Find your next part.

Storage-tray set for the center-console recess in BMW E60 and E61 models. Variants include a blank tray for customization, the creator’s everyday layout, a three-coin layout, and a tray for a Hörmann HS M 2/4 garage-door remote with an additional small compartment. The creator reports that the tray fits the existing console recess well. The demonstrated print used Fiberlogy Impact PLA; PETG is also suitable, while ordinary PLA is not recommended for vehicle-cabin temperatures. Verify dimensions, secure retention, and unobstructed operation.

Fits 5 Series · E60 / E61

the bmw e60 vents were very floppy and i went to see what was wrong and some how that small piece in my vent was the whole reason my vents wernt standing straight and working i found one of them so i could design these pieces 1-1 as the original i printed this in bambu black carbon fibre fillament Measured one-to-one from the original clip to restore a loose rear center vent. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Cable holder for 7mm hole. Printed without brim. Creator documents the printed holder on an E61 door harness and specifies a 7 mm mounting hole. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

This part is a small storage cubby for use in place of the broken center console ash tray for BMW E39. The bottom clip of the ash tray holder is commonly broken on E39 models and cannot be fixed without replacing with a working center console trim piece, which can be hard to find in good condition. The part includes a cutout for the illumination strip so the cubby is illuminated at night. Fitment is very tight to avoid the use of adhesives. Carefully press in with a bit of force and it will fit as shown in the photos. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Print without support, use flexible material (TPU, PBT etc.) Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Front tow hook cover for BMW E39 vehicles with pre-facelift bumper (1995 to 2000). *Normal PLA is not suitable for this application. Source specifies 1995-2000 pre-facelift bumper and warns against PLA. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Replacement roof hook for the accessory rear roller sunshade used on BMW E28, E30 and E34. It was reproduced from an original part and physically installed. BMW accessory number 82129413178 identifies the discontinued black two-piece roof-hook set; 82129413177 is the different white lower-hook style. Confirm headliner mounting, accessory configuration and color before fitting.

Fits 3 Series · E30 · 5 Series · E28 · 5 Series · E34

Replacement cap for the windshield-wiper arm retaining nut on BMW E28 and E30. The creator reproduced the current shape from an original part and reports a perfect fit. BMW number 61611370387 is the black covering cap, used on the passenger side of LHD cars and driver side of RHD cars in the creator's application; confirm side, arm style and production date by VIN.

Fits 3 Series · E30 · 5 Series · E28

Replacement center retaining clip for the sun visor of a BMW E12 520. The creator physically fitted the part and recommends PETG, ASA, ABS or another cabin-heat-resistant material; PLA can deform in summer. BMW catalogs identify the equivalent ivory holder as 51161870863, superseding 51161820684; the photographed black print is a user-selected reproduction color, not an OEM color claim. Production date and trim variants can differ, so compare the two-hole base and visor-rod diameter before fitting.

Fits 5 Series · E12

Contour spacer demonstrated with aftermarket side repeaters on BMW bodywork. The creator lists E36 from October 1996, E46 sedan/Touring, E60/E61, E81/E82/E87/E88 and E90–E93 applications. Test one side before mirroring and verify the repeater remains weather-sealed and positively retained.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E36 · 3 Series · E46 +2

Dimensioned replacement glovebox damper pin for BMW E21, E28, E30, E31, E34, E38, E39, E46 and E60/E61. The creator identifies BMW pin 51161828956 and shows the physical result installed. Verify damper eye and panel thickness before fitting.

Fits 3 Series · E21 · 3 Series · E30 · 3 Series · E46 +6

Dual catch-can mounting bracket designed by the creator for the S63TU engine bay in the BMW F13 M6 and F10 M5. The creator links an installation video for the twin-turbo M6 setup, providing physical-use evidence beyond the preserved CAD render. Print in a heat-resistant engineering material such as nylon, keep clear of hot or moving components and hoses, and inspect retention after initial heat cycles. This is an aftermarket accessory with no original BMW component counterpart, so no OEM number is assigned.

Fits 5 Series · F07 / F10 / F11 / F18 · 6 Series · F06 / F12 / F13

Service wrench for the notched BMW fuel-tank screw cap used on E46, E60/E61, E63/E64, E65–E68, E83 and E53 vehicles. The creator tested the same interface on an R53 MINI and identified BMW screw cap 16116762417; BMW catalog cross-reference independently confirms that cap across the listed BMW chassis. The printed wrench is not the screw cap itself, so no OEM number is assigned. Use a stiff engineering polymer, hand tools only, and replace rather than reuse any visibly damaged print.

Fits 3 Series · E46 · 5 Series · E60 / E61 · 6 Series · E63 / E64 +3

Washer-fluid filling funnel for BMW G30 and G31 models and potentially other 5 Series or 7 Series vehicles using the same filler neck. The documented source gallery shows the funnel installed in a G30/G31 filler neck, so only those directly verified generations are linked here. Print in PETG with a 0.4 mm nozzle. Keep the funnel clean, remove it after filling, reinstall the original cap fully, and wipe away spills before driving.

Fits 5 Series · G30 / G31 / G38 / F90

3 pin tool for rewinding rear BMW brakes. I designed the tool to work with a G30, but I think it will work with other BMWs models. The tool is reversable and allows you to either use the triangular pattern for best fit, or the head of the screws. Note: Do not attempt to use without screws installed, it will just shear off the triangular pieces. The design uses #8 x 32 x 1/2" allen head cap screws. For printer settings, beef up the perimeter to 8 and use 50% triangle infill for added strength. Basic PLA did the job. I used the tool successfully to complete a brake job, and redesigned it to improve strength and fit. Simply use a 3/8 ratchet and short extension, then turn clockwise and apply downward pressure. Depending on how tight your calipers are you may only get one use from these, but for a DIY job it works without buying any special tools to compress the caliper. This creator-designed three-pin adapter was successfully used on a G30 rear brake and then strengthened. Install all three specified #8-32 cap screws before use; use a 3/8-inch ratchet and short extension, turn clockwise with controlled downward pressure, inspect the print continuously, and discard it at the first sign of cracking or deformation. Follow the applicable BMW repair procedure and independently support the vehicle; this printed service aid is not an OEM tool.

Fits 5 Series · G30 / G31 / G38 / F90

This fits a BMW F11 and maybe also other BMW cars from around 2015. If the old cable brakes, this is a replacement of the ring at the cap and the cable. The original ring has to be removed from the fuel cap. Be careful not to brake anything else then the turning ring. Use side cutting pliers or a similar tool. The put the new ring onto the fuel cap. If the ring does not fit you can also adjust the width in the attached model and re-export. I used TPU 95 for the print. Nozzle diameter can be 0.25 - 0.4, all work. I printed with supports but this leaves a rough finish. This also leads to the fact, that the ring does not slide as good as the original one. But overall it works. Don't forget to like if you like. Creator reports the TPU replacement fits and works on an approximately 2015 F11, while noting rough support surfaces can make the ring slide less freely. The editable FreeCAD source is retained for measured adjustment. Do not force the ring or damage the fuel cap. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Since I lost two of my backseats isofix covers, I redraw them. Maybe someone else need them as well. I printed them with a 0,2mm nozzle, fuzzy skin at the frontside (strenght 0,04mm / distance 0,1mm), and forced support for the first layers…. The creator measured lost F10/F11 rear-seat covers and provides physical comparisons with the original. This is a cosmetic access cover only; confirm the ISOFIX anchorage remains fully accessible and unmodified. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

This is a usb adapter designed to replace the cigarette lighter in a BMW F07 car. If you have a android head unit it will fit perfectly with the usb port provided. You'll have to remove the central console to have your cable passing through and remove the existing cigarette lighter. A simple rilsan belt will keep it in place. I printed it textured to avoid finger marks. It is very convenient to plug my controller and play games during lunchtime :-) or just plug any thumbstick Designed and used in an F07 with an aftermarket Android head unit. The two source variants share the same envelope but differ internally. Installation requires console removal and replaces the existing 12-volt socket; disconnect power and verify connector retention and insulation. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Replaces metal ashtray in 5 series BMW with a more useful box. Both creator-supplied depth variants are retained. Physical photographs show the insert installed in the F10 console; keep the sliding lid and nearby controls unobstructed. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Just glue the pin to the plate and add some velcro and you are done! The creator tags F10/F11 and supplies physical photographs of the printed two-piece lock. Glue the pin to the plate, add adhesive hook-and-loop material, and confirm the mat cannot interfere with pedal travel. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Hey Guys, i made this Center Console Compartment for my BMW E61. I made it because i had a Phone Holder in my center console which i never used. So i decided to get it out and print myselfe a Compartment. Now i can store more things in my Center Console. I cuted the thing into two parts so you can print it easy. Just glue it together after you printed it. Creator fitted this storage compartment after removing the unused factory phone holder; both complete and split/glue variants are supplied. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

If you want to keep your ashtray tidy, I recommend this model Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Made this for a friend because his original case had a crack. The hole is wider then the stock one because we had to use another aux jack. Feel free to remix it because my version is not perfect. For clipping it in you have to use the original metal clips which fits in the sides of the model. Forgot to make a picture of the 3d Printed model. Designed for a replacement auxiliary jack with a wider opening; reuse the original side metal clips. The creator notes this revision is not cosmetically perfect. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

I edited the clip for E90 made by mrhaze222 so that it would fit in E60 console cover. it should be tight enough to twist it in the hole and strong enough to handle the metal rod,it may get loose a bit if you're planning on taking the cover often so if you want it to hold on longer and be tighter/stronger then you might aswell use the ABS filament but PLA should be enough. It perfectly fits in BMW E60 2003 so it should fit aswell in other models Remixed specifically for the E60 console cover; creator describes the rotational fit and spring-rod retention. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61