Find your next part.

Longer repair guide for the Roadster and M Roadster seatbelt guide, independently remeasured after a shorter design moved in use. The creator reports successful PETG use and shows it installed. This is a trim guide, not a restraint anchor; confirm the belt feeds and retracts freely and never modify the belt or anchor.

Fits Z3 · E36/7 / E36/8

Two-piece cupholder and mounting insert for the rear-console slot behind the handbrake in the creator's 1999 2.5-litre Roadster. The source shows it installed. Bond or fasten the parts securely and confirm handbrake, seat and belt-buckle clearance.

Fits Z3 · E36/7 / E36/8

Wear grommet for the Roadster soft-top tension cable. It replaces only the damaged grommet, not the complete BMW tension-cable assembly 54318400951, so that parent number is deliberately omitted. Inspect the cable and top mechanism, and verify unrestricted roof travel before use.

Fits Z3 · E36/7 / E36/8

Two-piece housing and lid for the remote-key receiver when fitting a smaller replacement rear-view mirror with a compatible tri-lobe adapter. The creator reports mounting and using the replacement mirror. Secure the receiver and wiring without obstructing mirror adjustment or visibility.

Fits Z3 · E36/7 / E36/8

Replacement interior door-handle surround shown as a finished physical print from several angles. Test-fit without forcing the trim, confirm the handle returns freely, and use a cabin-heat-resistant material.

Fits Z3 · E36/7 / E36/8

Replacement headlight-switch knob that the creator printed and used after the original disintegrated. The knob body was measured from the original but the decorative cap profile was reconstructed without an original cap, so no BMW component number is assigned. It requires an M5-0.8 nut; verify positive switch operation and retention before driving.

Fits Z3 · E36/7 / E36/8

Plain and USB alternatives for the wider centre-console accessory slot. The creator reports correct fit. BMWFans identifies original cover 51162492136 from January 1997 with this generation in its applications. Dry-fit the chosen insert and secure any connector and wiring before use.

Fits Z3 · E36/7 / E36/8

Plain and microphone-opening alternatives for the dashboard switch opening. The creator reports that the cover fits correctly. BMWFans and RealOEM identify the plain cover as 51168104346 and include this generation in its applications. Confirm microphone retention and keep wiring clear of HVAC and control mechanisms.

Fits Z3 · E36/7 / E36/8

Two alternatives for the small centre-console accessory opening: a plain blank and a USB insert. The creator reports exact fit on this generation. BMWFans and RealOEM identify the original plain plug as 51168400712, introduced January 1996; dry-fit before installing any connector and keep wiring fused and clear of controls.

Fits Z3 · E36/7 / E36/8

Replacement guide bushing for the seat-drive screw where worn originals cause seat wobble. The source identifies the problem on this vehicle and shows the worn assembly and printed bushing; four are required per seat. Seat removal and disassembly are required, so isolate the battery, observe restraint-system precautions, and verify full travel and secure locking before driving.

Fits Z3 · E36/7 / E36/8

Replacement upper hook bonded to the rear seat-back trim shell. The creator modeled it from a 3D scan of the original F16 component, physically compared the printed replacement with the original, and later corrected the upper section for proper attachment. Mirror the supplied file for the opposite side. Use a heat-resistant, tough cabin-suitable material, verify the hook orientation and seat-back shell geometry before bonding, and keep adhesive and the printed part clear of seat latches, belts, airbags and folding mechanisms.

Fits X6 · F16 / F86

Dash-cubby mount for the 10.26-inch Carpuride C94 display, physically fitted and tested by the creator in a 2013 X6. This submission includes only the source's tested 2 mm support version; the later 3 mm support variant was not test-fitted and is excluded. Use a heat-resistant cabin-suitable material, confirm the dashboard cubby geometry before printing, and route the display cable without obstructing vents, controls, airbags or driver visibility.

Fits X6 · E71 / E72

Replacement retaining hook for the roller sunshade in a rear door. The creator modeled it for the fourth-generation X5, shows the printed clip next to the original, and documents it installed and holding the shade. The printed hook is intentionally slightly shorter than the original. BMW component 51 35 7 479 511 is catalogued for the G05 X5 and G06 X6 rear-door shade application, so both evidence-backed generations are linked. Fitment requires the rear side-window roller sunblind equipment; confirm door trim, shade and mounting geometry by VIN. Print in a heat-resistant automotive material and test smooth release and secure retention before road use.

Fits X5 · G05 / F95 · X6 · G06 / F96

Frame and translucent diffuser for adding a slim legroom light along the upper rear seat-back panel. The creator identifies the design for the contemporary X5 and X6, supplies separate frame and diffuser files plus a combined-print alternative, states that both parts were printed in PETG, and shows the assembly physically installed. This is an electrical lighting retrofit rather than a verified replacement for a catalogued BMW component, so no OEM number is assigned. Confirm seat-back trim geometry, wiring, fuse protection, heat clearance and secure retention before use; never route wiring through seat airbag or adjustment paths.

Fits X5 · F15 / F85 · X6 · F16 / F86

Honeycomb-pattern replacement pair for the red rear-bumper reflectors fitted to the US-market X5 M. The creator hand-measured the originals, reproduced the factory mounting features, also provides a flat adhesive-backed alternative, and documents the printed pair installed for one year. This fitment is limited to the F85 X5 M rear bumper; standard F15 bumpers and non-US configurations must be checked separately. The modeled pair replaces left reflector 63 14 7 850 005 and right reflector 63 14 7 850 006. Print in a UV- and heat-resistant automotive material, preserve rear parking-sensor clearance, and note that deleting mandated reflectors may be unlawful for road use in some markets.

Fits X5 · F15 / F85

Two-size replacement clip set for retaining the windscreen-washer hose along the underside of the hood. The creator specifies three standard clips and two 8 mm clips for the second-generation X5, and provides both an installed hood view and loose physical prints. Print in a heat-, moisture- and fatigue-resistant material, compare each clip and hose diameter with the originals, route the hose without kinks, and confirm clearance before closing the hood. No OEM number is assigned because BMW public catalogs do not establish these modeled clips as separately serviced child parts; hose and nozzle parent assemblies are deliberately not used.

Fits X5 · E70

Replacement blanking plate for the center-armrest storage opening after removal of the factory telephone cradle. The creator modeled it for the second-generation X5, shows it physically fitted and states that the friction-fit print replaces BMW cover 51 16 9 115 083 without reproducing the original clips. BMW catalog evidence also lists that cover for the contemporary X6 E71/E72. Confirm the telephone/storage-console configuration and applicable option equipment by VIN, use a heat-resistant material, and verify that the plate remains secure without interfering with adjacent wiring or sockets.

Fits X5 · E70 · X6 · E71 / E72

Replacement upper carpet-retaining clip for the left luggage-compartment first-aid-kit recess. The creator identifies the design specifically for the second-generation X5, calls for two clips and documents physically printing it in PLA. Because the archived source provides CAD views rather than an installed comparison, verify the prong spacing, panel thickness and secure retention against the surviving clip before use; prefer a heat-resistant automotive material. No OEM number is assigned because the exact serviced clip identity is not established from the source.

Fits X5 · E70

Replacement cap for the roof-rack system pictured by the creator, explicitly identified for first- and second-generation X5 applications. The source includes a physical printed cap and vehicle/rack context, but does not establish that every factory or aftermarket rail and crossbar profile uses the same interface. Compare the mating profile and dimensions with the missing cap, print in a UV-, heat- and weather-resistant material, and confirm secure retention before driving. No OEM number is assigned because the exact rack variant is not independently established.

Fits X5 · E53 · X5 · E70

Replacement rear access cover for the high-beam bulb opening on facelift headlamp assemblies. The creator replicated a perished cover from a 2005 vehicle, physically printed the replacement in ABS and reused the original rubber seal. Public BMW catalog evidence identifies the serviced high-beam cover as 63 12 6 940 252 for facelift E53 headlamps. Use only on matching 10/2003-on headlamp assemblies, transfer an undamaged seal, use heat-resistant material and confirm a dry, secure seal before driving.

Fits X5 · E53

Replacement trim sleeve surrounding the interior door-lock pin. The creator modeled it as a solid, friction-fit alternative to the original slotted piece, physically compared the print with the original and shows it installed in the door top. It corresponds to BMW locking-button cover 51 41 8 408 567, used on front and rear E53 door trims. Print in a UV- and heat-resistant material, compare the sleeve and pin travel with the original, and ensure the lock pin moves freely before use.

Fits X5 · E53

Tapered adapter for mounting an aftermarket frameless Plateholder bracket to the original front bumper mounting surface. The creator designed it for a short German plate after removing the wide factory plate carrier and shows the printed adapters installed on the vehicle. Print one adapter for each attachment point, use suitable exterior-grade material and hardware, and confirm bumper style, plate dimensions, local visibility rules and secure retention before road use. This interfaces with aftermarket hardware and is not assigned a BMW OEM number.

Fits X5 · E53

Two-piece replacement dust cover for the steering-gear input shaft. The creator designed it specifically for the first-generation X5 steering rack and shows the printed cover installed around the shaft without removing the steering assembly. Print in a heat-resistant, tough material, secure the two halves as shown by the source, and verify full steering travel, shaft clearance and attachment security before driving. BMW does not catalog this input-shaft cover as a separately serviced child part, so no OEM number is assigned.

Fits X5 · E53

Replacement retaining clip for third-party winter floor mats. The creator designed and physically printed it after the supplied clip broke, and explicitly states it was used for the mats in a BMW X4 G02. Although G20 and G03 are suggested by the source, those fitments are not independently tested and are intentionally not linked. This is not represented as a genuine BMW component and no OEM number is assigned. Use a durable material such as PETG, ABS or nylon, compare the mating profile with the broken mat clip, and confirm that the mat is securely retained without interfering with pedal travel before driving.

Fits X4 · G02 / F98