Find your next part.

i bought RHD mirrors to my LHD e46 non-M Coupe and I created this raisers in order to get a better view angles (close to regular mirrors). This can be use to rise the angle of either side of the mirror and can be used in both mirrors. So with this you can "transform" RHD to LHD and viceversa. Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46

Greetings. At the moment, the model has already been strengthened and differs from the photo! There was a lot of window play in my E46. the glass rose heavily and crookedly. after disassembling the power window, it became clear that there was strong wear and tear and a large backlash. The brace does not come as a separate spare part, and you cannot buy an official one separately. My model is not perfect, it is robust, reinforced. Copes with its function. Window regulator carriage, right door, farthest from the motor v7. home plate (m) the following model, using the native metal plate in the link Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46

Cupholder insert for the rear armrest of BMW E46. The backing is inserted under the leather. Use the backing to mark the location for your cuts. A single slit in the center "web" is also needed to get the backing into the armrest. Carve out the foam as needed to clear the cupholder. Insert the backing, insert the cupholder and use 6 wood screws to hold them together. The screws I used have 4mm outer thread. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Many of these filters for the windshield washer reservoir get's broken and fall down into the water. The design is using the filter of the old holder and fits nice into your windshield water reservoir. Cut of the filter from the old holder. Glue it on the bottom. Cut off everything protruding. Done! The bar helps you to get the filter out for cleaning. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Replacement upper retaining clip for the rear front-seat back panel, modeled from the surviving seat-panel clip profile and physically compared with the panel. The nearby V5BB Brombeer catalog number identifies the complete parent panel and is intentionally omitted. Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

The carpeted panel on the interior of the E46 touring hatch is tricky to remove, and often the retaining clips are broken. I have created these two clips which can be epoxied in place to return normal function. In order to use them, completely cut the broken part of the clips out as shown in the photo then, use an epoxy like JB Weld liberally - the holes provide a mechanical bond for the epoxy. Note there are a right and a left. I did not create the center clip. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

My wifes car was equiped with a Hard top, but during summertime the hardtop is removed and there were these big gaping holes in the plastic trim. Apparantly there is a cover that fits there, but they cost aroun €60-80, each.. Can't have it that way and i wont pay that crazy amount for some plastic. Designed my own and sanded and plastidipped in black.. Looks good enough for me.. If you don't want to make one self, search for these part numbers on ebay or your local bmw dealer. 51717022385 51717022386 PS: The bunny ears will break, so just break them of before mounting.. They never aligned up but the part will not fall away.. it is snugg fittment. :) Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

[*TIRES SQUEAL AROUND TIGHT BEND* "Ugh, there goes my polar pop!"] Don't let this be you! This E46 cup holder expander will give your large size beverage a more comfortable place to rest. I have designed this one using Fusion360's shape optimization (hence the crazy design). Feel free to edit as you please and make the cup holder fit your favorite oversize mug or water bottle using the attached Fusion360 File. Enjoy. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

I designed this valve shim placement tool to aid in my recent valve adjustment on my 2004 BMW E46 M3. After viewing the picture of this special tool online, I decided it wasn't worth the money to order one, so I purchased some magnets and printed one instead. The magnet I used is a 8mm(0.315") Diameter x 3mm(0.118") Height, and was embedded into the base during the printing stage. I used the color change feature of PrusaSlicer to stop the print before the top layer and inserted the magnet. I printed both parts out of PETG and glued them together with cyanoacrylate. The tool was tested on my engine and worked perfectly. I even did the hard to reach rear valves with this homemade tool. Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

A Friend of mine lost one of the adjustment Knobs of his E46 Cabrio, you can buy it for the bargain of 180€, after 1h of modeling in Fusion360 the cost sank to 50ct a piece Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

My wind screen mounts got old and broke off, and I don't have a wind screen. These are designed to cover up the gaping hole. Not a perfect fit but definitely good enough - it won't fall out. PETG or ABS required for a hot car. Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

This is an updated set of Murat's clips which fit on the facelifted E46 kidney grills (My car is a 2002 325i wagon) and work without any filing / cutting / modification of the 3D printed part. How to use: Follow Murat's instructions for trimming the existing clip sockets on the kidney grill plastic (leaving ~1mm left + socket depth). Install as suggested by them (use a small flathead screwdriver or similar to pry the metal tabs of the hood into the printed groove on the clips. My printed parts are numbered and lettered to indicate where they go on the grill. How to read the number/lettering: When standing in front of the car and looking at the grill, there is a Left and Right grill. On each Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

When I bought a E46 Compact it had broken rear shelf retaining clip. So whenever I opened the trunk the shelf would hang randomly in the air. Also it made closing the trunk hard, as it jammed between the trunk lid and the body of the car. So I decided to make a model of the broken shelf clip, that came with the car. It may need some sanding or filing to achieve a better fitment in the shelf steel tube. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Cap for BMW 3 Series E46 washer fluid reservoir. Excellent friction fit when printed in PETG Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Fixes the third brake light from falling off the glass. replaces the usually broken clips. Verify secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E46

I lost my cap some time ago and I found one here, but not for my model and not in design I wanted. Therefore I did model for my car. It is tested in e46 convertible, but probably will fit coupe and maybe also other models. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

I used it for my BMW E46 and it is very sturdy. You can use a 32mm Hex Nut or a 1/2" square wrench to open the oil filter cap. The Tool on the picture was an earlier smaller version but it broke. Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E36 · 3 Series · E46

Four-piece E36 bumper-inlet duct inspired by the Dinan layout and physically shown installed between the bumper opening and air filter. Print in heat- and impact-resistant material, bond the sections securely, and verify filter, fan, belt, water-ingress and road-clearance conditions on the exact car.

Fits 3 Series · E36

Protective cap for the upper front strut bearing on a BMW E36, physically shown printed and installed in the engine bay. Use engine-bay-rated material and confirm it clears the strut brace, nut and suspension movement.

Fits 3 Series · E36

Replacement spacer for the front drink recess in the BMW E36 factory centre-console cupholder, physically shown installed. The creator lists accessory number 82111469119, but it was not independently resolved to this printed subcomponent and is intentionally omitted.

Fits 3 Series · E36

Direct replacement retainer for the BMW E36 Touring tailgate trim, physically shown installed at the lower edge of the open tailgate. Print in a tough material and confirm every stud and clip seats without distorting the trim.

Fits 3 Series · E36

Rear-cap extension physically fitted to an original BMW E36 fog lamp to clear the cooling fan on an LED replacement bulb while retaining the stock cap. Check bulb legality, connector strain, weather sealing, lamp clearance and heat before road use.

Fits 3 Series · E36

50 mm inner-diameter service sleeve for pressing output-flange seals out of the 168 mm differential on a 1995 E36 318ti. The source shows the physical tool and flange. Support the housing correctly, keep the tool square, and do not reuse a damaged seal.

Fits 3 Series · E36

67 mm cupholder and 54 mm reducer for the square opening ahead of the armrest in an E36 Compact. The source shows both sizes physically installed with 250 ml and 500 ml cans. Verify handbrake, shifter and armrest clearance before use.

Fits 3 Series · E36