Find your next part.

EDITED! THIS IS THE ACCURATE MEASUREMENTS. FITS PERFECT! LxBxH 30x15x20mmm Broke some clips when i took down some of my headliner, and could not find any so i made drawn and made some. Clips for headliner in BMW E60 an E61. Creator states the revised dimensions fit perfectly after replacing the earlier version. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

This is the buffer that the arm on the boot/trunk hits to stop it opening too far, if it cracks (which it will) then ultimately it tries to bend the gas struts. Photo shows a broken one and the print. This is for the RHS looking at the rear of the vehicle. The LHS is identical but mirror image. Print this so it stands on the long edge (hole and pin are horizontal) or the the arm will seperate the layers, there is a lot of force there. I used PETG at 100% infill. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

I wanted 16,5cm speakers in the roof of my e39 touring. So I designed an adapter, thought other would want to do the same The hole pattern in the roof is slightly nonsymmetric so you'll have to print a mirrored version as well Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

My BMW E39 was missing some fan grille parts for the rear seats. The CAD drawings have the exact same size as the original parts. So it just depends on how accurate your printer is (I had to sand down some areas). As you can see in the pictures you will also need a small piece of sheet metal that acts as a spring. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Update: Few of those broke using PLA 0.8 width, infill 10-25%. I suggest you print with 3 layers width (or more?). I will do a redesign to fix the weak point from printing prescriptive. This is my design for BMW floor mat holder (E36 E46 E38 E39) . Top part fits nice and works like a charm. I would say it even holds better than original one. As for the washer (bottom one) I haven't got it in real life so I've designed whatever I thought was suitable. Tested with PLA. Lay it down to print upside down. For now tests are held only in V1 version. Version 1: - Design created. Printed with CURA supports Version 2: - Added supports included in file. Gap is 0.15mm - Redesign of top part "head" - Added washer BMW part number (exemplary) 51478116564 51478183027 51478183028 51478183029 51471881521 Only the creator-tested V1 fastener is retained; the untested V2 washer and supported variant are excluded. Verify dimensions against the original part and confirm full operation before regular use.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E39 +1

Left/right interior mounting pod for adding tweeters in a BMW E28. The photographed print is installed in the car; the opening is intentionally generic, so select a tweeter that fits or design a separate driver adapter. Confirm mirror-image orientation, trim contour, sight lines and airbag-free mounting location before drilling or fastening.

Fits 5 Series · E28

Vent support for a Quad Lock phone interface, physically demonstrated on the right-hand-drive driver's-side center vent shared by the creator-listed BMW F30, F31 and F32. Fitment is limited to those bodies and RHD placement; F33/F36 and LHD fitment are not inferred. Use cabin-heat-resistant material, tighten without damaging the vent, and verify full vent, display, control and sightline clearance before driving.

Fits 3 Series · F30 / F31 / F34 / F80 · 4 Series · F32 / F33 / F36 / F82 / F83

Adjusted the model for it to fit perfectly without cutting imporant parts of the car. Only thing to remove is the bracket where the electrical conntection for the ashtray connects to. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Shift knob designed for e90 but may fit others. Clips on and does not rotate (careful of breakage if you try to twist it!) Fits fine, but is a bit light. Would be a nice print in transparent colors. Difficult to remove without breaking the teeth! (the knob teeth not yours) Please share your makes :) Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Replacement air-intake suction tube for 1999-2001 E46 M52 models, physically installed by the creator. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW component 13711438768 for the matching E46 320i/320Ci, 323i/323Ci and 328i/328Ci applications. Print in a heat-resistant engine-bay material and verify sealing and clearance.

Fits 3 Series · E46

Replacement inner translucent rocker for the BMW E36 power-window switch, physically compared with the original switch. The listed 61318365300 identifies the complete switch assembly, not this printed insert, so no OEM number is assigned. Use heat-resistant translucent material and verify return, illumination and anti-pinch operation.

Fits 3 Series · E36

Replacement sliding jaw for E30 and E28 sunroof mechanisms, copied from the original and physically compared. The source provides a load-oriented two-piece print option; BMWFans confirms sliding jaw 54121933550. Verify full sunroof travel before road use.

Fits 3 Series · E30 · 5 Series · E28

Left and right repair tabs for cracked E30 instrument-cluster mounting ears, test-fitted against an intact cluster and documented for screw or adhesive installation. Align the tabs in the dash before removing the damaged originals.

Fits 3 Series · E30

Cup-holder extension designed and physically installed in a BMW F22 2 Series to move large 32-ounce cups clear of the dashboard while retaining the original recess as small-item storage. Plain and roundel variants are included. The creator reports good retention with a small shim and uses heat-resistant PETG-CF. Verify fit, cup stability, and clearance from controls before driving.

Fits 2 Series · F22 / F23 / F87

Jeep Commander mounting set for attaching a compatible MOLLE organizer panel behind a front seat. The set includes the headrest bracket, lower connector, and retaining pin; M4 x 35 mm screws and 5 mm elastic cord complete the installation.

Fits Commander · XK / XH

Replacement socket-hinge piece for a broken Jeep Renegade sun visor. The creator printed the working part in PETG and documents it installed.

Fits Renegade · BU

Press-fit extender for the Jeep Renegade rear luggage-cover support. It increases engagement so the cover does not fall when the opposite side is being hooked in place.

Fits Renegade · BU

Two-piece front-bumper retainer modeled from the fastener on a 2000 Grand Cherokee WJ. The creator verified the installed function and oriented the insert for layer strength.

Fits Grand Cherokee · WJ / WG

Rigid MOLLE/PALS panel for the 1996–1998 Grand Cherokee ZJ center console. Standard and no-spacer versions are included, with the installation sequence and finished use documented.

Fits Grand Cherokee · ZJ / ZG

Replacement square peg for the Grand Cherokee ZJ headlight-adjustment mechanism.

Fits Grand Cherokee · ZJ / ZG

Taller replacement button for a Cherokee XJ roof-rack rail. The revised height and outer-face recess correct rocking seen with the earlier geometry.

Fits Cherokee / Liberty · XJ

Replacement hood-prop rod holder for RENIX-era Cherokee XJ and Comanche MJ vehicles. The creator does not claim fitment on 1997–2001 Cherokees.

Fits Cherokee / Liberty · XJ · Comanche · MJ

Two-piece puller for removing a seized AW4 automatic-transmission neutral-safety switch without prying on it. It uses an M8 nut and bolt to draw the switch from its shaft.

Fits Cherokee / Liberty · XJ

Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.

Fits Wrangler · JK