Find your next part.

Full-size printed phone holder designed for 2015–2021 WRX/STI interiors and sized by the creator for a large phone in a heavy case. The single-piece design provides the phone-supporting geometry; PETG or ABS is specified for in-car heat and supports are required for printing.

Fits WRX · First generation (VA)

A printed base that holds an Apple MagSafe charging puck in the storage cubby behind the shifter of the 2022+ VB WRX. The puck sits slightly proud of the base to clear phone-camera bumps. Attach the puck to the base and the base to the rubber tray with VHB tape, route cable slack beneath the base, and leave clearance at the left side for the phone and USB-C plug.

Fits WRX · Second generation (VB)

Full-size storage bin that clips around the retaining features of a driver-side fuse-panel lid and provides a compartment for keys, spare fuses, cash, or other small items. Designed for fuse-lid part number 66135AJ020 and verified for the accepted Subaru generation IDs. Print the selected geometry in PETG for improved resistance to heat inside a vehicle; reorient the model flat on its base and verify clip engagement, clearance, and retention before use.

Fits Ascent · First generation (WM) · Forester · Fourth generation (SJ) · Forester · Fifth generation (SK) +8

Two-piece overhead map-light accessory switch mount for the 2008-2011 Impreza and 2008-2014 WRX/STI. It mounts four generic 22 x 38 mm rocker switches ahead of the map light, uses the factory map-light bezel screws, and supports optional fastening to the upper windshield frame. The selected set includes the upper bracket, a holey bucket with access holes for hard-mounting, and an editable STEP version. Supports and minor filing or redrilling may be needed; PETG or another heat- and UV-resistant material is recommended for in-vehicle use.

Fits Impreza · Third generation (GE/GH/GR/GV) · WRX · First generation (VA)

Friction-fit inserts for the front and rear center-console cup-holder positions of the second-generation WRX. They reduce movement for slim 12 oz cans such as standard energy-drink cans. The V2 variant is intended for the front position and the V3 variant for the rear; print the required variant for the position being used. PETG or ABS is recommended for better heat resistance in a vehicle interior.

Fits WRX · Second generation (VB)

Two-piece center-tray wireless-charger enclosure consisting of a base and top cover. It fits the center tray of the 2022-2025 Subaru WRX VB, holds a separate wireless charging puck, retains a phone, and conceals the power cable. The top relief accommodates a Google Pixel 8 Pro in an OtterBox Symmetry case. Includes the base and top cover STL files; charging electronics and installation hardware are not included. Verify phone, charger, cable, console clearances, and cabin-temperature material suitability before installation.

Fits WRX · Second generation (VB)

Full-size two-section adapter for a factory front center-console cup-holder opening. It enlarges the opening to retain a 40 oz water bottle; the printed geometry has approximately 95 mm upper inner diameter, 70 mm lower inner diameter, and a 100 × 145 mm overall envelope. Use a heat-resistant filament such as PETG or ASA; the source print guidance specifies no supports.

Fits Impreza · Third generation (GE/GH/GR/GV) · Impreza · Fourth generation (GJ/GP) · WRX · First generation (VA) +2

Replacement latch for the center-console armrest lid. Restores the latch retaining and closing function for the 2015-2018 Subaru WRX STI center console; verify the latch geometry and engagement against the original part before installation. The source set contains one latch component.

Fits WRX · First generation (VA)

Subaru WRX side defroster vent mount for the Cobb Accessport. Did not need any additional hardware. Just pops right in and holds the accessport snugly. Tested on 2018 WRX model. This is an ongoing project. Check back for updates soon! ### Changelog #### Body3-angled.stl 2020-02-18 - Moved accessport body to the right of the vent. - Angled accessport body to face the driver.

Fits WRX · First generation (VA)