Vito / Viano / V-Class W447

Insert replacing the Peiker phone-preparation module position between the 12 V socket and original USB/MMI panel in the centre console. The creator verified it on a V-Class with that exact console layout and warns that other Vito variants must be compared by photographs and the stated 72 × 129 × 12 mm dimensions. Use ASA as recommended, or ABS; PETG is only cautiously suggested and PLA is excluded. Fit a dimensionally compatible MagSafe/Qi charger, use an automotive DC-DC/USB-C module with a dedicated fuse, mechanically secure and insulate every wire, check charging heat under extended use, and confirm the assembly cannot interfere with controls. Electrical installation remains at the installer’s risk.

Fits Vito / Viano / V-Class · W447

Replacement clip joining a Rituals fragrance dispenser to the centre ventilation slats in a 2025 facelift V-Class. The creator printed and physically shows it installed, specifies PETG with 0.2 mm layers and 30% infill, and deliberately strengthened the design. Fitment is limited to the facelift centre vent and the matching Rituals dispenser back bars. Confirm both interfaces, insert without bending or scratching the vent slats, preserve airflow and vent adjustment, and remove the accessory if it loosens or obstructs controls or visibility.

Fits Vito / Viano / V-Class · W447

Cupholder-mounted charging dock remixed specifically for the 2014–2022 Vito and tested with an iPhone 12 Pro Max in a thin Pitaka Air case; the creator also states iPhone 13 Pro Max fitment. It requires a small Lightning plug such as the cited 0.5 m Apple cable, with tape used to make the plug snug, and includes a cable channel to the nearby USB port. Print in PETG as recommended, match the exact phone/case/plug and cupholder, secure and route the cable safely, and verify the dock cannot obstruct controls or release the phone under braking.

Fits Vito / Viano / V-Class · W447

Charging dock shaped for the front centre-console cupholder and an iPhone 12 in an Elago silicone case. The creator states exact Vito fitment, recommends ABS or PETG because cabin temperatures can exceed 70 °C, and notes that other cases, phones and cable plugs require geometry changes. Match the cupholder, phone case and charging connector, route the cable without pinching it, use supports as specified, and verify the dock and phone stay retained without obstructing the selector or controls.

Fits Vito / Viano / V-Class · W447

Cosmetic plug for closing the exposed holes left after removing the armrests from individual V-Class seats. The creator explicitly tags this chassis and supplies the printable child geometry and multiple CAD source views, but gives no material, seat-version, colour or long-term retention details. PETG, ABS and nylon are listed only as conservative tough cabin-heat-resistant choices. Compare the exposed seat hole and plug profile, fit without forcing the seat trim, and confirm the plug remains secure and does not interfere with seat adjustment or restraint hardware.

Fits Vito / Viano / V-Class · W447

Two-piece holder that slides over the central Audio 20 display and carries a 12.9-inch second-generation iPad Pro in its leather case. The creator explicitly designed it for the V-Class/Vito/Marco Polo display in this chassis and instructs bonding the two printed pieces after printing. The source gives no material; PETG, ABS and nylon are listed only as conservative cabin-heat-resistant choices. Match the Audio 20 display and tablet/case dimensions, line the vehicle-display interface with textile tape as shown on the same-author follow-up, and verify the holder cannot obscure the road, controls or airbags or release the tablet under braking.

Fits Vito / Viano / V-Class · W447

Multi-part Gridfinity-based replacement for the center-console cupholder and storage unit, explicitly stated by the creator to fit V-Class/Vito, C-Class, E-Class sedan/estate/coupé/cabriolet applications sharing the original insert. It reuses the original double-torsion spring, adds supported cupholder clips, and uses 6×2 mm magnets. Preserve spring orientation, secure every magnet, verify each module locks in place, and keep all contents and moving parts clear of controls. The creator identifies the exact replaced cupholder unit as A2056800691, corroborated by the official Mercedes-Benz genuine-parts listing.

Fits C-Class · W205 / S205 / C205 / A205 · E-Class · W213 / S213 / C238 / A238 · Vito / Viano / V-Class · W447