Find your next part.

One-piece centre-console insert published specifically for W212 fitment with a 90×78 mm storage compartment and a 66 mm circular recess for European 0.5 L cans. The source shows the printed insert installed but does not state body style, steering side or container-retention testing. Measure the console and container, use cabin-heat-resistant material, and confirm the insert seats fully, keeps a closed cool can stable and cannot obstruct the selector or controls.

Fits E-Class · W212 / S212 / C207 / A207

Phone holder designed for the PCMCIA slot in a 2010 C207 E500 coupe and around the creator’s phone with a Spigen card case, then printed in PETG. No other head-unit revision, phone or body style is established. Match the slot, card mechanism, phone and case dimensions; insert without forcing the electronics, and verify the mount cannot obscure controls, airbags or the road or eject the phone under braking.

Fits E-Class · W212 / S212 / C207 / A207

Four-part repair for the breakable sunshade vent/handle assembly in a W212, described by the creator as installed and tested in their car. The top and bottom handle pieces are joined with M2 screws; the creator later found the lower vent piece alone easier to install and recommends a higher-temperature material despite successful PLA use. Compare the broken assembly, use cabin-heat-resistant material, avoid over-tightening screws, and verify free shade and vent movement.

Fits E-Class · W212 / S212 / C207 / A207

Author-designed centre-console insert for W212 cars, physically shown in use with cups and a phone. The source supplies variants for 14 mm, 20 mm and 84 mm-wide phone cases plus can-stabilising rings, coin and card storage, specifies 24×3.5 mm felt pads for retention, and warns not to use PLA in summer cabin heat. Select only the matching variant, use heat-resistant material, fit the felt pads, and verify containers, cards and phone remain secure without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Cupholder-mounted phone rest designed for pre-facelift 2010–2011 W212 E350 sedans. The author shows the physical print with the original cupholder and states that its open centre permits a charging cable while the factory cover can still close. Print in ABS or another proven cabin-heat-resistant material, match the cupholder and phone dimensions, route the cable clear of controls, and verify the rest cannot release the phone or interfere with the selector under braking.

Fits E-Class · W212 / S212 / C207 / A207

Bottle and small-can inserts for the factory option-code 309 cupholder used in stated W212 and S212 cars with 7G-TRONIC-PLUS or 9G-TRONIC transmissions. The selected author files fit a 0.5 L beverage bottle and a 250 ml slim can; the unrelated vape-holder variant is deliberately not distributed. Match factory cupholder A 212 680 01 10 and the container dimensions, use cabin-heat-resistant material, and verify each insert and closed beverage remain retained without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Replacement handle designed for a broken rear-seat sun-protection shade and explicitly tagged for the S212 estate. The creator states that the printed handle must be drilled to 2.5 mm for final fit; no sedan, coupe or cabriolet application is established. Compare the original handle and pivot, use tough UV- and cabin-heat-resistant material, drill carefully, and confirm smooth shade movement without stressing the shade fabric or mechanism.

Fits E-Class · W212 / S212 / C207 / A207

Three-file phone holder designed and physically shown in a W212 dashboard and explicitly stated for W212 sedan and C207 coupe fitment. The main geometry fits an iPhone XR; an adapter fits an iPhone 6S, and the creator recommends a 2 mm metal reinforcing rod plus a separately printed rubber pad for hot-cabin durability. Match the phone and dashboard interface, use heat-resistant material, assemble every piece securely, and verify the holder cannot obscure controls, airbags or the road or release the phone under braking.

Fits E-Class · W212 / S212 / C207 / A207

Trunk-floor tray designed specifically for the left-side storage recess of the W212 sedan and for a 17 mm wheel-nut impact socket plus a stated 28018SL wheel-lock key. The creator supplies the exact intended tools but does not state body-style alternatives or road testing. Compare the recess and tool dimensions, use tough cabin-heat-resistant material, and confirm both tools remain fully captured and cannot rattle loose or become projectiles.

Fits E-Class · W212 / S212 / C207 / A207

Two-piece hook designed for the existing oval opening in the upper trunk sheet metal of the W212 sedan. The creator specifies two M4×10 mm countersunk screws and a sliding dead-bolt piece; the source identifies the installation position but does not show the hook installed or state a load rating. Use tough heat-resistant material, inspect the opening and sheet-metal edges, tighten both screws, and use only for light soft items after proving retention; never treat it as a cargo-restraint or safety anchor.

Fits E-Class · W212 / S212 / C207 / A207

One-piece holder designed specifically for the front-seat console of a 2014 C207 coupe. The creator states that other vehicles may fit but supplies no evidence for them. Match the console opening and container dimensions before printing, use cabin-heat-resistant material, and confirm that the holder cannot obstruct the selector or controls, spill into electronics, or release a container under braking.

Fits E-Class · W212 / S212 / C207 / A207

Snap-in plastic-panel mounting pin published for Mercedes GLK and C-Class vehicles. The creator does not identify its panel position, body side, market, model year, original part number, material or test history. Compare the removed fastener, panel thickness, slot dimensions and installed clearance before printing; use a tough automotive-interior or exterior-grade material suitable for the actual location, and confirm the panel remains securely retained without damaging adjacent trim. Do not substitute this print for a structural, restraint or load-bearing fastener.

Fits GLK / GLC · X204

Flexible replacement tether published specifically for this generation. The creator requires TPU and instructs removal of the lid pin and remaining old tether before fitting the new piece snugly around the fuel cap without affecting its seal. Compare the pin, cap eye, tether length and filler-lid clearance, use fuel-vapour-, UV- and weather-resistant TPU and confirm the tether cannot enter the filler neck or prevent the cap from sealing completely.

Fits C-Class · W204 / S204 / C204

Cupholder insert designed and printed for charging a Huawei P30 Pro from an Anker PowerPort wireless charger while leaving the rear storage compartment available. The source shows the physical insert and phone in the vehicle and includes one selected STL plus the preserved editable author file. Match the cupholder, phone and charger dimensions, use cabin-heat-resistant material, protect and strain-relieve the power lead and confirm the phone and insert cannot obstruct the selector or controls or detach under braking.

Fits C-Class · W204 / S204 / C204

Compartmented insert designed for the door pocket across the stated 2007–2015 production span, with spaces for cards, a flashlight, tissues or a small shaver and pens. The source supplies one STL and one source CAD image but does not identify door side, body style or steering market. Measure the pocket and stored items, use tough cabin-heat-resistant material and confirm the insert seats fully without scratching trim, interfering with door operation or allowing hard objects to escape under braking.

Fits C-Class · W204 / S204 / C204

Combined navigation-display holder and Galaxy S20 Ultra case published for this generation and shown installed in the source vehicle. The creator links both recoverable remix sources and instructs printing the supplied geometry at 1% scale. Confirm that scaling produces the intended phone and dashboard-interface dimensions before printing, use cabin-heat-resistant material and verify that the mount cannot obstruct controls, airbags or the road or release the phone under braking.

Fits C-Class · W204 / S204 / C204

Replacement retaining nut published specifically for this generation and supplied with a source CAD image. The creator does not state the underbody panel position, thread dimensions, engine, drivetrain, body style, material or test history. Compare the original nut, stud thread, panel thickness and installed clearance, use heat-, water-, salt- and impact-resistant material and confirm the underbody cover is fully retained after a road test; do not use this print for structural, suspension or lifting points.

Fits C-Class · W204 / S204 / C204

Phone mount published specifically for this generation and a Samsung Galaxy S5. The author supplies one printable model and a source CAD image but does not state the head-unit revision, mounting procedure, steering side or road testing. Match the device and dashboard interface before printing, use cabin-heat-resistant material and confirm the mount cannot damage trim, obstruct the display, controls, airbags or road view, or release the phone under braking.

Fits C-Class · W204 / S204 / C204

Internal joystick shaft for the COMAND controller, measured from a broken original and redesigned without its nut. The creator explicitly identifies C-Class W204 and E-Class W212 applications and specifies 0.1 mm layers and 100% infill; no other W212-generation body styles are stated. Compare the removed shaft and controller revision, use tough cabin-heat-resistant material, transfer and assemble the mechanism without damaging electronics and verify full rotary, tilt and press operation before driving.

Fits C-Class · W204 / S204 / C204 · E-Class · W212 / S212 / C207 / A207

Three-file stand for holding several stated box-mod device sizes in the centre-console cupholder. For this generation the creator instructs that the supplied disc be glued or screwed to the bottom of the stand and reports printing in PETG. Match the cupholder and device dimensions, use cabin-heat-resistant material, assemble the disc securely and confirm that the stand and device cannot obstruct the selector or controls, spill into sockets or become a projectile under braking.

Fits C-Class · W204 / S204 / C204

Two-piece floor-mat retaining clip published for this generation and shown on the physical carpet and anchor. The creator warns that small scaling changes may be needed for a particular printer and recommends checking the top and bottom separately so they snap securely without becoming inseparable. Compare the original anchor and mat opening, use tough cabin-heat-resistant material and confirm every mat remains flat, removable for service and completely clear of the accelerator, brake and clutch pedals.

Fits C-Class · W204 / S204 / C204

Snap-in phone mount designed and road-used in a 2011 vehicle with the Audio 50 APS navigation display cover. The creator states that it retains an iPhone 6 during acceleration, braking and cornering and allows charging, but the display cover cannot close while fitted. Match the Audio 50 APS cover and phone dimensions, use cabin-heat-resistant material, snap it in without forcing the cover and verify that the phone cannot obscure controls, airbags or the road or detach under braking.

Fits C-Class · W204 / S204 / C204

Custom dual cup holder designed by the creator for the 221-series S-Class and shown both loose and installed in the center console. The supplied single STL includes an S500 emblem and the creator notes that it can be printed in one color or with a multi-material system. The source does not state model year, wheelbase, facelift, steering side, console option, container diameter, material, print settings, or retention testing, so compare the console opening and surrounding controls before printing. Use cabin-heat-resistant material, protect the original trim, keep containers clear of the selector and switches, and verify that the holder and only cold, closed containers remain secure under braking before road use.

Fits S-Class · W221

Centre-console panel that replaces the ashtray box and cigarette lighter to mount a small aftermarket Bluetooth/MP3/SD/USB module. The creator states fitment for the 2006–2009 W164 ML280, ML320 and related variants and shows the physical panel installed. The file contains no electronics: use cabin-heat-resistant material, secure the module, independently fuse and insulate any wiring, and confirm selector and control clearance.

Fits M-Class / GLE · W164