Find your next part.

Replacement gear set for BMW E30 VDO odometers, physically shown in the cluster. The common small gear duplicated by the MotoMeter source was removed from this submission during global hash preflight.

Fits 3 Series · E30

Spinning replacement knob and glue-in collar made for the manual sunroof crank of a 1985 BMW E30. The creator shows the finished print on the crank. Dry-fit and keep adhesive away from the rotating shaft; no other year or chassis is claimed.

Fits 3 Series · E30

Phone-mount bracket for the factory accessory cup-holder socket in BMW E81, E82, E87, and E88 interiors. The current creator photographs show the bracket installed with a circular magnetic phone interface and also show the loose physical print. Only the bracket is included; choose compatible phone hardware and confirm that the device does not obstruct controls or driver visibility.

Fits 1 Series · E81 / E82 / E87 / E88

Fitted storage tray for the Jeep Renegade center armrest. The unbranded STL and editable STEP version are included; source photos document the tray seated in the console.

Fits Renegade · BU

Pair of front license-plate brackets for a 2015 Grand Cherokee WK2 lower grille. Each bracket accepts a plate screw and fastens to the mesh with a zip tie, avoiding drilled holes; the creator documents the exact mounting location.

Fits Grand Cherokee · WK2

Flexible replacement dust cover for the automatic shifter gate in 2005–2010 Grand Cherokee WK and WH center consoles. The creator documents the installed fit and specifies NinjaFlex.

Fits Grand Cherokee · WK / WH

Two-piece replacement for the ashtray and accessory-socket panel in 1999–2004 Grand Cherokee WJ and WG center consoles. The layout supports five Carling switches, two seat-heater switches, and five accessory sockets while reusing the factory metal latches.

Fits Grand Cherokee · WJ / WG

Replacement cupholder for Grand Cherokee WJ and WG center consoles. Moving the cup openings rearward adds a small forward storage pocket; the creator verified the fit in a 2004 vehicle.

Fits Grand Cherokee · WJ / WG

Dashboard fascia blank for fitting a double-DIN radio to a Grand Cherokee WJ or export-model WG. The user cuts the final opening for the chosen head unit; the source documents the installed fit.

Fits Grand Cherokee · WJ / WG

Replacement transfer gear and pressure roller for the Grand Cherokee ZJ power-antenna drive. The creator installed the pair after the worn mechanism rattled and failed to extend fully.

Fits Grand Cherokee · ZJ / ZG

Switch plate for the ashtray opening in a 2000 Cherokee XJ. Functional five-hole and blank versions are included

Fits Cherokee / Liberty · XJ

Low-profile fog-light mount for a Wrangler JK aftermarket bumper where a winch interferes with the factory cup. It moves the original fog lamp forward approximately 13 mm.

Fits Wrangler · JK

Holder for a 14 mm aftermarket hands-free microphone in the factory UConnect microphone position of a Wrangler JK. Rounded and squared holder variants are included.

Fits Wrangler · JK

Sun Visor Retaining Clip designed for the 1996-2001 Toyota Camry (XV20). Replacement bracket designed and driver-side tested on a 1998 Camry

Fits Camry · 4th Gen

A printable three-position cup-holder separator documented by the original creator for 2014-2019 Argentina-market Corolla Toyota Corolla fitment. Title says 2104

Fits Corolla · 11th Gen

Snap-on covers for the reflective chrome climate-vent rings fitted from the 2014 facelift.

Fits Tundra · 2nd Gen

Four-piece organiser for the centre-console opening with two upright phone slots and a separate coin pocket.

Fits Hilux · 7th Gen

Two-piece reinforced replacement shell for the original two-button remote and key blade, assembled with four M2 screws and the original key screw.

Fits Land Cruiser Prado · 120 Series

Replacement push button for the left or right folding rear-seat release on 2010–2018 vehicles.

Fits 4Runner · 5th Gen

Two-piece replacement fuse-box cover with raised fuse-position text, modelled from a damaged original cover.

Fits Land Cruiser · 60 Series

Workshop tool for seating the oil seal in an LT230 transfer box. The creator printed it in PETG with a 2 mm shell and 50% infill.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Fits Defender · Td5

Wheel-centre reference tool that holds a tape measure at the true hub centre during suspension-height calibration.

Fits Discovery · 3

Workshop fitting tool for seating the rear hub seal squarely.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +3