Find your next part.

Replacement upper outer plastic cover for BMW E21 Recaro seats. Mirror the geometry for the opposite side. BMWFans identifies 52101877057 as left and 52101877058 as right across E21 variants; verify seat type, side and mounting points before fitting.

Fits 3 Series · E21

Adapter for fitting most 6.5-inch speakers at the factory 4×6 rear-shelf positions of a 1981 BMW E21 320i without cutting new holes. The creator reports successful physical fit and sound. Check magnet depth, shelf clearance, fastener security and wiring before installation.

Fits 3 Series · E21

Replacement expanding nut for securing front trim, grille and valance pieces on the BMW E21. The creator physically fitted the part and recommends flexible, heat-resistant PETG at full infill. Confirm hole diameter, screw engagement and trim retention.

Fits 3 Series · E21

Printable M-Technic-style shift-knob replica documented for BMW E21 and E30. The source shows a finished physical print and provides sanding and polishing instructions. Verify selector-shaft engagement and secure retention before driving; this is not represented as an original BMW component.

Fits 3 Series · E21 · 3 Series · E30

Working replacement retaining clip for the manual window crank of a 1982 BMW E21 320i. The creator reports the reinforced full-base iteration stays installed; other E21 crank variants were not claimed. Print solid and verify positive crank retention before use.

Fits 3 Series · E21

Replacement clip for BMW door-sill/entry trim panels. The creator explicitly lists E21, E30, E36, E39, E46, E81/E82/E88, F20, E85 and related applications and identifies genuine BMW clip 51471840960. Verify the receiving-hole and trim thickness before fitting.

Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 3 Series · E21 +5

Replacement stand-off spacer for fitting AUTOID rear carbon-fibre wheel-arch extensions to the BMW G42 M240i. The source is specific to that aftermarket arch kit and does not establish G87 fitment. Print in ASA, ABS, nylon, or another exterior-grade heat- and weather-resistant material, and verify the 12.4 mm diameter, 26.05 mm height, fastener engagement, arch alignment, and wheel/tyre clearance before road use.

Fits 2 Series · G42 / G87

Round organizer insert designed specifically for the factory cup holder in BMW F44 2 Series Gran Coupe models. It provides five coin slots, a BIC-lighter pocket, and an open storage compartment. The creator recommends PETG for cabin heat resistance; verify the approximately 80.4 mm outside diameter against the vehicle before printing.

Fits 2 Series · F44 Gran Coupe

Short adapter ring that centers narrow energy-drink cans in the factory cup holder of BMW F45 Active Tourer and F46 Gran Tourer models. The creator physically tested the reduced-height ring and photographed it installed.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Flexible replacement for BMW rubber buffer 51466967605, creator-tested on an i3 and catalogued for F45, E81/E87, F20/F21, I01, and X1 E84. Print in approximately 85A TPU and cut out the temporary support tab after printing. Within the combined E8x generation, documented fitment is E81/E87 only.

Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 2 Series · F45 / F46 Active / Gran Tourer +2

Organizer tray for the compartment beneath the armrest in right-hand-drive BMW F45 Active Tourer and F46 Gran Tourer models. The source photograph shows the printed tray installed; this fitment is RHD-specific.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Four support-free mounting-base variants that clip into the small center-console storage pocket of BMW F45/F46 models. Includes fixed and rotating plates; rotating versions use an M5 nut and 12–20 mm bolt. Use PETG, ASA, or ABS rather than ordinary PLA.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Replacement hook that retains the cargo cover in position on the BMW F45 2 Series Active Tourer. Creator photographs show the physical hook installed; compare mounting orientation and clearances before fitting.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Replacement linkage between the rear center-console vent thumbwheel and airflow flap on BMW F45/F46 Active Tourer and Gran Tourer, including pre-LCI and LCI. Remove the vent assembly for access, verify linkage orientation, and use a cabin-heat-resistant material.

Fits 2 Series · F45 / F46 Active / Gran Tourer

Cup-holder extension designed and physically installed in a BMW F22 2 Series to move large 32-ounce cups clear of the dashboard while retaining the original recess as small-item storage. Plain and roundel variants are included. The creator reports good retention with a small shim and uses heat-resistant PETG-CF. Verify fit, cup stability, and clearance from controls before driving.

Fits 2 Series · F22 / F23 / F87

Cup-holder insert for 250 ml beverage cans in BMW F22 and F87 interiors. The creator uses the matching design in an F87 M2 and provides installed physical views. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the can remains stable without obstructing nearby controls.

Fits 2 Series · F22 / F23 / F87

Cup-holder insert for 330 ml beverage cans in BMW F22 and F87 interiors. The creator uses it in an F87 M2 and shows both the empty insert and a can seated in it. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the can remains stable without obstructing nearby controls.

Fits 2 Series · F22 / F23 / F87

Replacement slider for the factory BMW wireless-charging cradle that increases usable phone length to approximately 168 mm. The creator documents F2x, F3x, F8x, and I01 cradle compatibility and shows the printed part installed and measured. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material; verify latch engagement, charging operation, and secure phone retention before driving.

Fits 1 Series · F20 / F21 · 2 Series · F22 / F23 / F87 · 3 Series · F30 / F31 / F34 / F80 +2

Round and splined clutch-alignment tool variants designed for BMW N55 cars with the GS6 manual transmission. The creator printed the tool for a 2015 F22 M235i clutch replacement and verified the splined version during installation. Source fitment also names N55 E82, E9x, F3x, F10/F11, and F22/F23 cars. Use only on the specified engine/transmission combination, compare pilot and spline dimensions before use, and do not treat the printed tool as a torque-bearing service tool.

Fits 1 Series · E81 / E82 / E87 / E88 · 2 Series · F22 / F23 / F87 · 3 Series · E90 / E91 / E92 / E93 +3

Cup-holder insert developed and physically used in a 2016 BMW M2 F87 to keep narrow bottles upright. The source shows the printed insert installed beside a bottle. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the bottle remains secure without obstructing nearby controls.

Fits 2 Series · F22 / F23 / F87

Drop-in organizer tray for the deep center-armrest storage compartment of the BMW 1 Series F70 (2024 onward). Dedicated sections hold coins, keys, charging cables, and a French motorway toll tag. The creator's photographs show the printed organizer installed in the armrest and loose for inspection. Use a cabin-temperature-resistant material and confirm that the armrest closes and latches normally without pinching cables.

Fits 1 Series · F70

Custom-fitted charging pad for the center-console storage recess of the BMW 1 Series F70 (2024 onward). The creator shows the finished pad, its underside with the charger electronics, and the completed installation in an F70. It requires an INIU 15 W Qi charger, careful disassembly, and a shortened USB-C lead soldered to the charger PCB. Use a heat-resistant material, have the electrical work performed by a competent person, insulate and strain-relieve all connections, and stop use immediately if the charger or phone overheats.

Fits 1 Series · F70

Cup-holder phone stand with a Lightning-cable passage, documented by the creator for BMW F20 1 Series and F30/F31 3 Series interiors. The gallery shows the stand installed, holding phones, and routing the charge cable. Add a thin foam or rubber liner as suggested, use a heat-resistant cabin material, and confirm secure phone retention before driving.

Fits 1 Series · F20 / F21 · 3 Series · F30 / F31 / F34 / F80

Adapter that clips around the BMW F20 center ventilation grille and accepts the creator's screw-mounted phone cradle. Multiple source photographs show the current revision installed. Use ASA, ABS, nylon, or another high-temperature material; inspect the clips for cracking and ensure the phone does not obstruct controls, airbag deployment, or driver visibility.

Fits 1 Series · F20 / F21