaller beds. The related 1999 front centre-console ashtray assembly is Land Rover FKH100350

Fits Range Rover · P38

Simplified fixed replica of the original Range Rover Classic dashboard vent grille. The source model is based on a full-size Classic and is intended to be glued in place.

Fits Range Rover · Classic

Dashboard blanking plate for a full-size Range Rover Classic when no car radio is installed.

Fits Range Rover · Classic

52mm hub nut socket for a wide range of Land Rover models. Most wheel bearings only need gentle torque - a few later models use the same nut but with huge torque and this likely won't work for those. 1/2" socket plus a 27mm (wheel nut) sized hex on the back. Designed to be printed without supports. Print in something robust.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Discovery · 1 +5

Workshop fitting tool for seating the rear hub seal squarely.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +3

Custom panel for a Range Rover P38 stock radio slot, holding auxiliary switches, the ride-height switch, and the interior-air-temperature sensor after relocating the original radio. This is a community accessory with no Land Rover Genuine part number. The source recommends printing the front panel flat on the bed at about 20% infill without supports.

Fits Range Rover · P38

Dashboard drinks holder for the Range Rover P38, based on genuine Land Rover accessory LRN32685 with printability changes and an added tray for pens and coins.

Fits Range Rover · P38

Replacement protective sleeve for the Range Rover Classic heated rear-window cables, Land Rover part 589818. The source author changed the original round section to a square section and tuned the curvature for fit. PETG or nylon is preferable to brittle PLA. LR3DParts converted the original ASCII STL to binary STL without changing its geometry for upload compatibility.

Fits Range Rover · Classic

Replacement fuse-box cover for the full-size Range Rover Classic.

Fits Range Rover · Classic

Phone holder designed to sit in the front coin tray, sized around an iPhone 11 in an Apple case. Confirm phone and tray dimensions before printing and use a heat-resistant cabin material.

Fits Range Rover · L322

Replacement push clip for the front cowl and wiper-panel cover on 2002–2009 vehicles. Use a flexible, weather-resistant material and compare dimensions with an original clip before fitting.

Fits Range Rover · L322

Fuse cover designed for an approximately 1993 Range Rover Classic 200Tdi. Uses one M3 x 25 screw. This is the screw-retained alternative to the standard fuse-box cover.

Fits Range Rover · Classic

It fits in front of the ignition-switch, designed for the eezee power switch panel so it has a mounting surface of 68x115 mm and mirrored version for RHD vehicles

Fits Range Rover · L322

Stable funnel that sleeves over the 18 mm AdBlue filler tube and rests on the adjacent air intake. It has approximately half-litre capacity, 3 mm debris-filter holes, an air-escape tube to prevent glugging, and a measured gravity-flow rate of about two litres per minute. A separate 1.7-litre pouring jug is included.

Fits Range Rover · L405

Two replacement locating-pin variants for the loadspace cover: one for an M8 opening and one for the original 11 × 11 mm square opening. Print horizontally to reduce delamination risk.

Fits Range Rover · L322

Replacement end piece for a longitudinal roof rail.

Fits Range Rover · L322

Protective bung for a factory Westfalia detachable-towbar receiver, intended to keep dirt and moisture out when the hitch is removed. Check receiver dimensions before printing.

Fits Range Rover · L322

Replacement internal bar for a broken cabin heater and air-conditioning vent grille. Confirm vent position and dimensions against the original before printing.

Fits Range Rover · L322

Two-part holder and lid for mounting a Nexus 9 tablet in a 2002–2012 dashboard installation, suitable for an Android Auto client or other tablet-based interface. Editable OpenSCAD sources are included.

Fits Range Rover · L322