Find your next part.

A cup holder that clips to the metal dash of a Series 1-2a.

Fits Series · 1 · Series · 2 · Series · 2A

Holds the seatbelt latch so it does not slide down past the shoulder. Universal to any seatbelt of standard width. (3MF file)

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +8

Its an alternative to the front grille screw plastic mounts.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +3

Three-part replacement socket assembly for an indicator or position lamp using a separate single-contact bulb holder. Verify the 33 mm housing fit, wiring, insulation, and weather sealing.

Fits Series · 1 · Series · 2 · Series · 2A +1

Six-piece replacement kit redrawn from surviving original plastic and bakelite wiper-motor components. The positive-terminal insulator uses a simplified M3 through-bolt connection.

Fits Series · 1 · Series · 2 · Series · 2A

Replacement ventilator control knob modelled from the original component.

Fits Series · 2

Originally built to mount a Bolt&Trim Leather speaker holder for the Marshall speaker. This allows for a temporary/movable mount based originally on a cup holder. Could be easily modified for other speaker styles.

Fits Series · 1 · Series · 2 · Series · 2A

Replacement lettered knob for a missing bulkhead-vent control. It is designed to be heat-pressed onto the original mechanism

Fits Series · 3

If you mount the MRC7354 "Soft Top Front Seat Belt Bar For Land Rover Defender / Series" the tube do not fit very well the the capping. This part gives it a nice an stable connection. Needs tu be drilled trough after mounting fpr a tight fit. Drill 8 mm oder 5/16 "

Fits Defender · 200 Tdi · Defender · 300 Tdi · Series · 2 +2

Loose- and tight-fit holders for fitting a 5 mm 12-volt LED and panel-mount bezel into a 16 mm Jaeger or Smiths gauge opening. The creator notes that the tight version may break during removal and suggests optional hot glue after installing the LED.

Fits Series · 2A · Series · 3

Door-hinge packing shims in three thicknesses. They also separate dissimilar metals to help reduce electrolytic corrosion

Fits Series · 2 · Series · 2A

Eleven thickness variants of the isolating shim fitted between the chassis brackets and rear tub to separate dissimilar metals.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +5

Replacement UP–DOWN heater airflow control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Fits Series · 2 · Series · 2A · Series · 3

52mm hub nut socket for a wide range of Land Rover models. Most wheel bearings only need gentle torque - a few later models use the same nut but with huge torque and this likely won't work for those. 1/2" socket plus a 27mm (wheel nut) sized hex on the back. Designed to be printed without supports. Print in something robust.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Discovery · 1 +5

Three-piece 12-volt inspection-lamp socket adaptation using standard 4 mm RC bullet connectors, 14 AWG silicone wire, and an M3 x 12 mm fastener.

Fits Series · 1 · Series · 2

Simple cab hook for retaining a loose seat belt when it is not in use. Confirm the mounting position and belt clearance before drilling or attaching it.

Fits Series · 3

Replacement plastic control for the Lucas wash/wipe switch. The sacrificial lower support can be removed after printing

Fits Series · 3

Tool for the slotted switch nuts

Fits Series · 3

Replacement lower-dashboard air vent in the later flat style.

Fits Series · 3

Workshop mandrel for centring the clutch plate during assembly. Confirm the spigot and spline diameters against the gearbox input shaft and clutch before use.

Fits Series · 2 · Series · 2A · Series · 3

Replacement support bracket for the instrument cluster where the original is missing or damaged. Compare handedness, hole spacing, and dashboard structure before printing.

Fits Series · 3

Replacement threaded button for the handbrake lever. The source recommends finishing the undersized bore with an M5 tap for a secure fit.

Fits Series · 2A · Series · 3

Replacement COLD–WARM heater control button. Compare the lever slot and lettering orientation with the original before printing and fitting.

Fits Series · 2 · Series · 2A · Series · 3

Bulkhead-mounted holder for a standard 33 cl can, with a recess for an optional 6 mm retaining magnet.

Fits Series · 1 · Series · 2