Find your next part.

Two-piece cup holder replacing the original dashboard ashtray, explicitly designed for 903-series vans. The creator states that a spring must be added for the mechanism; source imagery shows the installed holder, loose physical parts, mechanism and CAD views. Use cabin-heat-resistant material and a securely retained spring, preserve controls and selector clearance and test only with closed cold containers until retention under braking is confirmed.

Fits Sprinter · W901–W905

Two-material push knob for operating the interior sliding-door latch, developed on a 2006 2500 van after the replacement handle tab failed. The source provides STL and 3MF variants plus photographs of the physical knob, and specifies flexible material sandwiched between rigid sections. Clean and repair a resistant latch mechanism rather than forcing it, use tough cabin-heat-resistant materials, confirm secure engagement and verify normal opening, closing and latching from inside and outside before use.

Fits Sprinter · W901–W905

Replacement holder for the warning triangle in a 903-series van. The creator supplies a printable file and one CAD source image but gives no body-style, market, mounting-fastener or crash-retention details. Compare the triangle case and mounting position, use tough cabin-heat-resistant material, reuse appropriate fasteners and verify the emergency equipment remains secure, accessible and unable to become a loose object.

Fits Sprinter · W901–W905

Four-piece phone-holder system that clips into the dashboard ashtray position, with a phone cradle, left and right support arms and a ball-interface console base. The creator explicitly states 903-series fitment and supplies CAD source views but no installed follow-up photograph. Confirm the ashtray opening, phone dimensions and ball interface, use cabin-heat-resistant material, keep the assembly clear of the selector and controls and verify the phone cannot detach or obstruct the driver under braking.

Fits Sprinter · W901–W905

Replacement bulb socket for the clearance/parking lamp in the headlamp, explicitly identified by the creator as A2108260582 for 208- and 210-series cars. The source provides one author-downloadable STL and one CAD image but no physical fit photograph. Official Mercedes parts-store metadata identifies the exact child as the clearance-lamp socket for CLK 208 and E-Class 210. Verify VIN and headlamp variant, use heat- and flame-resistant electrically insulating material, transfer the correct contacts and bulb without damaging insulation, and test retention, polarity, lamp output, sealing and heat behavior before road use.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Ten-card organizer sized for the eyewear/storage compartment in the centre console. The creator explicitly identifies 210-series fitment and notes compatibility with a separate mini-drawer, but provides only a CAD source image and does not establish other models. Use cabin-heat-resistant material, confirm compartment dimensions and lid travel, and ensure cards remain retained without obstructing the selector or other controls.

Fits E-Class · W210 / S210

Phone tray with an accessory USB charging socket for the rear centre-console cover position. The creator states 210-series use, 3M VHB or Tesa ACXplus adhesive mounting, and supplies the original-cover comparison plus the physical tray; no installed follow-up image is present. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain relief, preserve rear-console and seat travel, and verify adhesion and wiring clearance before use.

Fits E-Class · W210 / S210

Modular replacement for the centre-console ashtray insert, with USB-power and optional 50-cent coin-dispenser configurations. The creator states 210-series fitment, documents an installed dimensional correction, and specifies a 9 x 35 mm spring and adhesive for the dispenser components; source photographs show loose physical assemblies and the wired USB insert. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain-relieved wiring, keep conductors and coins isolated, and confirm selector and console clearances.

Fits E-Class · W210 / S210

Adapter for the original Nokia phone mounting point, intended to accept contemporary phone holders. The creator explicitly identifies 210-series fitment and supplies a photograph of the physical print. Confirm the factory cradle profile and the chosen holder interface, use cabin-heat-resistant material, secure the phone without obstructing controls or airbags, and verify it cannot detach under braking.

Fits E-Class · W210 / S210

Push-fit mechanical adapter that converts the smaller dashboard lighter opening to accept the larger socket insert shown by the creator. The creator supplies one STL and physical source images but does not state socket current, fuse rating or heat testing. Match the opening and chosen insert, use flame- and cabin-heat-resistant material, retain the original fused circuit limits, insulate all terminals, keep the socket clear of adjacent controls and stop use if the print softens, loosens or heats.

Fits C-Class · W202 / S202

Storage-bin replacement for the factory ashtray opening. The source notes that light from the original ashtray bulb can shine through light-coloured material and supplies one STL with source renders. Use opaque cabin-heat-resistant material if light bleed is undesirable, compare the ashtray opening and lamp clearance, deburr the edges and confirm the bin and stored items cannot interfere with the selector, controls or occupants or become loose under braking.

Fits C-Class · W202 / S202

Replacement pneumatic coupling for the vacuum-operated headlamp height adjustment, developed for a C180 after the original connector broke and leaked. The creator sealed the printed part with nail polish to make it airtight. Match both hose and headlamp ports, use fuel/oil/heat-resistant material suitable for engine-bay vacuum service, seal without obstructing the passages, leak-test the system and verify both lamps adjust and remain correctly aimed before night driving. The moulded fragment “012502” is preserved as evidence but is not treated as a complete Mercedes part number.

Fits C-Class · W202 / S202

Small retaining pin used by the creator to mount a threshold/door-sill trim panel on this vehicle generation. Source images show the printed pin beside original-style pins and at the sill mounting points. Compare the original pin, panel hole and body socket before printing; use a tough cabin- and weather-resistant material, remove sharp edges, press-fit without forcing brittle trim and confirm the sill panel is fully retained and cannot foul the door.

Fits C-Class · W202 / S202

Phone holder made for a Samsung Galaxy Note 4 and shown physically installed across the centre dashboard vents. Confirm the phone dimensions, vent geometry, hazard/control access and sight lines before use. Print in cabin-heat-resistant material, deburr all contact surfaces, avoid loading fragile vent vanes and verify the phone cannot detach, obscure the road or interfere with controls or airbags under braking.

Fits C-Class · W202 / S202

Cup holder for a cassette-deck opening, tested by the creator in this vehicle generation with 12 oz and 16 oz UK cups. Two OBJ variants are supplied: zero degrees and 25 degrees; the creator states the 25-degree version keeps a drink upright in this cabin. The stereo must remain in cassette-eject mode while fitted. Use cabin-heat-resistant material, verify the deck supports the holder without damage, keep liquids away from electrical controls and occupants, and test retention with a cold, closed container before road use; hot liquids and abrupt braking can cause burns or electronic damage.

Fits C-Class · W202 / S202

Original-style and gusset-reinforced replacement variants for the sprung latch inside the center-armrest storage cubby, with creator-stated fitment for 1992–1999 vehicles. The creator also states that mirroring the geometry makes it work for the glove-box latch in the same generation. The source photograph shows the physical latch mechanism and child piece. Independent inspection found the gusseted STL non-watertight, so repair and validate that mesh before slicing. The author reports that commissioned ABS versions lasted about 18 months despite embedded steel wire and changed to SLM 316L stainless steel for expected long-term durability. If printing in polymer, use a tough cabin-heat-resistant material, keep a spare, and verify reliable spring engagement and positive latching before use. Work over a clean surface to avoid losing the original spring; a replacement spring may require a carefully filed groove in the post.

Fits S-Class · W140 / C140

Speaker adapter developed and used to install a Polk DB652 in a 2002 G500. The preserved author file is named as a rear speaker mount; the source states that the adapter bolts to the vehicle with the original hardware, the speaker uses its supplied screws and the same geometry serves the driver and passenger sides. Match the speaker basket and mounting pattern, protect wiring, use material suitable for cabin heat and vibration, tighten hardware evenly and confirm the speaker, trim and wiring remain secure without rattles.

Fits G-Class · W463

Replacement interior door-panel clip for 1990s vehicles. The source includes a physical image of the clip installed in the door-panel mounting point and a CAD render, but gives no material or print settings and no exact Mercedes child-component number. Match the original clip and panel hole, remove supports and sharp edges, press-fit without forcing brittle trim and confirm the panel is fully retained before driving.

Fits G-Class · W463

Storage tray for 1990s vehicles, shown fitted in the dashboard opening beside the audio unit. The author supplies divided and undivided STL variants plus the undivided STEP source. No material or print settings are stated. Compare the opening and adjacent switch/audio layout before printing, use material appropriate for cabin heat, deburr the retaining features and confirm the tray and stored objects cannot interfere with controls or become loose under braking.

Fits G-Class · W463

Custom dashboard mount for a period mobile telephone, developed on a 1999 roadster and shown installed beside the centre console. The creator modified the telephone lighting separately with a resistor, parallel LED groups, a coiled cable and a 12-to-4 V converter; those electrical modifications and the phone are not part of the model. Match the phone body and dashboard position, use cabin-heat-resistant material, protect trim and wiring, fuse and insulate any electrical work independently and confirm the mount and phone cannot obstruct controls or become loose under braking.

Fits SL · R129

Replacement sliding clip for the upper row of the lower door/body cladding, developed and tested on a 1999 roadster. The creator reports more than three months of exterior Texas use from 27–44 °C and testing to 233 km/h, specifies vertical print orientation, grid infill and 15% infill, and warns that higher infill reduced performance. The creator was told that similar cladding on 124- and 140-series cars may use it but could not confirm that fitment, so no cross-generation link is added. Compare the original upper clip and cladding rail, use UV-, heat- and impact-resistant material and confirm the panel remains secure at road speed.

Fits SL · R129

Three-piece replacement bushing for the 16 mm ball joint between the windscreen-wiper arm and motor linkage. The creator printed it in PETG at 100% infill, fitted it around the ball joint, bonded the pieces and recommends lubrication. Match the ball diameter and linkage version, use wear-, heat- and moisture-resistant material, preserve free articulation and bench-test full sweep, parking and stall behavior before wet-road use; inspect the bonded joint regularly.

Fits SL · R129

Replacement knob for the access cover on the high-mounted stop-lamp assembly. The creator instructs removing the broken knob base, bonding this print in its place and printing sideways for strength. The cited 1297500039 number identifies the surrounding lamp-cover assembly rather than this repair fragment and is not assigned. Use cabin-heat- and UV-resistant material, choose adhesive compatible with the original plastic and verify that the cover remains secure and the stop lamp operates correctly.

Fits SL · R129

Direct replacement for the hidden hinge base inside the leather-covered door-mounted cup holder, developed on a 300E from the 1984-1996 period. Source photographs show the physical base and cup-holder assembly. Match the door and holder variant, reuse the original covering and backing carefully, use tough cabin-heat-resistant material, and verify full folding travel, secure retention and unobstructed door operation.

Fits E-Class · W124 / S124 / C124 / A124