Find your next part.

Replacement clip copied from the surviving original on an E34 climate-control actuator. It snaps into the actuator while the flap-control arm clips into its center. Print in a heat-tolerant engineering material and compare both snap features with an intact original before cycling the HVAC system.

Fits 5 Series · E34

Two-piece cup holder physically fitted in the center-console tray of a 1990 E34 525i. Its foot resists tipping, the lower bore is 64 mm and the upper opening is 82 mm with a mug-handle slot. Adjust the press fit in the actual console before bonding the halves and check shifter and handbrake clearance.

Fits 5 Series · E34

Hand tool for aiming classic BMW headlamps that use a 3/8-inch square plastic adjuster, including E28, E24 and E23 lamps. The source provides 60, 100 and 150 mm shaft options and recommends a stiff filament. BMW numbers 63121362049 and 63121369857 identify the nut and screw being adjusted, not the printed tool, so no OEM number is assigned.

Fits 5 Series · E28 · 6 Series · E24 · 7 Series · E23

Drop-in cup holder for the BMW E28 center console, shown physically installed beside the shifter. The source is dedicated to this chassis and released to the public domain. Confirm console shape, shifter travel and access to adjacent controls before use; finish or pad contact surfaces as needed to prevent trim abrasion.

Fits 5 Series · E28

Protective cap for the top of the front strut mount on BMW E28 models. The creator printed it in PETG and road-tested the design for 5,000 miles before release. BMW catalogs identify the equivalent 28.5 mm covering cap as 31331124335; do not confuse it with the separate dust-protection collar 31331110196. Verify top-nut and mount dimensions before use.

Fits 5 Series · E28

Reinforcement bracket that replaces the flat nut at an E28 glovebox mounting point. Three prints and one M4 nut per bracket position are required to reinforce all mounting points. The creator used ABS+ and shows the parts fitted to the glovebox panel. Check screw length and ensure the bracket does not distort the glovebox shell.

Fits 5 Series · E28

Replacement throttle-body linkage/cable nipple for the M10-powered BMW E28 518i; two identical pieces are required in the catalog assembly. The design is based on an original part and includes print-orientation guidance. BMW number 13541286378 is cataloged specifically for E28 518i M10 applications and selected M10-powered E30 models, not every E28 engine.

Fits 3 Series · E30 · 5 Series · E28

Two alternative lower hook-holder geometries for the BMW accessory rear roller sunshade: an original-dimension version and a tighter-fit version tested in an early 1985 car. BMW references include discontinued white accessory hook 82129413177 and anthracite holder 51461905393, which supersedes 51461887130. E28/E30 body, production date, color and accessory installation vary; compare the no-screw-hole mounting style before use.

Fits 3 Series · E30 · 5 Series · E28

Replacement manual shifter-boot retaining frame for BMW E28 and E24 interiors. The creator measured an E28, fitted the design in the car and recommends PETG because PLA prototypes softened in cabin heat. The test car has a short shifter; correct worn or misadjusted linkage rather than relying on this frame to solve reverse-gear interference.

Fits 5 Series · E28 · 6 Series · E24

Replacement rotating knob/head for the manual sunroof crank of a BMW E28. The creator printed the part in PLA; PETG or ABS is preferable for a hot cabin. BMW catalogs supply the knob only with the complete crank handle, so no parent-assembly number is assigned. Confirm crank-pin diameter, trim color and production-date variation before fitting.

Fits 5 Series · E28

Replacement plastic retaining clip for the classic 14-inch steel wheel cover used on early BMW E28 cars. BMW catalogs identify the clip as 36131125740, used with wheel cover 36131125718 through September 1984; it is discontinued with no cataloged supersession. Verify the wheel-cover style and production date before use, and inspect every clip for secure retention.

Fits 5 Series · E28

Adjustable clutch-pedal stop body for manual-transmission BMW E28 and other listed classic BMW chassis. Assembly requires an M10 screw, two M10 nuts, a 40 mm washer and a genuine-style rubber cap. Adjust only far enough to remove excess pedal travel while preserving complete clutch disengagement, then lock the nuts securely and re-check operation before driving.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +4

Front and rear spacer geometry with locating rod for installing a Musway ME462 coaxial speaker in a BMW E28 sedan. The creator reports that the adapter set fits perfectly. This is specific to the stated speaker footprint; compare the mounting pattern, depth and trim clearance before printing for another driver.

Fits 5 Series · E28

Spacer and washer for fitting an upgraded 4×6-inch front speaker in a BMW E28 while retaining the original speaker cover. The creator confirms that the hood-release lever still clears the speaker and specifies longer #8×1.25-inch oval-head screws with #6-32 speed nuts. Check speaker depth and fastener clearance before final assembly.

Fits 5 Series · E28

Three-piece replacement bracket set for the BMW E28 front lower valance: left, center and right. The creator states that the parts fit in the stock locations and replaces factory brackets that commonly break or go missing. Use a UV- and heat-resistant engineering material, verify the valance variant and compare the mounting-hole geometry before fitting.

Fits 5 Series · E28

Clip-on shopping-bag hook demonstrated on the factory rear parcel-shelf cover of BMW F31 and G31 Touring models. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80 · 5 Series · G30 / G31 / G38 / F90

These clips can be glued in your oval mirror housing of a BMW E39 M5 or E46 M3 to repair the broken ones. Use "crazyglue" and line the clips up with the missing tabs in the housing. See photos for reference. Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46 · 5 Series · E39

Replacement front engine wiring holder for E30 M20 and creator-listed E28/E34 applications, physically compared with the original. BMWFans confirms holder 11141716134. Use ASA, ABS or another engine-bay-rated material and inspect for heat distortion.

Fits 3 Series · E30 · 5 Series · E28 · 5 Series · E34

Replacement side covers for BMW Reverse RDS, non-RDS, Bavaria and Business radios used in E30, E32, E34 and E36. The source shows physical fit and finish; BMWFans confirms covering cap 65126907823.

Fits 3 Series · E30 · 3 Series · E36 · 5 Series · E34 +1

Printed cap wrench for the 76 mm, 14-flute oil-filter housing associated with BMW 11421715960. The creator physically demonstrates the tool and lists E30, E36, E46, E34 and Z3 applications; confirm cap size before applying torque.

Fits 3 Series · E30 · 3 Series · E36 · 3 Series · E46 +2

Dimensioned replacement switch knob for the Hella-style interior dome light used in BMW E12, E21 and E30. Physical prints are shown on the lamp. The creator-listed numbers identify complete lamp variants rather than this knob, so no parent-assembly number is submitted.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E12

Replacement door-lock knob for BMW E21, E28 and E30, physically shown beside the original hardware and designed to work with the original or matching printable sleeve. The creator's mixed knob/sleeve catalog references are intentionally omitted. Verify pin diameter and retention.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E28

Replacement door-lock knob sleeve for BMW E21, E28 and E30, enlarged slightly for improved fit and physically demonstrated with the matching knob. The creator's two catalog references cover both sleeve and knob; neither is submitted here because public catalogs did not unambiguously map one number to this modified sleeve.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E28

Replacement trim ring or rosette for the manual sunroof handle on BMW E21, E28 and E30. The creator reports original-location fit and identifies BMW trim ring 54121867887, independently listed for E21 by RealOEM/BMWFans. Verify sunroof-handle version before fitting.

Fits 3 Series · E21 · 3 Series · E30 · 5 Series · E28