Find your next part.

Driver- and passenger-side belt guides that fit between the adjustable headrest and seat for inertia-reel belts. The holes accept the original rubber grommets.

Fits Spider · Series 2 (Tipo 105 / 115)

Strengthened replacement bezel that snaps onto the heated-seat control knob. The creator notes that the seat opening must be enlarged slightly for this reinforced version.

Fits 159 · Tipo 939

Replacement clip-in latch for the overhead sunglasses holder. The creator developed it through several fitting iterations and specifies ABS or nylon for cabin heat.

Fits 159 · Tipo 939

Replacement clip for a broken hinge pin on the dashboard storage-bin lid. The creator specifies 0.2 mm layers, 100% infill, side orientation and supports.

Fits Giulietta · Tipo 940

Two center-armrest storage tray variants: plain and with coin compartments. The creator recommends adding double-sided rubber inside to stop objects sliding.

Fits Stelvio · Tipo 949

Right-side replacement clip for retaining the sill/side-skirt trim. The creator specifies supports and PETG; mirror the model for the left side.

Fits 166 · Tipo 936

Prototype dashboard frame for fitting a Chinese double-DIN radio.

Fits 147 · Tipo 937 · GT · Tipo 937

Extra-deep rear headlight dust cover that provides clearance for an LED bulb or HID ballast.

Fits 159 · Tipo 939 · Brera · Tipo 939 · Spider · Tipo 939

Lower movable mounting bracket for an Alfa Romeo Stelvio headlight, designed as an alternative to the complete headlamp repair kit.

Fits Stelvio · Tipo 949

Two-piece folding grocery holder designed by Carlos Solis for the Giulia trunk. It bolts to the factory mounting location, folds out of the way, and the creator printed it in PETG for heat resistance.

Fits Giulia · Tipo 952

Left and right parcel-shelf supports designed by profpylons for the Brera. The creator printed them in nylon at 0.15 mm with supports and notes that a nozzle smaller than 0.4 mm may improve the thin features.

Fits Brera · Tipo 939

Replacement headlight alignment cup designed by Houstin Lichtenwalner for a 1985 GTV6. It works with the original screw to pull or push the headlamp during alignment. The creator reports successful versions in Taulman Bridge nylon and recommends a robust material.

Fits GTV · Alfetta GT / GTV / GTV6 (Tipo 116)

Replacement sun-visor retaining clip designed by Elek Gábor for the 147. The creator identifies original part number 735344980 and specifies ABS, supports, 0.2 mm layers, 100% infill, and side-surface orientation.

Fits 147 · Tipo 937

Replacement retaining pin designed by Mikael Tonialini for the luggage cover of a 156 Sportwagon. The creator recommends 100% infill and removing the central print support after printing.

Fits 156 · Tipo 932

Replacement cover and mounting adapter designed by Bob Gildoff after the retaining teeth failed on the door tweeters of his 1997 Spider. The creator printed both at 0.10 mm, with supports everywhere for the adapter and build-plate supports for the cover.

Fits Spider · Tipo 916

Two-piece replacement filler spout and cap designed by Giuseppe Portelli for the windscreen-washer reservoir of a 147. The creator printed it in PETG, glued the spout to the tank with cyanoacrylate, and provides an editable Fusion 360 source for tuning the attachment diameter.

Fits 147 · Tipo 937

Phone holder designed by Varsa for a 156 and mounted using a bicycle-style clamp.

Fits 156 · Tipo 932

Replacement for the small holder that retains the bonnet prop rod on a 1989 Spider. Creator trblmkr recommends PETG, ABS, or nylon because of engine-bay heat, with supports, 0.1 mm resolution, and 40% infill.

Fits Spider · Series 3 (Tipo 115)

Cup holder adapted by elec2rak to fit the side door panel of a 156, using the approximately 2 cm door-pocket gap. The creator specifies supports and 5% infill.

Fits 156 · Tipo 932

Replacement cover for the forward-collision-warning radar sensor. The creator notes that the original is easily lost and that snow or ice accumulation can make the radar sensor inoperative.

Fits Stelvio · Tipo 949

Remix of RomainCNC's magnetic phone-holder base for the central console, adding a ball for swivel holders. V1 has a 16 mm ball and V2 a 16.5 mm ball. The creator specifies ABS because PLA can deform in a sun-heated car.

Fits MiTo · Tipo 955

Adapter at the interior-mirror location for a Sony Xperia Z5 Compact phone, as identified by the creator.

Fits Giulia · Tipo 952

Replacement retaining clip for the front fog lamp. The creator identifies fitment to the 75/Milano, states the clips are no longer made, and recommends at least PETG.

Fits 75 · Tipo 162B / 161

Replacement headlamp-washer jet nozzles for the 155, created because the originals deteriorate in sunlight. The source supplies the standard nozzle and a spray variant.

Fits 155 · Tipo 167