Find your next part.

Replacement collar stop for the hand-throttle rod, upgraded with two M3 set-screw holes that must be tapped after printing.

Fits 911 · Original (901/911)

Right-rear guide that receives the electric sunroof lifting arm and raises the roof. The creator reports that right and left guides restored operation on a 1984 car and says the opposite side can be produced by mirroring this model.

Fits 944 · 944

Two-piece center-console cupholder replacement designed 1 mm smaller than the stock console to allow vinyl wrapping. The creator plastic-welded the pieces, wrapped the assembly in vinyl, and supplied printable inserts plus a logo stencil.

Fits 944 · 944

Removable dual cup-holder assembly whose bracket wedges between the center dashboard and upper center console. The cup holders can be stored in the armrest when not in use.

Fits Boxster · 986

Center-console tray remix for an iPhone 13 Pro and Anker 15W PowerWave Alloy charging pad, with added phone-positioning blocks and a lower cutout to clear the flip-up cover. It installs after removing the factory rubber liner.

Fits 911 · 991 · Boxster · 981 · Cayman · 981

Passenger/right headlight-washer cover with tabs and a companion jig used to heat-form the cover to the compound curve against the headlight housing.

Fits 911 · 996

Five snap-in inserts for the dashboard vent openings that hold recovered vinyl around the holes without glue. The creator says they snap into place and prints them in ABS.

Fits 944 · 944

Support clip for the 997 front-bumper mesh and slats. The supplied version 2 STL is smaller and more concealed than the photographed version 1; use 3 mm cable ties and two clips per side.

Fits 911 · 997

Three printable shift-linkage repair inserts designed for a 1997 five-speed car. The creator specifies PETG or ABS, no supports, 40% infill and 2 mm walls, and reports positive initial road-test results.

Fits Boxster · 986

Two-piece iPhone 12 Pro Max support that replaces the CD-storage function while retaining the original surround; the two printed modules assemble with three M3 x 10 screws.

Fits Boxster · 986

Replacement retaining pin and small gear for the dashboard cup-holder mechanism. The creator thickened the pin for easier printing, increased the gear height for better mesh, and used an 18-gauge brad nail as the pivot. The parts were printed in PETG after PLA softened in a hot car.

Fits Boxster · 987 · Cayman · 987

Replacement centre dashboard air vent recreated after the original in a 1976 Porsche 911 cracked. The creator reports that the ABS print fit perfectly and provides plain and brim-supported STL variants.

Fits 911 · G Model

Replacement flap for the fresh-air blower housing. The creator used a 4 mm foam-rubber seal and PETG for the heat encountered during cabin heating.

Fits 911 · G Model

Repair bracket for the broken air-filter-box arm that retains the metal band connecting the housing to the turbocharger discharge/intercooler pipe. The printed bracket attaches to the top of the box by hot stapling, plastic welding, or adhesive and uses a small pin for the steel band.

Fits 944 · 944

Printable camshaft holding-down tool for early five-chain engines in the Boxster 986 and 911 996. The tool holds the camshafts during cylinder-head-cover removal and reassembly.

Fits 911 · 996 · Boxster · 986

Full-size 15.25-inch template for cutting replacement side-section stone-guard film, modeled for the 997 generation.

Fits 911 · 997

Replacement cap for the Cabriolet hardtop-latch opening. The creator says it hides the latch mechanism, may need approximately 1% scale adjustment depending on printer accuracy, and should be printed flat-side down.

Fits 911 · 996

Shim-style retaining clip that wraps around a rear quarter-window molding tab, locks through the tab hole, and holds the molding in the rubber surround. Seven clips are used per side.

Fits Cayenne · E2 (958)

Replacement blower-intake grille offered as an integrated printable-mesh cover or an open frame for a separate filter or aluminum mesh.

Fits 944 · 944

Replacement for disintegrating heater-panel lever knobs. The single arrowless design presses onto and can be removed from the heater-control levers; it intentionally omits the faint side arrows found on two originals.

Fits 924 · 924

Adapters for 4-inch door and rear midrange drivers plus a two-piece Dynaudio MD-102 tweeter mount. The source covers Dayton Audio RS100/RS100P and Dynaudio E430 midranges; the tweeter mount requires Burmester grilles or modified Bose/SPP grilles and its two pieces are bonded before installation.

Fits 911 · 991

Printable replacement for the break-prone front-seat backrest release control button, modeled from the shared latch style used across the listed seat applications.

Fits 911 · G Model · 911 · 964 · 911 · 993 +4

Headliner-mounted radar-detector bracket secured beneath the passenger visor support, with tie-wrap or hook-and-loop attachment points for the detector.

Fits Cayman · 987

Adapter for mounting an Advance Auto Parts #172650 Camaro washer pump to the factory VDO washer-pump bracket. It mounts with 3x8 mm or 3x12 mm machine screws; the pump is retained with heavy-duty tape and two ties.

Fits 944 · 944