car3dparts.

1997–2006

3 Series E46

Verified catalog fitment for this exact BMW generation. 87 printable parts currently match.

Rear Armrest CupholderC3D–01200
BMWConsole & storage

Rear Armrest Cupholder

Cupholder insert for the rear armrest of BMW E46. The backing is inserted under the leather. Use the backing to mark the location for your cuts. A single slit in the center "web" is also needed to get the backing into the armrest. Carve out the foam as needed to clear the cupholder. Insert the backing, insert the cupholder and use 6 wood screws to hold them together. The screws I used have 4mm outer thread. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Windshield-Washer Filter / Strainer HolderC3D–01199
BMWWipers & washers

Windshield-Washer Filter / Strainer Holder

Many of these filters for the windshield washer reservoir get's broken and fall down into the water. The design is using the filter of the old holder and fits nice into your windshield water reservoir. Cut of the filter from the old holder. Glue it on the bottom. Cut off everything protruding. Done! The bar helps you to get the filter out for cleaning. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Rear Seat-Back Panel Repair ClipC3D–01198
BMWSeats & restraints

Rear Seat-Back Panel Repair Clip

Replacement upper retaining clip for the rear front-seat back panel, modeled from the surviving seat-panel clip profile and physically compared with the panel. The nearby V5BB Brombeer catalog number identifies the complete parent panel and is intentionally omitted. Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

Touring Hatch Carpet-Panel Repair ClipsC3D–01197
BMWCabin trim, cargo & roof

Touring Hatch Carpet-Panel Repair Clips

The carpeted panel on the interior of the E46 touring hatch is tricky to remove, and often the retaining clips are broken. I have created these two clips which can be epoxied in place to return normal function. In order to use them, completely cut the broken part of the clips out as shown in the photo then, use an epoxy like JB Weld liberally - the holes provide a mechanical bond for the epoxy. Note there are a right and a left. I did not create the center clip. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Convertible Hardtop CoversC3D–01196
BMWCabin trim, cargo & roof

Convertible Hardtop Covers

My wifes car was equiped with a Hard top, but during summertime the hardtop is removed and there were these big gaping holes in the plastic trim. Apparantly there is a cover that fits there, but they cost aroun €60-80, each.. Can't have it that way and i wont pay that crazy amount for some plastic. Designed my own and sanded and plastidipped in black.. Looks good enough for me.. If you don't want to make one self, search for these part numbers on ebay or your local bmw dealer. 51717022385 51717022386 PS: The bunny ears will break, so just break them of before mounting.. They never aligned up but the part will not fall away.. it is snugg fittment. :) Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Cupholder ExpanderC3D–01195
BMWConsole & storage

Cupholder Expander

[*TIRES SQUEAL AROUND TIGHT BEND* "Ugh, there goes my polar pop!"] Don't let this be you! This E46 cup holder expander will give your large size beverage a more comfortable place to rest. I have designed this one using Fusion360's shape optimization (hence the crazy design). Feel free to edit as you please and make the cup holder fit your favorite oversize mug or water bottle using the attached Fusion360 File. Enjoy. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

M3 Valve-Shim ToolC3D–01194
BMWService tools

M3 Valve-Shim Tool

I designed this valve shim placement tool to aid in my recent valve adjustment on my 2004 BMW E46 M3. After viewing the picture of this special tool online, I decided it wasn't worth the money to order one, so I purchased some magnets and printed one instead. The magnet I used is a 8mm(0.315") Diameter x 3mm(0.118") Height, and was embedded into the base during the printing stage. I used the color change feature of PrusaSlicer to stop the print before the top layer and inserted the magnet. I printed both parts out of PETG and glued them together with cyanoacrylate. The tool was tested on my engine and worked perfectly. I even did the hard to reach rear valves with this homemade tool. Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

Seat Adjustment KnobC3D–01193
BMWSeats & restraints

Seat Adjustment Knob

A Friend of mine lost one of the adjustment Knobs of his E46 Cabrio, you can buy it for the bargain of 180€, after 1h of modeling in Fusion360 the cost sank to 50ct a piece Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

Convertible Wind-Screen CapC3D–01192
BMWCabin trim, cargo & roof

Convertible Wind-Screen Cap

My wind screen mounts got old and broke off, and I don't have a wind screen. These are designed to cover up the gaping hole. Not a perfect fit but definitely good enough - it won't fall out. PETG or ABS required for a hot car. Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Facelift Kidney-Grille ClipsC3D–01191
BMWBumpers, grilles & guards

Facelift Kidney-Grille Clips

This is an updated set of Murat's clips which fit on the facelifted E46 kidney grills (My car is a 2002 325i wagon) and work without any filing / cutting / modification of the 3D printed part. How to use: Follow Murat's instructions for trimming the existing clip sockets on the kidney grill plastic (leaving ~1mm left + socket depth). Install as suggested by them (use a small flathead screwdriver or similar to pry the metal tabs of the hood into the printed groove on the clips. My printed parts are numbered and lettered to indicate where they go on the grill. How to read the number/lettering: When standing in front of the car and looking at the grill, there is a Left and Right grill. On each Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Compact Rear-Shelf Retaining ClipC3D–01189
BMWCabin trim, cargo & roof

Compact Rear-Shelf Retaining Clip

When I bought a E46 Compact it had broken rear shelf retaining clip. So whenever I opened the trunk the shelf would hang randomly in the air. Also it made closing the trunk hard, as it jammed between the trunk lid and the body of the car. So I decided to make a model of the broken shelf clip, that came with the car. It may need some sanding or filing to achieve a better fitment in the shelf steel tube. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Trunk bottom support pad (convertible/coupe)C3D–01180
BMWCabin trim, cargo & roof

Trunk bottom support pad (convertible/coupe)

I lost my cap some time ago and I found one here, but not for my model and not in design I wanted. Therefore I did model for my car. It is tested in e46 convertible, but probably will fit coupe and maybe also other models. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Oil Filter removal toolC3D–01179
BMWRemoval tools

Oil Filter removal tool

I used it for my BMW E46 and it is very sturdy. You can use a 32mm Hex Nut or a 1/2" square wrench to open the oil filter cap. The Tool on the picture was an earlier smaller version but it broke. Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E36 · 3 Series · E46