car3dparts.

1990–2000

3 Series E36

Verified catalog fitment for this exact BMW generation. 46 printable parts currently match.

318ti Rear 5.25-Inch Speaker Adapter PairC3D–01145
BMWCabin trim, cargo & roof

318ti Rear 5.25-Inch Speaker Adapter Pair

Left and right adapters for installing standard 5.25-inch rear speakers in the BMW E36 318ti Compact without cutting the original housings. The source shows the printed adapters, speaker assembly and installed housings. Verify speaker depth, wiring clearance and screw retention.

Fits 3 Series · E36

BMW Reverse Radio Side-Cover PairC3D–01111
BMWDashboard & controls

BMW Reverse Radio Side-Cover Pair

Replacement side covers for BMW Reverse RDS, non-RDS, Bavaria and Business radios used in E30, E32, E34 and E36. The source shows physical fit and finish; BMWFans confirms covering cap 65126907823.

Fits 3 Series · E30 · 3 Series · E36 · 5 Series · E34 +1

Trunk-Floor Twist LockC3D–01393
BMWCabin trim, cargo & roof

Trunk-Floor Twist Lock

Replacement for BMW OEM part 51478230749 (Support for Tension Strap). Used to secure the trunk floor panel in BMW E39 E36 models. Printing recommendation: For maximum strength, print the part at a 45° angle using supports. This print orientation improves layer adhesion in the areas subjected to the highest load, resulting in a stronger and more durable part. BMW catalog lists support 51478230749 from 1996-09 and records bilateral interchangeability with superseded 51478197822; retain the creator-listed E36/E39 fitment. Verify dimensions against the original part and confirm full operation before regular use.

Fits 3 Series · E36 · 5 Series · E39

Adjustable Clutch StopC3D–01322
BMWTransmission & drivetrain

Adjustable Clutch Stop

Adjustable clutch-pedal stop body for manual-transmission BMW E28 and other listed classic BMW chassis. Assembly requires an M10 screw, two M10 nuts, a 40 mm washer and a genuine-style rubber cap. Adjust only far enough to remove excess pedal travel while preserving complete clutch disengagement, then lock the nuts securely and re-check operation before driving.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +4

Oil Filter removal toolC3D–01179
BMWRemoval tools

Oil Filter removal tool

I used it for my BMW E46 and it is very sturdy. You can use a 32mm Hex Nut or a 1/2" square wrench to open the oil filter cap. The Tool on the picture was an earlier smaller version but it broke. Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E36 · 3 Series · E46

Bumper-Inlet Airbox DuctC3D–01176
BMWBumpers, grilles & guards

Bumper-Inlet Airbox Duct

Four-piece E36 bumper-inlet duct inspired by the Dinan layout and physically shown installed between the bumper opening and air filter. Print in heat- and impact-resistant material, bond the sections securely, and verify filter, fan, belt, water-ingress and road-clearance conditions on the exact car.

Fits 3 Series · E36

Factory Front Cupholder SpacerC3D–01170
BMWConsole & storage

Factory Front Cupholder Spacer

Replacement spacer for the front drink recess in the BMW E36 factory centre-console cupholder, physically shown installed. The creator lists accessory number 82111469119, but it was not independently resolved to this printed subcomponent and is intentionally omitted.

Fits 3 Series · E36

Touring Tailgate-Trim RetainerC3D–01169
BMWCabin trim, cargo & roof

Touring Tailgate-Trim Retainer

Direct replacement retainer for the BMW E36 Touring tailgate trim, physically shown installed at the lower edge of the open tailgate. Print in a tough material and confirm every stud and clip seats without distorting the trim.

Fits 3 Series · E36

Fog-Lamp LED Rear-Cap ExtensionC3D–01168
BMWExterior lighting, cameras & sensors

Fog-Lamp LED Rear-Cap Extension

Rear-cap extension physically fitted to an original BMW E36 fog lamp to clear the cooling fan on an LED replacement bulb while retaining the stock cap. Check bulb legality, connector strain, weather sealing, lamp clearance and heat before road use.

Fits 3 Series · E36

Engine-Bay Inspection-Lamp HolderC3D–01163
BMWEngine-bay electrical & sensors

Engine-Bay Inspection-Lamp Holder

Replacement holder for the BMW E36 engine-bay inspection lamp, physically printed by the creator. Use ABS, nylon or another engine-bay-rated material, secure the lamp wiring away from heat and moving components, and verify the lamp cannot detach.

Fits 3 Series · E36

318ti 168 mm Differential Output-Seal DriverC3D–01162
BMWInstallation & alignment jigs

318ti 168 mm Differential Output-Seal Driver

Service driver sized to install 168 mm differential output seals to the original depth on four-cylinder E36 and creator-listed Z3 applications. The source shows the physical tool on the differential. Use with a flat striking plate, measure seal depth, and inspect the seal lip before assembly.

Fits 3 Series · E36 · Z3 · E36/7 / E36/8

Passenger Air-Vent Knob and Linkage SetC3D–01160
BMWDashboard & controls

Passenger Air-Vent Knob and Linkage Set

Multi-part repair set for BMW E36 passenger air-vent knobs, arms, plugs, lever, washer and connectors. The creator physically assembled and installed the revised parts. Select the matching left/right pieces and verify every louvre moves freely without binding.

Fits 3 Series · E36

Compact Parcel-Shelf HookC3D–01157
BMWCabin trim, cargo & roof

Compact Parcel-Shelf Hook

Grooved replacement hook for the E36 Compact parcel-shelf cord, refined from the original model and physically compared with the stock hook. Print in a tough material and verify the cord releases without cracking the shelf.

Fits 3 Series · E36

16 mm Rear-Carpet Retaining RivetC3D–01151
BMWCabin trim, cargo & roof

16 mm Rear-Carpet Retaining Rivet

Replacement push rivet for the 16 mm rear carpet holes in BMW E36 luggage compartments. The creator shows the finished print installed in carpet. Print in a tough material, test removal on one location, and do not force it into a smaller opening.

Fits 3 Series · E36

Star Battery-Cell Cap WrenchC3D–01149
BMWService tools

Star Battery-Cell Cap Wrench

14 mm hex-drive hand tool for the star-shaped cell caps on the original battery in a 1999 E36. The source shows both the printed wrench and matching battery caps. Use only with the battery isolated, wear eye protection, and do not short the terminals.

Fits 3 Series · E36

Sunglasses-Cubby Triple 52 mm Gauge PanelC3D–01146
BMWDashboard & controls

Sunglasses-Cubby Triple 52 mm Gauge Panel

Three-gauge panel for the E36 sunglasses cubby, physically installed after widening the side clips by 2 mm. The uploaded orientation is for RHD; the creator directs LHD cars to mirror the model. Cutting the original cubby is required, so dry-fit the panel and preserve OBC and switch clearance.

Fits 3 Series · E36

Factory Cupholder Conversion Insert and RingC3D–01144
BMWConsole & storage

Factory Cupholder Conversion Insert and Ring

Two-piece conversion for the factory 1992–1999 E36 cupholder module, flattening and widening the support for modern cans and cups. The creator used the installed insert and documents 318i, 325i, 328i and M3 fitment. Use cabin-heat-resistant material and confirm the module still clips securely.

Fits 3 Series · E36