Find your next part.

This is a printable replacement for a Subaru Impreza hood support rod end cap - or whatever you want to call the plastic part that fits into the hood slot when the rod is raised. This piece (white piece in picture) broke on our 2016 Impreza and Subaru seems to only sell the entire rod, not just the cap piece, so I decided to take a whack at modeling and printing a new one. I'm new to Fusion 360, so it took a few tries, but this one is working nicely for me. I'm not sure which other Subaru models/years this would work for, but there's not really much to it, so if it looks like the part in the picture, you can give it a shot! The part is pretty close to the original, though I did beef it up a bit in the area where the original one broke. I also set infill at 50% which might be overkill, but it seemed better to overbuild. You'll need to print with supports, and be sure to have your xacto handy to do some somewhat fiddly cleanup. I printed this using Prusament Galaxy Black PLA, mainly because it's all I have on hand, but let's face it, the engine compartment of a Subaru Impreza could use a little glittery bling, right?

Fits Impreza · Fourth generation (GJ/GP)

Lost one of my screw head covers from the door release handle of my Subaru Forest (2004). Designed this to replace, fits well, if needed use a lighter etc to soften the prongs and gently tease outwards slightly to get a better fit (secure clip). Be careful as they are delicate. Print a few at a time to give yourself spares, and also keep the print head moving allowing the tiny clips to cool between layers. Print in ABS (might be ok in PLA, just be super careful with the prongs!)

Fits Forester · Second generation (SG)

I recently blew the door speakers in my Australian 2003 Subaru Outback wagon only to find i needed to make a mount to allow the fitment of new aftermarket speakers. The following STLs will fit the three-point fitment holes in BH Outbacks 1999-2003. You'll need to print two rear and one of each front as they are angled. The door skins will fit perfectly over the mounts no problem. I printed mine in PolyMaxx at 75% infill as I wanted something solid to screw the speakers to, but that may have been overkill. No supports required. I also suggest some sort of stick on foam strip like door sealer on the face that touches the door to prevent rattles and make a better seal for bass.

Fits Outback · Second generation (BH)

None of my former cup holder dividers fit well in the Crosstrek ... so I made one that fits nicely! Added another simple half divider file.

Fits XV / Crosstrek · Second generation (GT)

Printed with 0.4 nozzle and 0.1 resolution. Infill 100% ofc. Layed on back with supports. Fits and works well.

Fits Forester · First generation (SF)

I had a first world problem: My oversized water bottle wouldn't fit in my new car cup holder. This is my solution. Print this in PETG, ABS or something with a high glass transition temperature or it WILL melt. Hope this is useful to somebody.

Fits Impreza · Fifth generation (GK/GT) · XV / Crosstrek · Second generation (GT)

I have bought white/yellow WY21W switchbacks for DRL on my 06 Outback. I do not like to see connector unprotected or covered by electrical tape. So I made simple cover that also hold resistor (M3 screw) and could by mounted with M6 bolt or ziptie. Hole for wires is sealed with hot glue / silicon sealant. On left side I had some empty holes on bracket behind batery so I could mount it with screw. On righ side I had to mount it with zip tie on back side of bracket between headlight and airbox.

Fits Outback · Third generation (BP)

This is an adapter to be used to install a Nexus 7 2013 to the center console of a Toyota86/Scion FR-S/Subaru BRZ. It has been designed using the LHD version center console of the pre facelift model of this car. Status: -printed, installed, fully tested and working Note: -The center console cover´s frame needs to be cut of for some milimeters. The design would have been possible without that, but the panel of the Tablet would sit too deep to use the full screen area for touch commands. So I dicided to go this way. Anyway, the cover is still fitting the OEM headunit with this modification in case you want to go back to the OEM headunit. -I used grey PETG for the covers and didnt perform any further treatment before installation. But it is of course possibe to change the color or surface by painting the covers. The covers can also easily be exchanged to get another color or to install another HU. Instrutions: -recommended material for printing PETG -Print the "cover_*" without supports and a layer height of 0,06mm -Print the "base_*" with the screw holes facing towards the build plate and use supports -For the "base_*" include a print pause at a layer hight of 6mm to insert a M3 hexagon nut into both screw holes. Use a glue stick and apply some glue to the upper side of the inserted nut to help the following layers to stick on it. -Cut the frame of the OEM center console before inserting of the "base_". Use the file "center_console_*" to see how the cutting has to be performed

Fits BRZ · First generation (ZC6)

On my Subaru Forester SG 2005 install is plug and play. I print it in TPU end 2019 , after cleaning looks like new ABS hold only 3 month

Fits Forester · Second generation (SG)

Got a new car and the center console didn't have an upper tray! So I looked and there was a promise of one in the works if enough orders were reached. I don't have that kind of patients. Fits my center console nicely and the finger holes make it easy to remove or route cables.

Fits XV / Crosstrek · Second generation (GT)

I designed this speaker adapter to mount a pair of hertz speakers for a friend on his Subaru Forester (model year 1997). The speakers are 165mm wide and he bought them from amazon (Hertz dcx 165). The adapter can be mounted on the front doors panel using the original screws and to link the speaker to the adapter you have to use the original screws plus one because it has four holes. To prevent vibration on the panel, it's recommended to put a little layer of insulation material on the adapter's surface that is in contact with the door's panel (as the original speaker mount). The adapter has two grooves, to pass the wires; and the higher depth of the speaker isn't a problem for the door glass (when you pull it down), it doesn't touch it. Ho progettato questo adattatore per montare un paio di speaker Hertz sulla Subaru Forester di un amico (modello anno 1997). Gli speaker hanno diametro 165mm e sono stati comprati su amazon (Hertz dcx 165). L'adattatore può essere montato sul pannello porta (portiere anteriori) utilizzando le tre viti originali e per montare lo speaker all'adattatore si possono usare le viti originali, più una dato che la cassa ha un foro di fissaggio in più. Per evitare vibrazioni e rumori, si consiglia di mettere un leggero strato di materiale isolante sulla superficie dell'adattatore in contatto con il pannello porta (come nel porta-speaker originale). L'adattatore presenta due scanalature per far passare i cavi; e la profondità maggiore dello speaker non è

Fits Forester · First generation (SF)

Subaru Forester 1996-2002 CAP-WASHER TANK Original part #86615 I lost my own and print to replace it. There are latches on the inside of the washer cap. And I also made a loop where you can tie a rope so that you don’t lose it again! :) --- Subaru Forester 1996-2002 крышка бочка омывателя. Оригинальный номер #86615 Свою я успешно где-то потерял, придумал замоделить. Внутри крышки защёлки. А также сделал петлю куда можно привязать шнурок чтобы больше её не потерять! :)

Fits Forester · First generation (SF)

Coin holder for your Subaru Forester SH.

Fits Forester · Third generation (SH)

I was tired of there being a single large pocket in my center console. I will probably use this as a starting point for additional versions but the interfacing geometry that mates up with the existing console are all in the correct place. This should fit all SH series Subaru Foresters 2009 - 2012 Designed in Fusion 360

Fits Forester · Third generation (SH)

It never really felt right to put my round cup into the square cup holders in my Subaru so I decided to make an insert. I will probably tweak the round portion to work with different sized cups a little better but this version works great for my current coffee mug. The fit in the existing cup holder fits like a glove. Designed in Fusion 360.

Fits Forester · Third generation (SH)

It's a coinbox that fits in the middle console - the console with a hatch underneath the armrest.

Fits Forester · Second generation (SG)

Retention clip broke off form my fuse box door on my 2009 subaru forester. This is the one on the drivers side right near where your left knee would be. Printed on its side to give the bottom hinge clips some flex without breaking

Fits Forester · Third generation (SH)

The cover, plug or insert is for the transmission release whole that is usually in the upper left of the automatic shifter in the Subaru Forester. It is very similar to the Outback (Part No: 35181AG00A) however the Outback part is about half the height of the Forester Cover Release. The Cover Release is individual sold for the Outback but in order to get it for the Subaru Forester you have to buy the whole shift indicator plate (Part No: 35170FG080) for the console. It costs anywhere between $80-$125 dollars.

Fits Forester · Third generation (SH)

Subaru Forester SH 2009-12 To fit the large storage hole in the front centre dash area (below the heater controls)> I found I didn't like putting anything in there as it was always on "show" for potential thieves etc. So the idea was to have a small cubby hole with door, and then a small tray above (tray fits next to the 12v socket above the door/frame.) Works ok, is reasonable "neat" - fix in place using (a large amount of) double sided foam trim tape. PETG or ABS preferred due to heat in cars may warp PLA, but I have had success with PLA in cars, as long as not in direct light etc (which this is not). First attempt so could be improved. Dry fit and measure the position first, the frame needs to be in place first so measure vs the tray. 1mm x 6mm magnets in the lid/frame. 2mm (M2) bolts in the hinges of the lid. Feel free to modify or improve.

Fits Forester · Third generation (SH)

Pull Handle OPENNER for Subaru Forester SF LH can b mirr to RH? dntknw

Fits Forester · First generation (SF)

a shortram like K&N 69 Typhoon sportairfiltersystem for SUBARU FORESTER (SG) 2.5 XT / 69-8002TS ( https://www.knluftfilter.com/69-8002ts-performance-air-intake-system ) its fittet for 100mm K&N airfilter original MAF sensor

Fits Forester · Second generation (SG)

Modified to fit a Pocophone F1 with case horizontally, other phones may required longer or shorter arms.

Fits Forester · Second generation (SG)

Centre divider for the console next to handbrake area. I lost the removable "wall" so quickly knocked this up.. Fits fine, but doesnt stack on the other divider unfortunately.

Fits Forester · Third generation (SH)

My wife drives a Subaru Impreza and her passenger sun visor broke one day. Turns out a plastic connector piece broke roughly in half. Unfortunately you can't buy just the one piece that broke, you have to spend $90 to buy a whole new visor! So to save a little money I figured I'd design a replacement part. This is specifically for a 2017 Subaru Impreza Premium Sport Hatchback. It is only for the passenger side visor, but I imagine that a mirrored version would work on the driver side visor. I have included both the Fusion360 archive and a generated STEP file so that this can easily be remixed. Apologies in advance if remixing my design is a pain, I'm still relatively new to 3D CAD and this is the most complex thing I've designed so far.

Fits Impreza · Fifth generation (GK/GT)