i3

Pair of compact brackets for hanging a JBL BassPro Nano under the rear-seat frame where the optional amplifier is not installed. The creator printed two in PETG at 50% infill, fastened them with the subwoofer's original screws, and shows the installed unit and bracket locations. Confirm the vehicle lacks the conflicting amplifier, protect wiring, use thread-safe fasteners, and verify seat movement, ventilation and secure retention before driving.

Fits i3 · I01

Anti-tip adapter for the source-linked small espresso cup, shaped for the center-console cup position. The creator shows the physical adapter seated in the vehicle and with the matching cup. Print in PETG, ABS or another cabin-heat-resistant material, verify both the cup and console fit, and keep hot liquids securely contained and clear of controls while the vehicle is moving.

Fits i3 · I01

Tool set for I01 outer-door-panel hardware: a deep and standard adjustment-element wrench plus seven clip-saver sizes for printer-tolerance matching. The creator shows the physical tools on the relevant clip and explains that the saver may recover clips that survive warm-weather panel removal. Numbers 51007355279 and 51007378101 identify the serviced clip and adjustment element, not these printed tools, so neither is assigned. Do not reuse cracked or distorted one-time clips; verify panel alignment and secure retention after service.

Fits i3 · I01

Three-piece key-fob box with a separate insert, bottom and lid, designed to prevent accidental button presses while carried in a pocket. The source shows the complete physical case closed, open and holding the I01 key fob. This is a protective accessory rather than the key housing itself. Check that the fob fits without continuously loading any button and that the lid remains secure during normal carrying.

Fits i3 · I01

Deep storage tray that replaces the obsolete phone snap-in adapter in the center armrest while retaining the existing mounting cavity. The creator designed the tray for support-free printing, recommends PETG or ABS/ASA with at least 30% infill, and shows it fitted empty and loaded as well as beside the removed adapter. No snap-in adapter or armrest parent number is assigned. Verify flush seating, secure retention and full armrest movement.

Fits i3 · I01

Organizer for multiple EV charging cards that plugs into a center-console cup-holder slot. The source shows the physical organizer installed and loaded with cards. This is an accessory rather than a serviced console component. Use PETG, ABS or another cabin-heat-resistant material, confirm a secure cup-slot fit, and keep the cards and organizer clear of adjacent controls and loose-object hazards.

Fits i3 · I01

Removable center-console cover with an integrated opening for an Apple MagSafe puck, remixed from the original storage cover. The source shows the physical cover installed and provides model views of the puck opening and underside support. It fits non-braided-cable pucks directly; braided-cable versions may require a small amount of adhesive. Use cabin-heat-resistant material, secure the puck and cable, and verify charging temperature and clearance.

Fits i3 · I01

Four-piece adjustable rear-hatch stop with a flexible buffer, modeled and trial-fitted on a 2020 120Ah vehicle to eliminate play and rattling at the closed hatch. It recreates the function of BMW adjustment element 51247361955, originally used on earlier cars, for later LCI vehicles whose lock-integrated rubber has worn. Print two assemblies as the creator specifies, use TPU for the buffer and heat-resistant rigid material for the body, screw and nut, then adjust symmetrically without preloading or misaligning the hatch.

Fits i3 · I01

Organizer for the small storage compartment below the armrest, with a rigid body, two optional flexible pads and a single-piece multimaterial variant. The source shows the physical pieces and the organizer installed both loaded and empty. Print the body in PETG or another cabin-heat-resistant rigid material and the pads in TPU; verify stable seating and unobstructed access to the adjacent 12 V and USB connections.

Fits i3 · I01

Eccentric 48 mm funnel shaped to clear the surrounding structure at the windshield-washer reservoir opening. The creator shows the physical funnel seated in the fill neck from two angles and designed it to print support-free. This is a service accessory rather than the reservoir, filler neck or cap, so no parent number is assigned. Confirm the neck fit before pouring and keep debris and incompatible fluids out of the washer system.

Fits i3 · I01

Center-console switch faceplate with an added opening for a retrofitted Dynamic Traction Control button from an i8. The source shows the ASA print installed around the complete switch bank and notes reinforced side clips. This is retrofit trim, not a stock I01 faceplate, so no switch-bank or i8 parent number is assigned. Confirm the retrofit wiring separately, use cabin-heat-resistant material, and verify button travel and clip engagement.

Fits i3 · I01

Flexible replacement tether joining the AC and DC fast-charge port caps to the inside of the charge door on CCS-equipped vehicles. The creator shows the printed strap installed on both caps and compares it with the original tether. Print in a durable UV- and weather-resistant flexible material, confirm that all ends seat fully, and check that the strap cannot foul the inlet, caps, hinge or door seal.

Fits i3 · I01