The parts catalog
Find your fit. Download a free file or choose a maker to print and ship your part.
2,521 matching parts
Free files. Made for your car.
C3D–01067Flexible replacement for BMW rubber buffer 51466967605, creator-tested on an i3 and catalogued for F45, E81/E87, F20/F21, I01, and X1 E84. Print in approximately 85A TPU and cut out the temporary support tab after printing. Within the combined E8x generation, documented fitment is E81/E87 only.
Fits 1 Series · E81 / E82 / E87 / E88 · 1 Series · F20 / F21 · 2 Series · F45 / F46 Active / Gran Tourer +2
C3D–01066Organizer tray for the compartment beneath the armrest in right-hand-drive BMW F45 Active Tourer and F46 Gran Tourer models. The source photograph shows the printed tray installed; this fitment is RHD-specific.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01065Four support-free mounting-base variants that clip into the small center-console storage pocket of BMW F45/F46 models. Includes fixed and rotating plates; rotating versions use an M5 nut and 12–20 mm bolt. Use PETG, ASA, or ABS rather than ordinary PLA.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01064Replacement hook that retains the cargo cover in position on the BMW F45 2 Series Active Tourer. Creator photographs show the physical hook installed; compare mounting orientation and clearances before fitting.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01063Replacement linkage between the rear center-console vent thumbwheel and airflow flap on BMW F45/F46 Active Tourer and Gran Tourer, including pre-LCI and LCI. Remove the vent assembly for access, verify linkage orientation, and use a cabin-heat-resistant material.
Fits 2 Series · F45 / F46 Active / Gran Tourer
C3D–01062Cup-holder extension designed and physically installed in a BMW F22 2 Series to move large 32-ounce cups clear of the dashboard while retaining the original recess as small-item storage. Plain and roundel variants are included. The creator reports good retention with a small shim and uses heat-resistant PETG-CF. Verify fit, cup stability, and clearance from controls before driving.
Fits 2 Series · F22 / F23 / F87
C3D–01061Cup-holder insert for 250 ml beverage cans in BMW F22 and F87 interiors. The creator uses the matching design in an F87 M2 and provides installed physical views. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the can remains stable without obstructing nearby controls.
Fits 2 Series · F22 / F23 / F87
C3D–01060Cup-holder insert for 330 ml beverage cans in BMW F22 and F87 interiors. The creator uses it in an F87 M2 and shows both the empty insert and a can seated in it. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the can remains stable without obstructing nearby controls.
Fits 2 Series · F22 / F23 / F87
C3D–01058Round and splined clutch-alignment tool variants designed for BMW N55 cars with the GS6 manual transmission. The creator printed the tool for a 2015 F22 M235i clutch replacement and verified the splined version during installation. Source fitment also names N55 E82, E9x, F3x, F10/F11, and F22/F23 cars. Use only on the specified engine/transmission combination, compare pilot and spline dimensions before use, and do not treat the printed tool as a torque-bearing service tool.
Fits 1 Series · E81 / E82 / E87 / E88 · 2 Series · F22 / F23 / F87 · 3 Series · E90 / E91 / E92 / E93 +3
C3D–01057Cup-holder insert developed and physically used in a 2016 BMW M2 F87 to keep narrow bottles upright. The source shows the printed insert installed beside a bottle. Print in PETG, ASA, ABS, or another cabin-temperature-resistant material and confirm the bottle remains secure without obstructing nearby controls.
Fits 2 Series · F22 / F23 / F87
C3D–01056Drop-in organizer tray for the deep center-armrest storage compartment of the BMW 1 Series F70 (2024 onward). Dedicated sections hold coins, keys, charging cables, and a French motorway toll tag. The creator's photographs show the printed organizer installed in the armrest and loose for inspection. Use a cabin-temperature-resistant material and confirm that the armrest closes and latches normally without pinching cables.
Fits 1 Series · F70
C3D–01055Custom-fitted charging pad for the center-console storage recess of the BMW 1 Series F70 (2024 onward). The creator shows the finished pad, its underside with the charger electronics, and the completed installation in an F70. It requires an INIU 15 W Qi charger, careful disassembly, and a shortened USB-C lead soldered to the charger PCB. Use a heat-resistant material, have the electrical work performed by a competent person, insulate and strain-relieve all connections, and stop use immediately if the charger or phone overheats.
Fits 1 Series · F70
C3D–01054Cup-holder phone stand with a Lightning-cable passage, documented by the creator for BMW F20 1 Series and F30/F31 3 Series interiors. The gallery shows the stand installed, holding phones, and routing the charge cable. Add a thin foam or rubber liner as suggested, use a heat-resistant cabin material, and confirm secure phone retention before driving.
Fits 1 Series · F20 / F21 · 3 Series · F30 / F31 / F34 / F80
C3D–01053Adapter that clips around the BMW F20 center ventilation grille and accepts the creator's screw-mounted phone cradle. Multiple source photographs show the current revision installed. Use ASA, ABS, nylon, or another high-temperature material; inspect the clips for cracking and ensure the phone does not obstruct controls, airbag deployment, or driver visibility.
Fits 1 Series · F20 / F21
C3D–01052Two-piece clamp eyelet that repairs a broken parcel-shelf lifting cord on a BMW F20 LCI II without replacing the complete shelf. The creator shows the installed repair and supplies an original-project file alongside the printable mesh. Cut the cord only after confirming final length; use fine layers, verify that the clamp closes fully, and add adhesive if needed.
Fits 1 Series · F20 / F21
C3D–01051Reusable washer-fluid filler funnel for the BMW F20 filler neck. This revision adds an O-ring groove for a stable, sealed seat, and the source image shows the printed funnel in use while filling the reservoir. Select a fluid-compatible material and remove the funnel before closing the bonnet.
Fits 1 Series · F20 / F21
C3D–01050Two-piece intake opening developed and physically fitted to the airbox of a BMW F20/F21 1 Series. The creator states that it is intended to add intake sound, not power; the cutting profile and finished insert are both included. Keep the factory filter path intact, use an engine-bay-temperature-resistant material, de-burr the airbox opening, and inspect the installation for secure retention and contamination paths before running the engine.
Fits 1 Series · F20 / F21
C3D–01049Two-piece key tray shaped for the BMW F20 and F21 1 Series cup holder. The body and upper tray are bonded after printing, and the creator shows the assembly installed both empty and holding a key. Use a heat-resistant cabin material and verify that the tray remains secure before driving.
Fits 1 Series · F20 / F21
C3D–01046Measured replacement door-lock knob for a BMW F20 1 Series. The creator modeled the original knob directly, printed it, and shows the replacement installed on the door lock pin. Confirm the bore and free lock movement before use.
Fits 1 Series · F20 / F21
C3D–01043Two-piece replacement for the left dashboard air-vent position in a BMW E87, combining the vent housing with a round gauge/display holder. The creator's gallery shows the assembly installed in the vehicle. Confirm the instrument diameter and preserve safe driver visibility before installation.
Fits 1 Series · E81 / E82 / E87 / E88
C3D–0104236 mm, half-inch-drive oil-filter housing socket physically tested on the M47 diesel engine in a BMW E87 1 Series. The creator printed it at 90% infill, shows it seated on the filter cap, and reports successful use. Use a tough material, inspect the drive and hex surfaces before use, and replace the print if it shows cracking or rounding.
Fits 1 Series · E81 / E82 / E87 / E88
C3D–01041Two-piece removable cup holder for early BMW 1 Series door pockets. A separate interference-fit hook supports the holder in the door pocket; the creator sized it for takeaway cups and drinks cans and supplied a physical print photograph. Print in PETG or ABS for cabin heat resistance and confirm retention before driving.
Fits 1 Series · E81 / E82 / E87 / E88
C3D–01040Three-piece cup-holder assembly tested in a 2010 BMW E87. It relocates the drink above the original low cup recess so taller containers can be used without the armrest interfering. The retained package contains the adapter, bridge, and cup cradle. Use a heat-resistant cabin material and verify secure engagement before driving.
Fits 1 Series · E81 / E82 / E87 / E88
C3D–01039Direct replacement cap for the automatic-headlight rotary switch used in BMW E82 and E88 1 Series, E90/E91/E92/E93 3 Series, and E84 X1 interiors. The keyed hex and rotation stop reproduce the functional interface, and the creator shows the printed knob installed. Reuse the original switch mechanism; no complete headlight-switch assembly is included.
Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E90 / E91 / E92 / E93 · X1 · E84