car3dparts.

Mercedes vehicle line

Vito / Viano / V-Class

Choose the precise generation for verified fitment, or browse all 32 parts currently associated with this vehicle line.

All generations

Vito / Viano / V-Class parts

Open filtered catalog →
Factory Phone-Cradle Adapter PlateC3D–01767
MercedesConsole & storage

Factory Phone-Cradle Adapter Plate

Adapter plate that replaces the obsolete factory phone cradle while reusing its original dashboard bracket and screws, with variants for a Brodit MoveClip mounting pattern and alternate screen position. Source photographs show the bracket, plate and phones installed. Match the equipped cradle and screw lengths, use cabin-heat-resistant material, and confirm the device cannot obscure instruments, controls, airbags or the driver view.

Fits Vito / Viano / V-Class · W639

Electrical Fuse-Box Latch ClipC3D–01772
MercedesEngine-bay electrical & sensors

Electrical Fuse-Box Latch Clip

Replacement latch clip for the engine-compartment electrical fuse box, identified by the creator as the exact serviced child. Source photographs compare it with the original and show it retaining the lid. Print in engine-bay-temperature-resistant PETG, ABS or nylon, verify the box and latch version, and confirm the lid seals and remains secured without pinching wiring.

Fits Vito / Viano / V-Class · W639

Speaker Adapter RingC3D–01774
MercedesInterior doors & windows

Speaker Adapter Ring

Sturdy adapter ring for fitting aftermarket speakers to the stock front-door or rear-side mounting pattern. The creator reports precise alignment with the factory screw holes and supplies installed source photographs. This is an aftermarket adapter rather than any listed speaker assembly, so no speaker OEM number is assigned. Verify speaker diameter, depth, window and trim clearance, seal against rattles and moisture, and secure wiring away from moving mechanisms.

Fits Vito / Viano / V-Class · W639

Interior Panel Retaining ClipC3D–01773
MercedesInterior doors & windows

Interior Panel Retaining Clip

Replacement push clip for interior trim panels, identified by the creator as the exact child and accompanied by an EPC-style source diagram. Print in tough cabin-heat-resistant material, compare head and stem dimensions with an original clip, use only in the stated non-structural trim position, and confirm the panel is secure without interfering with wiring, airbags or seat mechanisms.

Fits Vito / Viano / V-Class · W639

Front Air-Vent Horizontal Fin AssemblyC3D–01681
MercedesDashboard & controls

Front Air-Vent Horizontal Fin Assembly

Replacement horizontal-fin assembly for the internal front dashboard vent nozzle. The creator reverse engineered the part from a van, had it printed in nylon and used it in the left vent; the source only suggests, rather than proves, that other front vents share the same internal geometry. Match the original left-side fin assembly before use, print in tough cabin-heat-resistant material, finish the pivots without removing retention features, and confirm every fin moves freely, stays aligned and does not obstruct airflow.

Fits Vito / Viano / V-Class · W638

Dashboard Display iPad Pro HolderC3D–01846
MercedesDashboard & controls

Dashboard Display iPad Pro Holder

Two-piece holder that slides over the central Audio 20 display and carries a 12.9-inch second-generation iPad Pro in its leather case. The creator explicitly designed it for the V-Class/Vito/Marco Polo display in this chassis and instructs bonding the two printed pieces after printing. The source gives no material; PETG, ABS and nylon are listed only as conservative cabin-heat-resistant choices. Match the Audio 20 display and tablet/case dimensions, line the vehicle-display interface with textile tape as shown on the same-author follow-up, and verify the holder cannot obscure the road, controls or airbags or release the tablet under braking.

Fits Vito / Viano / V-Class · W447

Peiker-Slot MagSafe Charger InsertC3D–01851
MercedesConsole & storage

Peiker-Slot MagSafe Charger Insert

Insert replacing the Peiker phone-preparation module position between the 12 V socket and original USB/MMI panel in the centre console. The creator verified it on a V-Class with that exact console layout and warns that other Vito variants must be compared by photographs and the stated 72 × 129 × 12 mm dimensions. Use ASA as recommended, or ABS; PETG is only cautiously suggested and PLA is excluded. Fit a dimensionally compatible MagSafe/Qi charger, use an automotive DC-DC/USB-C module with a dedicated fuse, mechanically secure and insulate every wire, check charging heat under extended use, and confirm the assembly cannot interfere with controls. Electrical installation remains at the installer’s risk.

Fits Vito / Viano / V-Class · W447

Fuel-Cap TetherC3D–01764
MercedesCooling, fuel & exhaust

Fuel-Cap Tether

Flexible replacement tether for the fuel filler cap, created after the original tether failed and shown installed on the filler door. Print in fuel-, UV- and weather-resistant flexible material, preserve the cap sealing surfaces and venting, keep the tether clear of the neck and hinge, and confirm the cap still seals and locks normally.

Fits Vito / Viano / V-Class · W639

Washer-Reservoir CapC3D–01765
MercedesWipers & washers

Washer-Reservoir Cap

Flexible 74 mm replacement cap for the windscreen-washer reservoir. The creator measured the original, recommends TPU and notes that a 98% scale may improve fit; source photographs show it installed. Verify the reservoir neck diameter, print in washer-fluid-, heat- and weather-resistant flexible material, and confirm the cap seats securely without obstructing filling or venting.

Fits Sprinter · W901–W905 · Sprinter · W906 · Vito / Viano / V-Class · W639

Battery-Compartment Cover Wing NutC3D–01762
MercedesEngine-bay electrical & sensors

Battery-Compartment Cover Wing Nut

Replacement wing nut used on several battery and storage-compartment covers. Source imagery shows the installed fastener location and the loose printed geometry. Match the original thread and cover version, print in tough cabin-heat-resistant material, do not force a mismatched thread, and tighten only enough to retain the non-structural cover without cracking it.

Fits Vito / Viano / V-Class · W639

Bonnet Support-Strut ClipC3D–01761
MercedesDoors, bonnet, boot & bed hardware

Bonnet Support-Strut Clip

Replacement retention clip for the bonnet support strut. The author supplies printable STL and editable STEP geometry plus a source photograph of the physical clip. Use engine-bay-temperature- and weather-resistant material, compare the strut diameter and mounting profile, and confirm the strut is retained when stowed without weakening or interfering with bonnet support or latching.

Fits Vito / Viano / V-Class · W639

Sun-Visor Vanity-Mirror FrameC3D–01759
MercedesCabin trim, cargo & roof

Sun-Visor Vanity-Mirror Frame

Replacement frame and cover for the vanity mirror in the sun visor. The source shows the printed frame holding a mirror insert and the supplied author geometry. Reuse only safe, intact mirror material, smooth every edge, use cabin-heat-resistant material, retain the frame without stressing the visor, and confirm the cover closes securely and cannot fall into the driver field of view.

Fits Vito / Viano / V-Class · W639