car3dparts.

The parts catalog

Find your next part.

Find your fit. Download a free file or choose a maker to print and ship your part.

Reset

122 matching parts

Free files. Made for your car.
Gladen Alpha 130 G2 Tweeter Mount PairC3D–01392
BMWCabin trim, cargo & roof

Gladen Alpha 130 G2 Tweeter Mount Pair

I designed these brackets because the original BMW E39 tweeter mounts are too small to fit the Gladen Alpha 130 G2 tweeters. Installing aftermarket tweeters in the factory location can be challenging, as the available space inside the original E39 mounting brackets is very limited. These adapters allow the Gladen tweeters to be mounted securely while retaining the factory installation position. Compatible Speaker Set Gladen Alpha 130 G2 Original BMW Parts Left side: 65138362527 Right side: 65138362528 OEM reference: Printing Notes Designed for BMW E39 factory tweeter locations. Tested with Gladen Alpha 130 G2 tweeters. PETG or ASA is recommended for improved heat resistance inside the vehicle. Print with at least 3 perimeters and 30–40% infill for good durability. I hope this model helps anyone upgrading the factory audio system in their BMW E39. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Facelift Fog-Lamp Mount Repair PairC3D–01391
BMWExterior lighting, cameras & sensors

Facelift Fog-Lamp Mount Repair Pair

Replaces the integrated plastic tab that commonly shears off, allowing the fog light to be secured without replacing the entire bumper. The bracket replicates the factory slot geometry. Once bonded, the fog light housing slides into the bracket and locks into place using the original mounting hardware/method. Material: Would recommend ASA or ABS. Compatibility: 2001–2004 (Facelift / LCI) BMW E39 5-Series models. Will not fit Pre-Facelift or M-Sport/M5 Bumpers. I also sell the printed parts: Installation Instructions: 1. Access: Gain access to the fog light assembly either by removing the front splash guard in the wheel well or by removing the front bumper entirely. 2. Alignment: Leave the fog light attached to the bumper by its remaining intact mounting point. 3. Test Fit: Position the repair bracket and verify that it makes flush contact with the bumper surface. Ensure the circular tab on the fog light housing slots correctly into the bracket. 4. Preparation: If remnants of the broken original bracket interfere with the fitment, trim them down until the repair bracket sits flush. 5. Bonding: Thoroughly clean the contact areas on both the bracket and the bumper. Apply a strong epox Creator limits fitment to the facelift/LCI bumper. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Speaker-Enclosure Sealing PlateC3D–01388
BMWCabin trim, cargo & roof

Speaker-Enclosure Sealing Plate

This speaker plate is designed for the BMW E39 speaker enclosure and replaces the original crossover filter. Allows the box be airtight when using with aftermarket speakers for better sound quality. Cable hole is designed for 2x1.5mm2 cable Hole size is: 7mm x 4mm Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Sun-Visor Retaining ClipC3D–01381
BMWCabin trim, cargo & roof

Sun-Visor Retaining Clip

This is the design I made to replace my broken sun visor clip in my 2000 BMW E39 528i Touring. It is a little difficult to snap in but has a nice fit once it's clipped in all the way. Some filing or sanding might fix the stiff fit. Creator reports fitment in a 2000 E39 528i Touring. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Front-Speaker Sealing RingC3D–01379
BMWCabin trim, cargo & roof

Front-Speaker Sealing Ring

...trying to fit aftermarket speakers in my e39 bmw i found out that they leave a gap to the standard boxes in the front doors. so i quickly designed these simple rings to close the gap, Use TPU to print them to ensure a tight fit. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Armrest Telephone-Delete Inlay SetC3D–01377
BMWSeats & restraints

Armrest Telephone-Delete Inlay Set

You probably do not use your E39 bluetooth phone anymore. Don't waste this space in your car and print my inlay to make this area useful for you. There are different versions available, I hope you will be able to chose the most fit for you;) I personally use the one with the grooves for phones. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Door-Mirror Cover Latch RepairC3D–01372
BMWMirrors

Door-Mirror Cover Latch Repair

Ther is the Mirror cover bmw e39 latch instead broken one! For each cover you need 2 direct and 2 mirror printed parts. Just put on things to the broken parts, try to put cover on mirror (i need to cut height for 2 of them) and fix it with glue. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

OEM Cup-Holder ReinforcementC3D–01368
BMWConsole & storage

OEM Cup-Holder Reinforcement

Pair of reinforcement brackets for fitting a universal T2/T3 cup holder in a BMW E39. The creator reports that it supports McDonald’s drink sizes without smaller cups tipping and accepts PET bottles up to 0.5 litres. Print two brackets in ABS or PETG; PLA can deform in summer cabin heat. After printing, tap M4 threads in the holes, shorten the screws so they sit flush without protruding, and attach the brackets to the cup holder. These replace the unstable sheet-metal clips supplied with the universal holder. Verify dimensions, fastening, and unobstructed operation before regular use.

Fits 5 Series · E39

RHD Console Drink CompartmentC3D–01367
BMWConsole & storage

RHD Console Drink Compartment

This is for all the RHD E39 owners because I couldn't find any online except LHD so I designed a new one :D When printing flip the whole thing on its bottom so it prints properly. :D Btw the pictures got squashed by the site so to see a better image view the original image by clicking the fullscreen button at the top right and then click view original image. Creator identifies right-hand-drive fitment. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Upper Side-Sunblind ClipC3D–01366
BMWCabin trim, cargo & roof

Upper Side-Sunblind Clip

Clip zum anschrauben der oberen Seitenrollohalter im Türrahmen. Bei BMW leider nicht im ETK zu finden. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39 · 7 Series · E38

Touring License-Plate Bracket FastenerC3D–01365
BMWWheels, plates, towing & roof equipment

Touring License-Plate Bracket Fastener

My E39 Touring was missing one of the clips to hold in the plate bracket (plinth). The previous owner had used silicone to hold the panel on. Unable to live with this I contacted the dealership - who were unable to find the part in their system. Doubting their competence I checked realoem myself and actually couldn't find a part number. So I turned to Fusion360 and whipped these up. I've never designed anything before so please bear with me. I have made two revisions of this thing. **(bmw_plate_plinthe_v3)** The first is a copy of the original - fits snug and locks nicely. - It may be a good idea to use a bit of RTV or Butyl Rubber around the hole to keep water out! **(Nut.stl /Thread.stl)** The second is a threaded option. Allowing you to fit an M8x1.25 nut on the back. This option was created for people who may have corrosion around the hole thus making it too big for the snap in option. Printed these on my CR-10S w/ 99% concentric infill 5 walls and 0.12 layer height @ 35mm/s Hopefully they can be of use to someone else too. Cheers. Apparently fits these models too! BMW E30 318i M10 1.8L BMW E30 318i M42 1.8L BMW E30 318is M42 1.8L BMW E30 325i M20 2.5L BMW E30 325is M20 2.5L BM Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Touring Tailgate Side-Cover ClipC3D–01359
BMWCabin trim, cargo & roof

Touring Tailgate Side-Cover Clip

My BMW E39 wagon (touring) was missing the plastic clips at both sides of the tailgate. These clips hold the plastic side covers in place. Since the original spare parts (BMW part number: left: 51498217213, right:51498217214) are way too expensive, I have decided to print my own ones. The uploaded files contain the right side clips, but you can mirror them in Cura so that you also have the left side ones (see pictures). BMW catalog identifies the black left/right clips from 1996-09 for E39 Touring, including cataloged European/USA and LHD/RHD applications; mirror the supplied right-side model for the left. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Power-Mirror Selection SwitchC3D–01358
BMWMirrors

Power-Mirror Selection Switch

My BMW E39 5 Series was missing the selection switch for the power mirror. (I don't know how the previous owner could rip that thing off...) Here you can find a custom-made replacement switch. Just push it into its place. If you have any ideas for improvement, please feel free to contact me. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Trunk Toolbox Retaining StrapC3D–01357
BMWCabin trim, cargo & roof

Trunk Toolbox Retaining Strap

The toolbox holding strap on my car broke in the middle due to material stress over the years. Designed a new strap with with a hinge, to prevent this from happening in the future. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Sunroof-Control Headliner CoverC3D–01351
BMWCabin trim, cargo & roof

Sunroof-Control Headliner Cover

Replacement 158.2×191.0×12.8 mm headliner cover for the E34 sunroof-control area, supplied as STL and STEP and shown against the installed roof console. The creator recommends ABS or PETG at full infill. Verify sunroof switch, interior-light and headliner opening configuration because option and trim variations are not interchangeable.

Fits 5 Series · E34

Rear-Reflector Retaining ClipC3D–01350
BMWExterior lighting, cameras & sensors

Rear-Reflector Retaining Clip

Replacement clip for retaining the rear lamp reflector on a BMW E34 when the small fastener is damaged but the reflector assembly remains serviceable. The source shows the original lamp hardware and recommends PETG with tree supports. Compare the clip pocket and reflector condition before installation; no parent lamp number is assigned.

Fits 5 Series · E34

Touring Telephone-Antenna CapC3D–01349
BMWBody panels & exterior trim

Touring Telephone-Antenna Cap

Thread-forming replacement cap for the roof telephone antenna on an E34 Touring. The creator printed it in PETG, formed the thread with gentle heat and painted the physical part satin black. This is body- and antenna-option-specific; confirm the Touring roof fitting and thread diameter before heating or installation.

Fits 5 Series · E34

Automatic Climate-Control Retaining ClipC3D–01348
BMWDashboard & controls

Automatic Climate-Control Retaining Clip

Replacement retaining clip for the automatic climate-control unit in an E34 M5. The creator physically installed the PETG print, sanded the nibs slightly and reports that it holds the unit. This differs from the separate HVAC actuator-arm clip; compare the installed clip and remove only minimal material for a secure snap fit.

Fits 5 Series · E34

Early LOW-Cluster Odometer Gear SetC3D–01345
BMWDashboard & controls

Early LOW-Cluster Odometer Gear Set

Three replacement gears for the mechanical odometer in the early E34 LOW instrument cluster. The creator limits the set to start-of-production through September 1990 clusters used in 518i, 520i, 524td, 525td and 525tds variants. Compare the cluster face and tooth counts before disassembly; later or HIGH clusters are not represented.

Fits 5 Series · E34

Automatic-Shifter Slide CoverC3D–01344
BMWConsole & storage

Automatic-Shifter Slide Cover

Flexible replacement strip for the E34 automatic selector gate, with a 16 mm opening for the shifter stalk. The creator specifies TPU at roughly 50% infill. Verify selector travel through every position and ensure the strip cannot bind, bunch up or interfere with the shift-lock mechanism.

Fits 5 Series · E34

Lower Side-Panel ClipC3D–01343
BMWCabin trim, cargo & roof

Lower Side-Panel Clip

Replacement push clip for attaching the lower interior side panel in a BMW E34. The source is chassis-specific and supplies the mating clip geometry. Compare stem diameter and panel thickness with the surviving fastener and use a flexible, heat-tolerant material so removal does not damage the trim.

Fits 5 Series · E34