car3dparts.

The parts catalog

Find your next part.

Find your fit. Download a free file or choose a maker to print and ship your part.

Reset

260 matching parts

Free files. Made for your car.
Rear Window-Regulator BushingC3D–01339
BMWInterior doors & windows

Rear Window-Regulator Bushing

Two-piece repair bushing for the riveted rear window-regulator slider used on BMW E32, E34 and E36. The creator built it for a personal repair so the original rivet can remain in place, and retained the two halves with friction plus an O-ring. Inspect the regulator, lubricate the guide correctly and confirm smooth glass travel before refitting trim.

Fits 3 Series · E36 · 5 Series · E34 · 7 Series · E32

Cabin-Filter Housing Front MountC3D–01292
BMWEngine & intake

Cabin-Filter Housing Front Mount

Use ABS preferably but it wont get that hot up top where this print is located so anything will work Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

M52 Air-Intake Suction TubeC3D–01215
BMWEngine & intake

M52 Air-Intake Suction Tube

Replacement air-intake suction tube for 1999-2001 E46 M52 models, physically installed by the creator. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW component 13711438768 for the matching E46 320i/320Ci, 323i/323Ci and 328i/328Ci applications. Print in a heat-resistant engine-bay material and verify sealing and clearance.

Fits 3 Series · E46

Door and Fender Moulding ClipC3D–01139
BMWBody panels & exterior trim

Door and Fender Moulding Clip

Replacement E30 exterior door and fender moulding clip. The creator reports that the imperfect reproduction holds tightly. Listed numbers 51131953927 and 51131965105 identify parent moulding assemblies, so no OEM number is assigned.

Fits 3 Series · E30

Late-Model Headlamp Adjusting-Screw PartsC3D–01109
BMWExterior lighting, cameras & sensors

Late-Model Headlamp Adjusting-Screw Parts

Two replacement plastic pieces for the late-model E30 headlamp adjusting screw, copied from the originals and shown assembled on the screw. BMWFans confirms adjusting screw 63121385397. Form threads carefully and verify beam adjustment and retention.

Fits 3 Series · E30

2.5 mm Watertight-Terminal Repair ShellsC3D–01115
BMWEngine-bay electrical & sensors

2.5 mm Watertight-Terminal Repair Shells

Straight and 90-degree two-piece shells for repairing disintegrated 2.5 mm watertight terminals on BMW E30, E36 and E46. The source shows completed physical connectors. Bond with suitable RTV and verify terminal lock, polarity, insulation and sealing.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46

Clip-In Gear Knob SetC3D–01335
BMWConsole & storage

Clip-In Gear Knob Set

Four clip-in replacement gear-knob shapes for the BMW E34 and the creator-listed classic BMW chassis. The design was developed around the common BMW latching stem and includes an installed physical example. Confirm the lever's clip profile and preserve full shift travel before driving; the grouped API fitments reproduce only chassis families explicitly listed by the creator.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E30 · 3 Series · E36 +14

RHD Quad Lock Vent MountC3D–01317
BMWDashboard & controls

RHD Quad Lock Vent Mount

Vent support for a Quad Lock phone interface, physically demonstrated on the right-hand-drive driver's-side center vent shared by the creator-listed BMW F30, F31 and F32. Fitment is limited to those bodies and RHD placement; F33/F36 and LHD fitment are not inferred. Use cabin-heat-resistant material, tighten without damaging the vent, and verify full vent, display, control and sightline clearance before driving.

Fits 3 Series · F30 / F31 / F34 / F80 · 4 Series · F32 / F33 / F36 / F82 / F83

M-Sport Front Tow-Eye CoverC3D–01246
BMWBumpers, grilles & guards

M-Sport Front Tow-Eye Cover

Replacement tow-eye opening cover for the E46 M-Sport front bumper, refined through several physical prototypes and shown installed. The creator notes that standard SE geometry does not fit this bumper. Use exterior-rated material and verify secure retention without obstructing the tow-eye opening.

Fits 3 Series · E46

Dashboard Button-Strip USB HolderC3D–01237
BMWDashboard & controls

Dashboard Button-Strip USB Holder

This is a custom USB holder designed to replace the button blanking strip on a BMW E46 dashboard – the one next to the ASC/DSC button. It’s a remix of another model, but with serious upgrades: ✅ Now with 3 Holes : I added a third port so you can mount a standard car charger PCB . Just remove the plastic casing and drop in the board. Works perfectly with generic AliExpress/Amazon 12V USB chargers. 🔩 Rear Clamp with M3 Bolts : The back has a clamp system for a solid hold using M3 bolts and heat-set inserts (not required, but highly recommended). 📐 Includes STEP File : I reverse-engineered the original STL in Fusion 360 and included a clean STEP file for anyone who wants to customize it further Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Ashtray Storage insertC3D–01236
BMWConsole & storage

Ashtray Storage insert

Inserts into the stock E46 ashtray, should be friction fit. I included all of my files, with the following features: .stl with the holder cutouts intended for my own use, Hörmann Garage Door Opener, a ISO/IEC 7810 ID1 cutout and a generic one to use the remaining space .step without cutouts for your own modifications .f3d so you can look at my bad modelling skills and also make your own modifications I would recommend to print this in ABS, PETG may be fine but PLA will 100% shrink if your car heats up. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Windshield Cowl Seal RepairC3D–01217
BMWWipers & washers

Windshield Cowl Seal Repair

Cut off the remains of the rubber part on your windshield cowl and attach these printed ones. OEM PART: 51718208483 Mirror the end part to use it on the other side. Print multiple mid parts to cover the entire length. Printed from Fillamentum Flexfill 89A. Using 0.15mm layer height is important as there is a steep overhang on the part, which wouldn't print well using thicker layers. The end part might not fit perfectly but it did the job already so I didn't tweak it anymore. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Kidney Grill Clip ReplacementC3D–01178
BMWBumpers, grilles & guards

Kidney Grill Clip Replacement

Mounting clip replacement for the BMW E46 kidney grill. The kidney grills are held in place in the bonnet through flexible lips, which become brittle with time and heat exposure. My car is 14 years old and the kidney grills had lost their grips a while ago and were about to fall over. The quick fix was to string them up from the inside, but hardly an elegant fix for a BMW! Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Hood-Release LeverC3D–01123
BMWDashboard & controls

Hood-Release Lever

Short reinforced replacement lever for the brittle E30 hood-release handle, physically installed with a 4 mm or #8 screw and locknut. Print solid around the pivot and confirm reliable hood release before closing the hood.

Fits 3 Series · E30

Touring Boot-Lid Umbrella MountC3D–01304
BMWCabin trim, cargo & roof

Touring Boot-Lid Umbrella Mount

Two-piece open- or closed-loop umbrella mount demonstrated on the inside of an F31 Touring boot lid. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

Dashboard Trim Retaining ClipC3D–01278
BMWDashboard & controls

Dashboard Trim Retaining Clip

The dashboard panel around the start button in my e92 began falling off due to a failed clip. I left it like this for quite awhile then the passenger door wood panel also fell off so I decided to design both clips to replace the broken ones as they cost more money than im willing to pay for original and aem ones dont last one use. I printed them with support on their sides so the opening is going up and down as this doesnt rely on layer adhesion for strength. "dash clip 1" is the dash clip "clip 3" is the door clip Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Power-Window Switch Inner RockerC3D–01171
BMWDashboard & controls

Power-Window Switch Inner Rocker

Replacement inner translucent rocker for the BMW E36 power-window switch, physically compared with the original switch. The listed 61318365300 identifies the complete switch assembly, not this printed insert, so no OEM number is assigned. Use heat-resistant translucent material and verify return, illumination and anti-pinch operation.

Fits 3 Series · E36

Floor-Mat Retaining FastenerC3D–01353
BMWCabin trim, cargo & roof

Floor-Mat Retaining Fastener

Update: Few of those broke using PLA 0.8 width, infill 10-25%. I suggest you print with 3 layers width (or more?). I will do a redesign to fix the weak point from printing prescriptive. This is my design for BMW floor mat holder (E36 E46 E38 E39) . Top part fits nice and works like a charm. I would say it even holds better than original one. As for the washer (bottom one) I haven't got it in real life so I've designed whatever I thought was suitable. Tested with PLA. Lay it down to print upside down. For now tests are held only in V1 version. Version 1: - Design created. Printed with CURA supports Version 2: - Added supports included in file. Gap is 0.15mm - Redesign of top part "head" - Added washer BMW part number (exemplary) 51478116564 51478183027 51478183028 51478183029 51471881521 Only the creator-tested V1 fastener is retained; the untested V2 washer and supported variant are excluded. Verify dimensions against the original part and confirm full operation before regular use.

Fits 3 Series · E36 · 3 Series · E46 · 5 Series · E39 +1

N55 Dynamic Air ScoopC3D–01298
BMWEngine & intake

N55 Dynamic Air Scoop

Front intake air scoop for N55-powered BMW F30/F31 335i, F32-series 435i, F20/F21 M135i and F22/F23/F87 M235i/M2 applications listed by the creator. Use heat- and exterior-rated material and verify secure retention and unobstructed intake airflow before driving.

Fits 1 Series · F20 / F21 · 2 Series · F22 / F23 / F87 · 3 Series · F30 / F31 / F34 / F80 +1

Sunroof Wind-Deflector Stop RepairC3D–01275
BMWCabin trim, cargo & roof

Sunroof Wind-Deflector Stop Repair

Hello, does your sunroof deflector make a weird noise or doesn't allow your sunroof to close sometimes. Well a section of it may be broken. Both of the side stoppers on my deflector were broken so i printed a replacement pieces. Supports are needed, i used roof support as well. Replacement part for OEM BMW handle. Part Number: 54107157449 Supersession(s): 54-10-7-157-449 This product fits 60 vehicle variants. BMW: 11 models, 60 variants between 2004 and 2012. BMW E90 Slipstream Deflector Replacement Clips/Stoppers 2004-2012 by blackjet123 is licensed under CC BY-NC-SA 4.0 CC Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Non-iDrive Console Cup HolderC3D–01269
BMWConsole & storage

Non-iDrive Console Cup Holder

So I was looking for a fitting cupholder for my BMW E90 tray and couldn't find one which wasn't too big. This one fits to your BMW E90 without the big navi and without the iDrive knob. I made 3 versions which can fit 250ml, 330ml or 500ml cans (Germany/EU). With the big one, the walls might get too thin, read below. It fits very good to the tray, I use it everyday. This was designed to be printed with PLA, if you use ABS you might upscale it. Also, you can print it on the flat surface with my tag without supports. If you like the design, leave a tip :) *** Update 27.06.20 Someone requested a wider hole (currently 57mm) for norwegian 500ml cans. Uploaded another version with 66mm. Walls get very thin and cut, NO guarantee for good results as I won't try it! *** Update 11.07.20 Was shopping a german/EU 330ml can and couldn't fit it. So I made the hole slightly wider (59mm) to fit these. Ha Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93