C3D–01387Hood-Roundel Mounting Clip
Prefer to use Nylon or another filament with great cohesion (My clips was printed with Nylon-GF) Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
1995–2004
Verified catalog fitment for this exact BMW generation. 50 printable parts currently match.
C3D–01387Prefer to use Nylon or another filament with great cohesion (My clips was printed with Nylon-GF) Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01386Center-compartment insert for a BMW E39, designed as a sturdier alternative to the loose factory cup holder. It fits in the storage recess directly in front of the original holders and accommodates cups up to 73 mm in diameter plus a phone up to 75 × 10 mm. Use cabin-heat-resistant material, verify the dimensions against the console, and confirm secure retention and unobstructed operation.
Fits 5 Series · E39
C3D–01385BMW E39 dashboard hole cover no glue needed(for my car it was tight fit, but not too tight) Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01378hey ho, got a couple of used AC Schnitzer type 2 rims with the center hub caps missing, so i designed a simple and clean version. may require some sanding and spraypainting afterwards to fit your rim color. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
Clip for sunblind holder BMW E38 E39 Printed ABS. Nozzle 0.2, layer height 0.01, speeds 40 - internal, 30 - external. Printing is carried out in two halves, after which it is glued together, processed mechanically and in acetone to give a presentable surface. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39 · 7 Series · E38
C3D–01352Battery-retaining spacer reproduced from BMW component 61211350825 for E30, E34, E39 and E46. BMWFans identifies it as spacer 1350825 and confirms those chassis among broader BMW usage. Match battery size, tray slot and hold-down engagement, and do not use it to compensate for an incorrect battery or damaged clamp.
Fits 3 Series · E30 · 3 Series · E46 · 5 Series · E34 +1
C3D–01393Replacement for BMW OEM part 51478230749 (Support for Tension Strap). Used to secure the trunk floor panel in BMW E39 E36 models. Printing recommendation: For maximum strength, print the part at a 45° angle using supports. This print orientation improves layer adhesion in the areas subjected to the highest load, resulting in a stronger and more durable part. BMW catalog lists support 51478230749 from 1996-09 and records bilateral interchangeability with superseded 51478197822; retain the creator-listed E36/E39 fitment. Verify dimensions against the original part and confirm full operation before regular use.
Fits 3 Series · E36 · 5 Series · E39
C3D–01392I designed these brackets because the original BMW E39 tweeter mounts are too small to fit the Gladen Alpha 130 G2 tweeters. Installing aftermarket tweeters in the factory location can be challenging, as the available space inside the original E39 mounting brackets is very limited. These adapters allow the Gladen tweeters to be mounted securely while retaining the factory installation position. Compatible Speaker Set Gladen Alpha 130 G2 Original BMW Parts Left side: 65138362527 Right side: 65138362528 OEM reference: Printing Notes Designed for BMW E39 factory tweeter locations. Tested with Gladen Alpha 130 G2 tweeters. PETG or ASA is recommended for improved heat resistance inside the vehicle. Print with at least 3 perimeters and 30–40% infill for good durability. I hope this model helps anyone upgrading the factory audio system in their BMW E39. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01391Replaces the integrated plastic tab that commonly shears off, allowing the fog light to be secured without replacing the entire bumper. The bracket replicates the factory slot geometry. Once bonded, the fog light housing slides into the bracket and locks into place using the original mounting hardware/method. Material: Would recommend ASA or ABS. Compatibility: 2001–2004 (Facelift / LCI) BMW E39 5-Series models. Will not fit Pre-Facelift or M-Sport/M5 Bumpers. I also sell the printed parts: Installation Instructions: 1. Access: Gain access to the fog light assembly either by removing the front splash guard in the wheel well or by removing the front bumper entirely. 2. Alignment: Leave the fog light attached to the bumper by its remaining intact mounting point. 3. Test Fit: Position the repair bracket and verify that it makes flush contact with the bumper surface. Ensure the circular tab on the fog light housing slots correctly into the bracket. 4. Preparation: If remnants of the broken original bracket interfere with the fitment, trim them down until the repair bracket sits flush. 5. Bonding: Thoroughly clean the contact areas on both the bracket and the bumper. Apply a strong epox Creator limits fitment to the facelift/LCI bumper. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01389BMW E39 523I glovebox nut PETG,ABS or other Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01388This speaker plate is designed for the BMW E39 speaker enclosure and replaces the original crossover filter. Allows the box be airtight when using with aftermarket speakers for better sound quality. Cable hole is designed for 2x1.5mm2 cable Hole size is: 7mm x 4mm Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01381This is the design I made to replace my broken sun visor clip in my 2000 BMW E39 528i Touring. It is a little difficult to snap in but has a nice fit once it's clipped in all the way. Some filing or sanding might fix the stiff fit. Creator reports fitment in a 2000 E39 528i Touring. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01379...trying to fit aftermarket speakers in my e39 bmw i found out that they leave a gap to the standard boxes in the front doors. so i quickly designed these simple rings to close the gap, Use TPU to print them to ensure a tight fit. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01377You probably do not use your E39 bluetooth phone anymore. Don't waste this space in your car and print my inlay to make this area useful for you. There are different versions available, I hope you will be able to chose the most fit for you;) I personally use the one with the grooves for phones. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
Ther is the Mirror cover bmw e39 latch instead broken one! For each cover you need 2 direct and 2 mirror printed parts. Just put on things to the broken parts, try to put cover on mirror (i need to cut height for 2 of them) and fix it with glue. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01369This thing was made with Tinkercad. Work In progress. For BMW Center Console Storage Coin Tray replacement. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01368Pair of reinforcement brackets for fitting a universal T2/T3 cup holder in a BMW E39. The creator reports that it supports McDonald’s drink sizes without smaller cups tipping and accepts PET bottles up to 0.5 litres. Print two brackets in ABS or PETG; PLA can deform in summer cabin heat. After printing, tap M4 threads in the holes, shorten the screws so they sit flush without protruding, and attach the brackets to the cup holder. These replace the unstable sheet-metal clips supplied with the universal holder. Verify dimensions, fastening, and unobstructed operation before regular use.
Fits 5 Series · E39
This is for all the RHD E39 owners because I couldn't find any online except LHD so I designed a new one :D When printing flip the whole thing on its bottom so it prints properly. :D Btw the pictures got squashed by the site so to see a better image view the original image by clicking the fullscreen button at the top right and then click view original image. Creator identifies right-hand-drive fitment. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01366Clip zum anschrauben der oberen Seitenrollohalter im Türrahmen. Bei BMW leider nicht im ETK zu finden. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39 · 7 Series · E38
C3D–01365My E39 Touring was missing one of the clips to hold in the plate bracket (plinth). The previous owner had used silicone to hold the panel on. Unable to live with this I contacted the dealership - who were unable to find the part in their system. Doubting their competence I checked realoem myself and actually couldn't find a part number. So I turned to Fusion360 and whipped these up. I've never designed anything before so please bear with me. I have made two revisions of this thing. **(bmw_plate_plinthe_v3)** The first is a copy of the original - fits snug and locks nicely. - It may be a good idea to use a bit of RTV or Butyl Rubber around the hole to keep water out! **(Nut.stl /Thread.stl)** The second is a threaded option. Allowing you to fit an M8x1.25 nut on the back. This option was created for people who may have corrosion around the hole thus making it too big for the snap in option. Printed these on my CR-10S w/ 99% concentric infill 5 walls and 0.12 layer height @ 35mm/s Hopefully they can be of use to someone else too. Cheers. Apparently fits these models too! BMW E30 318i M10 1.8L BMW E30 318i M42 1.8L BMW E30 318is M42 1.8L BMW E30 325i M20 2.5L BMW E30 325is M20 2.5L BM Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01359My BMW E39 wagon (touring) was missing the plastic clips at both sides of the tailgate. These clips hold the plastic side covers in place. Since the original spare parts (BMW part number: left: 51498217213, right:51498217214) are way too expensive, I have decided to print my own ones. The uploaded files contain the right side clips, but you can mirror them in Cura so that you also have the left side ones (see pictures). BMW catalog identifies the black left/right clips from 1996-09 for E39 Touring, including cataloged European/USA and LHD/RHD applications; mirror the supplied right-side model for the left. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01358My BMW E39 5 Series was missing the selection switch for the power mirror. (I don't know how the previous owner could rip that thing off...) Here you can find a custom-made replacement switch. Just push it into its place. If you have any ideas for improvement, please feel free to contact me. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01357The toolbox holding strap on my car broke in the middle due to material stress over the years. Designed a new strap with with a hinge, to prevent this from happening in the future. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39
C3D–01354This is a rear window sunshade hook for BMW E39. Verify dimensions against the original part and confirm full operation before regular use.
Fits 5 Series · E39