Find your next part.

Fixes the plastic tabs on the A Pillar that usually break when trying to remove the trim for upgrades like UHF installs

Fits Discovery · 1

Replacement flexible cap for the windshield-washer fluid reservoir filler neck on the Ford Focus MK3 1.5 TDCi, covering the 2011–2018 third-generation application. It restores the removable cover over the washer-fluid tank opening; TPU is specified for the flexible printed part.

Fits Focus · Third generation

Two-piece phone-mount assembly for the large center console in 2020-and-newer Ford Transit vans. The VHB-tape mount base supports a compatible ball-head phone holder, while the removable tray provides a cleanable storage surface and access to small objects. The holder can be adjusted toward the driver or passenger, rotated between portrait and landscape, and used without screws; the source specifies support for phones up to 3.5 inches wide.

Fits Transit · Fifth generation

Replacement passenger-seat recliner handle for the 2006 Ford Explorer, fitting the seat-back recliner mechanism. It restores the lever used to adjust the seat-back angle; one current source geometry is included. Verify fit and operation before regular use.

Fits Explorer · Fourth generation

Replacement bushing for the manual-transmission shifter reverse-lockout knob in the 1968 Ford Mustang application. The longer, thicker profile replaces worn stock bushings to improve fit, smooth operation, and durability. Nylon is the documented material; verify fit and operation before use.

Fits Mustang · First generation

Replacement rear boot/parcel-shelf bracket that clips the cargo shelf in place near the rear seats. Intended for the Ford Focus third-generation hatchback fitment represented by generation 424 (2011–2018). Replaces a broken stock bracket as a direct replacement for the failed bracket.

Fits Focus · Third generation

Reinforced load-bearing insert for the vehicle's OEM jack recess and lift point. It increases contact area for a workshop jack or lift adapter and uses structural ribs to resist shear. Recommended printing uses PETG with 100% infill and four perimeters; ABS/ASA are alternatives. Verify flush fit and inspect the print before applying a full load.

Fits Fusion · North American second generation · Mondeo · Fourth generation

Driver-side replacement clip for the mirror-mounted puddle light/lamp on 2015–2023 Mustang vehicles. It restores retention after the original clip breaks; installation involves trimming the remaining original clip, test-fitting the replacement, and optionally securing it with adhesive or epoxy. One driver-side component is included; no passenger-side version is provided.

Fits Mustang · Sixth generation

Cup-holder insert for the factory center console that replaces the standard holder after removal and stabilizes a large 32 oz bottle or drink. Fits 2004-2008 F-150 flow-through consoles and 2009-2014 F-150 consoles without the flow-through configuration.

Fits F-Series · Eleventh generation · F-Series · Twelfth generation

Slide-on clip for a vehicle sun visor that holds parking tickets or other small notes. Fits the attached Ford generation IDs, including Tourneo Custom second generation from October 2023 onward. Recommended printing uses PETG, ABS, or ASA with supports, 0.2 mm layers, and 20% infill; use heat-resistant filament and avoid direct sunlight. Use restriction: Personal use only; no commercial exploitation, including resale or mass production.

Fits B-Max · B-Max · Bronco · Sixth generation · C-Max · Second generation +29

Bezel and spacer components for installing a standard 1-DIN radio or stereo in the dashboard opening of first-generation Ford Transit Connect vehicles (2002-2013). The package includes the main radio rack and a separate stand/support component; verify the dashboard variant and test-fit before final installation.

Fits Transit Connect · First generation

A removable CD-slot phone holder for the dashboard, sized for a Realme 8 Pro measuring 163.2 × 11.8 mm and similar-sized smartphones. It includes clearance for an AUX cable and uses two M3 nuts with two M3×10 countersunk screws. Print the components separately as needed for assembly; the holder is intended to install without permanent interior modification.

Fits Fiesta · Sixth generation

Steering-wheel horn retainer ring that secures the horn ring or button to the steering wheel. Verified fitment is 1965-1966 Ford Galaxie and LTD steering-wheel assemblies. Print with supports at 100% infill in PETG; long-term durability is not established.

Fits Galaxie · Fifth generation · LTD · First generation

TPU protective boot that covers the exposed starter-motor terminal area, helping shield the cable terminals from contact and contamination. Intended for Ford Pinto starter-motor fitment for 1970–1980 vehicles; the source describes default-orientation printing without supports. TPU heat resistance was not tested.

Fits Pinto · Pinto

Full-size front grille for the Ford Sierra Mk2 Cosworth front end, supplied as two vertically split halves intended to be joined at the center; an optional screw can add stability. Use restriction: Personal use only; do not sell, reupload, modify, or remix the file.

Fits Sierra · Sierra

Rubber hood stop bumper that mounts at the radiator support to cushion and locate the hood and help prevent movement and rattling. Verified for 1992-1996 Bronco and F-150, F-250, and F-350 applications.

Fits Bronco · Fifth generation · F-Series · Ninth generation

M42 × 1.5 threaded shifter-plug set for sealed storage and transport of Type E/Rocket and Dog Box transmissions. Includes a solid cap option and a gasketed two-piece cap with a separate TPU gasket; the gasketed option helps keep dust, fluids, and gear oil out of the tail housing when the shifter is removed. Verified applications include Ford Pinto 1600/1.6/2.0/2.3, Sierra 1.6/2.0, Cortina Mk III 2.0 and Mk IV/Mk V 1.6 GT/2.0/2.3, Escort RS2000 Mk I/Mk II, Escort RS Mexico Mk II, and Mustang II 2.3.

Fits Cortina · Third generation · Cortina · Fourth generation · Cortina · Fifth generation +5

Replacement shift-lever bushing for the shift tube, supplied as closed and open geometry variants for assembly access. It restores the supported shift mechanism interface across the verified Ford applications represented by the attached generation IDs, including Taurus, Bronco, Explorer, Explorer Sport Trac, Freestar, Aerostar, E-Series, F-Series, Ranger, Expedition, and Windstar model-year ranges.

Fits Aerostar · Aerostar · Bronco · Fifth generation · E-Series · Fourth generation +23

Removable, multi-piece dashboard phone-holder assembly that mounts over the center storage-bin lid area of the European Ford Fusion dashboard while keeping the storage space available. The assembly includes a main mount, brace, reinforcing plate, USB retainer, and a three-piece spring-loaded phone cradle; print two copies of the left side panel and mirror one for the opposite side. A pair of pen springs and an external USB power module are required for the spring action and charging feature, respectively, and the assembly can be removed without permanent vehicle modification.

Fits Fusion · European

Replacement retaining pin connecting a hatchback privacy tray to the rear hatch or door. Fits the C346 application for 2012–2018 vehicles. Print laying down with supports for improved shear strength; ASA, PLA, and PETG are suitable material options, with 0.1 mm layer height reported to improve mating fit.

Fits Focus · Third generation

Cup holder that mounts over an interior door handle to hold medium and large drinks. Verified fitment is the Ford Fusion European generation (2002-2012), with an explicitly reported 2004 application. The printed body uses the door-handle interface and requires supports for the large bridge.

Fits Fusion · European

Replacement lower dashboard fader cover for the Ford Sierra/Merkur instrument-panel application represented by Ford generation 411. The package includes a blanked cover and a separate variant with a 27 mm opening for a 12 V USB socket; the source notes that right-hand-drive use requires mirroring and that the USB locking ring may need trimming.

Fits Sierra · Sierra

Printed adapter and multipart cover, spacer, riser, locking, template, and connector components for fitting a twist-attach driver-assistance rearview mirror to 2013-2019 Ford Flex vehicles. The assembly supports lane-departure warning, lane-keeping assistance, and automatic high-beam functions when paired with a compatible camera-equipped mirror and the required hardware, wiring, windshield template, and calibration. Riser styles A, B, and C are included; Style B and C use documented aluminum companion pieces.

Fits Flex · Flex

Functional replacement clip set for the rear parcel shelf of the Ford Ka Mk2 (2008–2016). Includes left and right small clip variants and larger left and right glue-on repair variants; the smaller design may require trimming, while the larger design provides more gluing area. Designed to print flat without supports; PETG or ABS are recommended.

Fits Ka · Second generation