Find your next part.

Replacement headlight closure-panel lock ring modeled for a 1996 Grand Cherokee ZJ. The creator identifies possible use across the 1993–1998 generation.

Fits Grand Cherokee · ZJ / ZG

Replacement transfer gear and pressure roller for the Grand Cherokee ZJ power-antenna drive. The creator installed the pair after the worn mechanism rattled and failed to extend fully.

Fits Grand Cherokee · ZJ / ZG

Replacement transfer-case shift-indicator plate and insert for the floor console used in Cherokee XJ and Comanche MJ vehicles. The blank surface can be lettered or backlit.

Fits Cherokee / Liberty · XJ · Comanche · MJ

Low-profile fog-light mount for a Wrangler JK aftermarket bumper where a winch interferes with the factory cup. It moves the original fog lamp forward approximately 13 mm.

Fits Wrangler · JK

Alloy Wheel Center Cover designed for the 1996-2001 Toyota Camry (XV20). Replacement alloy-wheel hub cover designed and fitted for a 1998 Camry. Wheel-specific

Fits Camry · 4th Gen

A printable hood-prop latch and hinge documented by the original creator for 2001 Toyota Sienna fitment. Source explicitly says 2001 Toyota Sienna and supplies both latch and hinge models.

Fits Sienna · 1st Gen

Repair set containing a bonnet-prop-rod retaining catch and a front-grille screw clip, designed from a 1987 four-wheel-drive pickup.

Fits Hilux · 4th Gen

Flexible replacement plugs for the rectangular access openings in the two-wheel-drive pickup frame.

Fits Hilux · 5th Gen

Replacement plastic captive nuts for securing the grille, headlamps and front running lights. The creator recommends weather- and heat-resistant material.

Fits Land Cruiser · 60 Series

Replacement quarter-turn retaining clip for the rear tow-hitch cover.

Fits Range Rover Sport · L320

Four-part clamp mount for attaching a Salora CDC100-style dashcam to the interior mirror. Short and tall ball-arm options are included, together with the mirror clamp and retaining nut.

Fits Freelander · 1

Two-part eyelet mount that clamps around a factory roof rail using common M8 hardware. The source recommends PETG, 20% infill, doubled infill lines, and three walls. Use only for light-duty restraint and never as a rated recovery or lifting point.

Fits Discovery · 3 · Discovery · 4

Replacement hatch pin seat receiver.

Fits 924 · 924 · 944 · 944

Replacement washer bottle cap + seal.

Fits 944 · 944

Custom windshield glass stops ( ) frame mount supports.

Fits 944 · 944

Replacement bushing for the pop-up headlight pivot.

Fits 924 · 924 · 944 · 944

Snug-fit cover for a front windshield-wiper nut.

Fits 944 · 944

Threaded plastic ball-socket end for the door-handle drop linkage. The creator says the lower opening must be threaded after printing.

Fits 924 · 924 · 944 · 944

Flexible clip-on spacer with increased retention for the thinner lower arm of a twin-arm rear wiper, keeping the paired metal arms from clacking together.

Fits 928 · 928

Plastic latching receptacle that fits into the front luggage-compartment battery bracket and receives the quarter-turn battery-cover screw plug.

Fits 911 · 996 · Boxster · 987

Flexible 74 mm replacement cap for the windscreen-washer reservoir. The creator measured the original, recommends TPU and notes that a 98% scale may improve fit; source photographs show it installed. Verify the reservoir neck diameter, print in washer-fluid-, heat- and weather-resistant flexible material, and confirm the cap seats securely without obstructing filling or venting.

Fits Sprinter · W901–W905 · Sprinter · W906 · Vito / Viano / V-Class · W639

Standard and reverse-camera variants of a registration-plate light housing, designed to compress the reused approximately 2 mm gasket against the body. The creator used nylon and states the source reference as 'A 203 802 07 56'; independent Mercedes and PartSouq evidence identifies A2038200756 as the complete CL203 lamp housing, but it is not assigned because this canonical source includes a modified camera variant and the creator's number is transposed. Compare the original housing, gasket, connector and body style, use weather- and heat-resistant material, seal against water and verify illumination, camera view and boot-lid operation.

Fits C-Class · W203 / S203 / CL203

Replacement windshield-washer-fluid reservoir cap proven by the creator on a 1999 first-generation SUV. The source reports that the original cap crumbles with age and that the replacement was printed successfully in dual-colour ABS; the colour change was made 1 mm into the print. Verify the cap profile against the vehicle before installation.

Fits M-Class / GLE · W163

Rear-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208