Find your next part.

Original-style and gusset-reinforced replacement variants for the sprung latch inside the center-armrest storage cubby, with creator-stated fitment for 1992–1999 vehicles. The creator also states that mirroring the geometry makes it work for the glove-box latch in the same generation. The source photograph shows the physical latch mechanism and child piece. Independent inspection found the gusseted STL non-watertight, so repair and validate that mesh before slicing. The author reports that commissioned ABS versions lasted about 18 months despite embedded steel wire and changed to SLM 316L stainless steel for expected long-term durability. If printing in polymer, use a tough cabin-heat-resistant material, keep a spare, and verify reliable spring engagement and positive latching before use. Work over a clean surface to avoid losing the original spring; a replacement spring may require a carefully filed groove in the post.

Fits S-Class · W140 / C140

Speaker adapter developed and used to install a Polk DB652 in a 2002 G500. The preserved author file is named as a rear speaker mount; the source states that the adapter bolts to the vehicle with the original hardware, the speaker uses its supplied screws and the same geometry serves the driver and passenger sides. Match the speaker basket and mounting pattern, protect wiring, use material suitable for cabin heat and vibration, tighten hardware evenly and confirm the speaker, trim and wiring remain secure without rattles.

Fits G-Class · W463

Replacement interior door-panel clip for 1990s vehicles. The source includes a physical image of the clip installed in the door-panel mounting point and a CAD render, but gives no material or print settings and no exact Mercedes child-component number. Match the original clip and panel hole, remove supports and sharp edges, press-fit without forcing brittle trim and confirm the panel is fully retained before driving.

Fits G-Class · W463

Storage tray for 1990s vehicles, shown fitted in the dashboard opening beside the audio unit. The author supplies divided and undivided STL variants plus the undivided STEP source. No material or print settings are stated. Compare the opening and adjacent switch/audio layout before printing, use material appropriate for cabin heat, deburr the retaining features and confirm the tray and stored objects cannot interfere with controls or become loose under braking.

Fits G-Class · W463

Custom dashboard mount for a period mobile telephone, developed on a 1999 roadster and shown installed beside the centre console. The creator modified the telephone lighting separately with a resistor, parallel LED groups, a coiled cable and a 12-to-4 V converter; those electrical modifications and the phone are not part of the model. Match the phone body and dashboard position, use cabin-heat-resistant material, protect trim and wiring, fuse and insulate any electrical work independently and confirm the mount and phone cannot obstruct controls or become loose under braking.

Fits SL · R129

Replacement sliding clip for the upper row of the lower door/body cladding, developed and tested on a 1999 roadster. The creator reports more than three months of exterior Texas use from 27–44 °C and testing to 233 km/h, specifies vertical print orientation, grid infill and 15% infill, and warns that higher infill reduced performance. The creator was told that similar cladding on 124- and 140-series cars may use it but could not confirm that fitment, so no cross-generation link is added. Compare the original upper clip and cladding rail, use UV-, heat- and impact-resistant material and confirm the panel remains secure at road speed.

Fits SL · R129

Three-piece replacement bushing for the 16 mm ball joint between the windscreen-wiper arm and motor linkage. The creator printed it in PETG at 100% infill, fitted it around the ball joint, bonded the pieces and recommends lubrication. Match the ball diameter and linkage version, use wear-, heat- and moisture-resistant material, preserve free articulation and bench-test full sweep, parking and stall behavior before wet-road use; inspect the bonded joint regularly.

Fits SL · R129

Replacement knob for the access cover on the high-mounted stop-lamp assembly. The creator instructs removing the broken knob base, bonding this print in its place and printing sideways for strength. The cited 1297500039 number identifies the surrounding lamp-cover assembly rather than this repair fragment and is not assigned. Use cabin-heat- and UV-resistant material, choose adhesive compatible with the original plastic and verify that the cover remains secure and the stop lamp operates correctly.

Fits SL · R129

Direct replacement for the hidden hinge base inside the leather-covered door-mounted cup holder, developed on a 300E from the 1984-1996 period. Source photographs show the physical base and cup-holder assembly. Match the door and holder variant, reuse the original covering and backing carefully, use tough cabin-heat-resistant material, and verify full folding travel, secure retention and unobstructed door operation.

Fits E-Class · W124 / S124 / C124 / A124

Replacement drain grommet for the plastic box below the right headlamp on the air-intake side. The creator states all 124-series chassis, a slightly tighter body fit and a changed drain shape. Use heat-, weather- and fluid-resistant flexible material, confirm the right-side box and opening, preserve an unobstructed downward drain path, and verify the grommet cannot admit water to wiring or the air intake.

Fits E-Class · W124 / S124 / C124 / A124

Standard- and loose-fit replacement grommets for mounting the hydraulic self-levelling suspension oil reservoir on estate cars. The creator identifies the exact child as A1299971681. These grommets support only the reservoir, not a suspension load path. Use oil-, heat- and vibration-resistant flexible material, match the mounting hole and reservoir pin, and inspect for leaks and secure retention after installation.

Fits E-Class · W124 / S124 / C124 / A124

Replacement grommet through which the radiator lower locating prongs pass. The source establishes 124-series fitment but provides only model imagery. This grommet isolates and locates the radiator; it is not a structural vehicle mount. Compare the original opening and radiator pin, use engine-bay heat-, coolant- and vibration-resistant flexible material, and confirm secure seating, fan clearance and leak-free hoses after installation.

Fits E-Class · W124 / S124 / C124 / A124

Two replacement shaft-lock variants for the headlamp-wiper motor assembly: K for SWF motors and L for SWF or Bosch motors. The creator tested both on original assemblies and documents the installed position. Identify the motor maker before printing, use heat- and weather-resistant material, preserve cable potting, and bench-test motor retention, full sweep and parking before road use.

Fits E-Class · W124 / S124 / C124 / A124

Direct replacement for the lower condenser mounting grommet identified by the creator as A2019970381. The source model intentionally simplifies fillets and tightens the fit for printing. Compare the original grommet and condenser pin, use heat-, weather- and vibration-resistant flexible material, and confirm the condenser is retained without metal-to-metal contact or stressed refrigerant lines.

Fits E-Class · W124 / S124 / C124 / A124

Replacement clip used in pairs to secure the lower engine wiring harness to the engine block; the creator notes that the same size also appears elsewhere. Exact routing varies with engine and model year, so compare the original clip and mounting point rather than inferring other positions. Use engine-bay heat-, oil- and vibration-resistant insulating material, avoid sharp wire contact and confirm the harness cannot reach hot or moving parts.

Fits E-Class · W124 / S124 / C124 / A124

Insert replacing the disassembled centre-console fader-switch mechanism to retain a USB extension cable from an updated head unit. The source supplies the insert model and console-fit imagery but no electrical hardware. Confirm the early console opening and cable connector, use cabin-heat-resistant insulating material, provide strain relief and fusing for the connected accessory, and keep wiring clear of the selector and original harness.

Fits E-Class · W124 / S124 / C124 / A124

Replacement grip for the thin wallet/spare key, designed to make the original key blade easier to turn. The print is only the external grip and does not reproduce the lock blade. Confirm the blade shoulder and grip fit, use tough cabin-heat-resistant material, retain the blade securely, and test gentle operation in each intended lock without forcing the cylinder.

Fits 190 Series · W201

Replacement covering/clip for retaining the vapour barrier behind the interior door panel. The creator explicitly identifies both 190-series and 124-series applications, supplies numbered and unnumbered geometry, and recommends glass-fibre-reinforced polypropylene with controlled support separation. The controlled material taxonomy does not include that polymer; nylon is listed only as a durable alternative and requires fit validation. EPC applicability maps the exact covering to both chassis families. Match the original profile, avoid tearing the moisture barrier, and confirm the door panel seats without bulging.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124

Custom dashboard air-vent adapter for a standard 52 mm temperature, voltage, oil-pressure or lambda gauge. The creator explicitly states fitment to both 190-series and 124-series vents. Confirm steering-side vent geometry, gauge depth, wiring and hose routing; fuse electrical additions, avoid sharp edges and preserve driver visibility and remaining ventilation.

Fits 190 Series · W201 · E-Class · W124 / S124 / C124 / A124

Two-piece replacement shaft set for the mechanical speedometer drive. The creator printed it in PETG with a 0.2 mm nozzle, reports about 1,500 km of successful use, and notes that axle sanding may be required. The cited EPC number describes the complete speedometer-drive component and is not assigned to these printed internal pieces. Match the transmission drive version, avoid altering tooth geometry, and verify accurate speed indication and leak-free operation.

Fits 190 Series · W201

Replacement handle modeled after the original bonnet-release handle. Source photographs document the latch area and installed handle location. Compare the pivot and cable-end geometry, use tough cabin-heat-resistant material, preserve full cable travel, and verify the bonnet opens, closes and latches correctly before driving.

Fits 190 Series · W201

Replacement driver-side dashboard vent surround, supplied as both a complete model and a two-piece version for easier printing. The creator reports that it fitted but was not fully refined, warns that PLA deformed in summer heat, and says to mirror the part for left-hand-drive use. The complete STL appears about 25.4 times smaller than the split files when interpreted as millimetres, so verify source units and final dimensions in the slicer. Confirm steering side and vent geometry, print in heat-resistant material, and verify free vent-slider movement.

Fits 190 Series · W201

Adapter ring for fitting an Alpine SXE-1025S speaker to the original dashboard mounting points while retaining the original grille. Fitment evidence is specific to that speaker model. Check depth, terminals and grille clearance, use cabin-heat-resistant material, protect the dashboard and wiring, and secure the speaker so it cannot rattle or detach.

Fits 190 Series · W201

Service adapter for manually operating the sunroof emergency drive, with the vehicle-side internal profile and an external profile for a 13 mm socket. Confirm the drive version and engagement depth before use, choose tough material, turn only with controlled hand force, and stop if the roof binds; this adapter is not a substitute for correcting the underlying drive or cable fault.

Fits 190 Series · W201