car3dparts.

The parts catalog

Find your next part.

Find your fit. Download a free file or choose a maker to print and ship your part.

Reset

65 matching parts

Free files. Made for your car.
Climate-Control Adjustment HandleC3D–01658
MercedesDashboard & controls

Climate-Control Adjustment Handle

Replacement handle for the climate-control panel. The creator states exact 210-series use and provides four CAD views plus a printable part and an editing variant, but no installed photograph or detailed trim/market split. Compare the original handle, shaft and panel before printing, use cabin-heat-resistant material, keep the control mechanism free of debris, and verify full smooth travel and the correct setting indication after installation.

Fits E-Class · W210 / S210

Rear ISOFIX Anchor Trim CoverC3D–01857
MercedesSeats & restraints

Rear ISOFIX Anchor Trim Cover

Working replacement trim plug for the rear-seat ISOFIX anchor opening, derived by the creator from a 3D scan of the factory cover. The creator states that the scan is not perfect; compare the upholstery opening and verify secure seating. This is only a removable trim cap: it must not obstruct, modify or carry load from the ISOFIX anchor, and it should be removed before attaching a child restraint.

Fits E-Class · W213 / S213 / C238 / A238

Modular Console Cupholder and Storage SystemC3D–01844
MercedesConsole & storage

Modular Console Cupholder and Storage System

Multi-part Gridfinity-based replacement for the center-console cupholder and storage unit, explicitly stated by the creator to fit V-Class/Vito, C-Class, E-Class sedan/estate/coupé/cabriolet applications sharing the original insert. It reuses the original double-torsion spring, adds supported cupholder clips, and uses 6×2 mm magnets. Preserve spring orientation, secure every magnet, verify each module locks in place, and keep all contents and moving parts clear of controls. The creator identifies the exact replaced cupholder unit as A2056800691, corroborated by the official Mercedes-Benz genuine-parts listing.

Fits C-Class · W205 / S205 / C205 / A205 · E-Class · W213 / S213 / C238 / A238 · Vito / Viano / V-Class · W447

Folding Sun-Visor ExtensionC3D–01821
MercedesCabin trim, cargo & roof

Folding Sun-Visor Extension

Clip-on folding sun-visor extension designed and physically shown on W212 and S212 driver and passenger visors while retaining access to the illuminated mirrors. The creator supplies separate left/right brackets and a 330 mm panel and requires ABS or ASA because PLA and PETG deform in summer cabin heat. Match the visor and seating position, use the specified high-temperature material, and verify the panel locks securely, folds clear, preserves required road visibility and cannot interfere with airbags.

Fits E-Class · W212 / S212 / C207 / A207

Ashtray MagSafe Charger MountC3D–01820
MercedesDashboard & controls

Ashtray MagSafe Charger Mount

Support-free MagSafe charging mount designed for a W212 E350 across the creator-stated 2009–2016 span and physically shown on top of the centre-console ashtray. It is designed around the linked charging puck, 65 W socket adapter and 70 mm cable; other pucks are untested. Match all electrical and console dimensions, use cabin-heat-resistant material, strain-relieve the cable, avoid trapping heat, and verify the phone and mount remain secure without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Cupholder Accessory Mount BaseC3D–01819
MercedesConsole & storage

Cupholder Accessory Mount Base

Solid and through-hole accessory-mount bases remixed from a W212 cupholder phone-rest geometry and physically shown carrying a suction-mounted display. The author recommends PETG or stronger infill rather than the PLA lightning-infill prototype. Match the cupholder and accessory footprint, use cabin-heat-resistant material and suitable adhesive, and prove the mounted device cannot obscure controls, airbags or the road, overload the cupholder, or detach under braking.

Fits E-Class · W212 / S212 / C207 / A207

Trunk-Well Lid Hinge SocketC3D–01818
MercedesCabin trim, cargo & roof

Trunk-Well Lid Hinge Socket

FDM-optimised replacement for the plastic female half of a trunk-well lid hinge, measured for a 2012 W212. The supplied file is right-hand; the creator instructs mirroring it for the left, printing in PETG with six walls and 25% gyroid infill, and orienting it at 45 degrees for strength. Match the original hinge and lid load, keep the hinge free of wiring and trim, and confirm the service lid opens, closes and remains supported before loading the trunk.

Fits E-Class · W212 / S212 / C207 / A207

Centre-Console Can Holder and TrayC3D–01817
MercedesConsole & storage

Centre-Console Can Holder and Tray

One-piece centre-console insert published specifically for W212 fitment with a 90×78 mm storage compartment and a 66 mm circular recess for European 0.5 L cans. The source shows the printed insert installed but does not state body style, steering side or container-retention testing. Measure the console and container, use cabin-heat-resistant material, and confirm the insert seats fully, keeps a closed cool can stable and cannot obstruct the selector or controls.

Fits E-Class · W212 / S212 / C207 / A207

PCMCIA-Slot Phone HolderC3D–01816
MercedesDashboard & controls

PCMCIA-Slot Phone Holder

Phone holder designed for the PCMCIA slot in a 2010 C207 E500 coupe and around the creator’s phone with a Spigen card case, then printed in PETG. No other head-unit revision, phone or body style is established. Match the slot, card mechanism, phone and case dimensions; insert without forcing the electronics, and verify the mount cannot obscure controls, airbags or the road or eject the phone under braking.

Fits E-Class · W212 / S212 / C207 / A207

Rear Sunshade Vent and Handle RepairC3D–01815
MercedesCabin trim, cargo & roof

Rear Sunshade Vent and Handle Repair

Four-part repair for the breakable sunshade vent/handle assembly in a W212, described by the creator as installed and tested in their car. The top and bottom handle pieces are joined with M2 screws; the creator later found the lower vent piece alone easier to install and recommends a higher-temperature material despite successful PLA use. Compare the broken assembly, use cabin-heat-resistant material, avoid over-tightening screws, and verify free shade and vent movement.

Fits E-Class · W212 / S212 / C207 / A207

Multi-Function Cupholder InsertC3D–01814
MercedesConsole & storage

Multi-Function Cupholder Insert

Author-designed centre-console insert for W212 cars, physically shown in use with cups and a phone. The source supplies variants for 14 mm, 20 mm and 84 mm-wide phone cases plus can-stabilising rings, coin and card storage, specifies 24×3.5 mm felt pads for retention, and warns not to use PLA in summer cabin heat. Select only the matching variant, use heat-resistant material, fit the felt pads, and verify containers, cards and phone remain secure without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Cupholder Phone RestC3D–01813
MercedesConsole & storage

Cupholder Phone Rest

Cupholder-mounted phone rest designed for pre-facelift 2010–2011 W212 E350 sedans. The author shows the physical print with the original cupholder and states that its open centre permits a charging cable while the factory cover can still close. Print in ABS or another proven cabin-heat-resistant material, match the cupholder and phone dimensions, route the cable clear of controls, and verify the rest cannot release the phone or interfere with the selector under braking.

Fits E-Class · W212 / S212 / C207 / A207

Factory Cupholder Beverage InsertsC3D–01812
MercedesConsole & storage

Factory Cupholder Beverage Inserts

Bottle and small-can inserts for the factory option-code 309 cupholder used in stated W212 and S212 cars with 7G-TRONIC-PLUS or 9G-TRONIC transmissions. The selected author files fit a 0.5 L beverage bottle and a 250 ml slim can; the unrelated vape-holder variant is deliberately not distributed. Match factory cupholder A 212 680 01 10 and the container dimensions, use cabin-heat-resistant material, and verify each insert and closed beverage remain retained without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Rear Sunshade HandleC3D–01811
MercedesCabin trim, cargo & roof

Rear Sunshade Handle

Replacement handle designed for a broken rear-seat sun-protection shade and explicitly tagged for the S212 estate. The creator states that the printed handle must be drilled to 2.5 mm for final fit; no sedan, coupe or cabriolet application is established. Compare the original handle and pivot, use tough UV- and cabin-heat-resistant material, drill carefully, and confirm smooth shade movement without stressing the shade fabric or mechanism.

Fits E-Class · W212 / S212 / C207 / A207

Dashboard iPhone HolderC3D–01810
MercedesDashboard & controls

Dashboard iPhone Holder

Three-file phone holder designed and physically shown in a W212 dashboard and explicitly stated for W212 sedan and C207 coupe fitment. The main geometry fits an iPhone XR; an adapter fits an iPhone 6S, and the creator recommends a 2 mm metal reinforcing rod plus a separately printed rubber pad for hot-cabin durability. Match the phone and dashboard interface, use heat-resistant material, assemble every piece securely, and verify the holder cannot obscure controls, airbags or the road or release the phone under braking.

Fits E-Class · W212 / S212 / C207 / A207

Wheel Socket and Lock-Key TrayC3D–01809
MercedesInterior doors & windows

Wheel Socket and Lock-Key Tray

Trunk-floor tray designed specifically for the left-side storage recess of the W212 sedan and for a 17 mm wheel-nut impact socket plus a stated 28018SL wheel-lock key. The creator supplies the exact intended tools but does not state body-style alternatives or road testing. Compare the recess and tool dimensions, use tough cabin-heat-resistant material, and confirm both tools remain fully captured and cannot rattle loose or become projectiles.

Fits E-Class · W212 / S212 / C207 / A207

Overhead Trunk HookC3D–01808
MercedesCabin trim, cargo & roof

Overhead Trunk Hook

Two-piece hook designed for the existing oval opening in the upper trunk sheet metal of the W212 sedan. The creator specifies two M4×10 mm countersunk screws and a sliding dead-bolt piece; the source identifies the installation position but does not show the hook installed or state a load rating. Use tough heat-resistant material, inspect the opening and sheet-metal edges, tighten both screws, and use only for light soft items after proving retention; never treat it as a cargo-restraint or safety anchor.

Fits E-Class · W212 / S212 / C207 / A207

COMAND Controller Joystick ShaftC3D–01796
MercedesDashboard & controls

COMAND Controller Joystick Shaft

Internal joystick shaft for the COMAND controller, measured from a broken original and redesigned without its nut. The creator explicitly identifies C-Class W204 and E-Class W212 applications and specifies 0.1 mm layers and 100% infill; no other W212-generation body styles are stated. Compare the removed shaft and controller revision, use tough cabin-heat-resistant material, transfer and assemble the mechanism without damaging electronics and verify full rotary, tilt and press operation before driving.

Fits C-Class · W204 / S204 / C204 · E-Class · W212 / S212 / C207 / A207

Console Switch-Panel BlankC3D–01752
MercedesDashboard & controls

Console Switch-Panel Blank

Blank insert for the MP3-button position in the center-console switch panel. The author identifies the exact chassis and supplies the printable geometry, but does not establish applicability to every switch-panel or equipment variant; compare the opening before printing.

Fits E-Class · W211 / S211

CD-Changer-Bay Storage CompartmentC3D–01747
MercedesConsole & storage

CD-Changer-Bay Storage Compartment

Four-piece concealed storage compartment installed in place of the factory CD changer and opened with the button below the radio. The source states automatic closing after 30 seconds; wiring and actuator details remain the installer’s responsibility.

Fits E-Class · W211 / S211

Roof-Trim Opening CapC3D–01746
MercedesBody panels & exterior trim

Roof-Trim Opening Cap

Replacement cap for the roof-trim opening. The source includes the printed cap and installed physical views; confirm the opening dimensions and trim variant before installation.

Fits E-Class · W211 / S211

Rear-Bumper Support BracketC3D–01745
MercedesBumpers, grilles & guards

Rear-Bumper Support Bracket

Replacement rear-bumper support bracket corresponding to the exact child number identified by the creator. Print upright with high infill in ABS or polycarbonate-class material, use support only at the latch, and remove the modeled sacrificial support from the screw hole after printing.

Fits E-Class · W211 / S211

Nine-Inch Stereo Installation FrameC3D–01740
MercedesConsole & storage

Nine-Inch Stereo Installation Frame

Three-piece installation frame for a nine-inch Android head unit. The author describes it as functional but imperfect and requiring finishing; join all three parts as shown by the source and check secure retention before driving.

Fits E-Class · W211 / S211