Forester Third generation (SH)

Coin holder for your Subaru Forester SH.

Fits Forester · Third generation (SH)

I was tired of there being a single large pocket in my center console. I will probably use this as a starting point for additional versions but the interfacing geometry that mates up with the existing console are all in the correct place. This should fit all SH series Subaru Foresters 2009 - 2012 Designed in Fusion 360

Fits Forester · Third generation (SH)

It never really felt right to put my round cup into the square cup holders in my Subaru so I decided to make an insert. I will probably tweak the round portion to work with different sized cups a little better but this version works great for my current coffee mug. The fit in the existing cup holder fits like a glove. Designed in Fusion 360.

Fits Forester · Third generation (SH)

Retention clip broke off form my fuse box door on my 2009 subaru forester. This is the one on the drivers side right near where your left knee would be. Printed on its side to give the bottom hinge clips some flex without breaking

Fits Forester · Third generation (SH)

The cover, plug or insert is for the transmission release whole that is usually in the upper left of the automatic shifter in the Subaru Forester. It is very similar to the Outback (Part No: 35181AG00A) however the Outback part is about half the height of the Forester Cover Release. The Cover Release is individual sold for the Outback but in order to get it for the Subaru Forester you have to buy the whole shift indicator plate (Part No: 35170FG080) for the console. It costs anywhere between $80-$125 dollars.

Fits Forester · Third generation (SH)

Subaru Forester SH 2009-12 To fit the large storage hole in the front centre dash area (below the heater controls)> I found I didn't like putting anything in there as it was always on "show" for potential thieves etc. So the idea was to have a small cubby hole with door, and then a small tray above (tray fits next to the 12v socket above the door/frame.) Works ok, is reasonable "neat" - fix in place using (a large amount of) double sided foam trim tape. PETG or ABS preferred due to heat in cars may warp PLA, but I have had success with PLA in cars, as long as not in direct light etc (which this is not). First attempt so could be improved. Dry fit and measure the position first, the frame needs to be in place first so measure vs the tray. 1mm x 6mm magnets in the lid/frame. 2mm (M2) bolts in the hinges of the lid. Feel free to modify or improve.

Fits Forester · Third generation (SH)

Centre divider for the console next to handbrake area. I lost the removable "wall" so quickly knocked this up.. Fits fine, but doesnt stack on the other divider unfortunately.

Fits Forester · Third generation (SH)

This is a simple tool for installing your Cam Oil seals flush (I got frustrated with useless install kits that pushed it in too far or not straight) This was for my Subaru Forester 2010 SOHC, it has 45 x 32 x 8.0mm cam oil seals Just tap in with a light rubber mallet, worked great Designed in Tinker CAD, which I am getting the hang of, bit by bit I used random z seam &10% support , comes out easy on PLA+

Fits Forester · Third generation (SH)

Subaru Forester SH - Door pocket bin. Fits snugly into the door pocket. Store your sweet wrappers, tickets, etc in this handy bin. Push firmly to clip into place under the angled lip of the door pocket. .stl provided is for the right side (UK drivers), if you want the left, simply mirror the model in your slicer (pay attention to which direction you mirror!). Print in PETG/ABS etc if you live in very hot climates where PLA may soften in the heat. However for the sunny UK (!) I have found PLA is perfectly fine as its mostly protected from direct sun and heat in the door (used a similar bin in my old Forester for three years no issues). 0.25mm layers, 2 perimeters, 20% infill is fine = roughly a bit less than 5 hour print per bin. Nothing crazy - an easy print. Some overhang on the opening lip but should be within the capability of most printers!

Fits Forester · Third generation (SH)

A slip - in Fuel Cap holder for Subaru Forester (SH - Gen3) This version has been strengthened with gussets as the original version (In my experience in the Aussie Heat) Warped and split with the pressure of the cap after repeated use. I remixed the version by elanaut and added the Gussets I will most likely fit other model Subarus - just look for the pressings in the fuel door like in these pictures.

Fits Forester · Third generation (SH)