Find your next part.

Drop-in organizer tray for the deep center-armrest storage compartment of the BMW 1 Series F70 (2024 onward). Dedicated sections hold coins, keys, charging cables, and a French motorway toll tag. The creator's photographs show the printed organizer installed in the armrest and loose for inspection. Use a cabin-temperature-resistant material and confirm that the armrest closes and latches normally without pinching cables.

Fits 1 Series · F70

Custom-fitted charging pad for the center-console storage recess of the BMW 1 Series F70 (2024 onward). The creator shows the finished pad, its underside with the charger electronics, and the completed installation in an F70. It requires an INIU 15 W Qi charger, careful disassembly, and a shortened USB-C lead soldered to the charger PCB. Use a heat-resistant material, have the electrical work performed by a competent person, insulate and strain-relieve all connections, and stop use immediately if the charger or phone overheats.

Fits 1 Series · F70

Reusable washer-fluid filler funnel for the BMW F20 filler neck. This revision adds an O-ring groove for a stable, sealed seat, and the source image shows the printed funnel in use while filling the reservoir. Select a fluid-compatible material and remove the funnel before closing the bonnet.

Fits 1 Series · F20 / F21

Two-piece intake opening developed and physically fitted to the airbox of a BMW F20/F21 1 Series. The creator states that it is intended to add intake sound, not power; the cutting profile and finished insert are both included. Keep the factory filter path intact, use an engine-bay-temperature-resistant material, de-burr the airbox opening, and inspect the installation for secure retention and contamination paths before running the engine.

Fits 1 Series · F20 / F21

Two-piece key tray shaped for the BMW F20 and F21 1 Series cup holder. The body and upper tray are bonded after printing, and the creator shows the assembly installed both empty and holding a key. Use a heat-resistant cabin material and verify that the tray remains secure before driving.

Fits 1 Series · F20 / F21

Measured replacement door-lock knob for a BMW F20 1 Series. The creator modeled the original knob directly, printed it, and shows the replacement installed on the door lock pin. Confirm the bore and free lock movement before use.

Fits 1 Series · F20 / F21

36 mm, half-inch-drive oil-filter housing socket physically tested on the M47 diesel engine in a BMW E87 1 Series. The creator printed it at 90% infill, shows it seated on the filter cap, and reports successful use. Use a tough material, inspect the drive and hex surfaces before use, and replace the print if it shows cracking or rounding.

Fits 1 Series · E81 / E82 / E87 / E88

Two-piece removable cup holder for early BMW 1 Series door pockets. A separate interference-fit hook supports the holder in the door pocket; the creator sized it for takeaway cups and drinks cans and supplied a physical print photograph. Print in PETG or ABS for cabin heat resistance and confirm retention before driving.

Fits 1 Series · E81 / E82 / E87 / E88

Direct replacement cap for the automatic-headlight rotary switch used in BMW E82 and E88 1 Series, E90/E91/E92/E93 3 Series, and E84 X1 interiors. The keyed hex and rotation stop reproduce the functional interface, and the creator shows the printed knob installed. Reuse the original switch mechanism; no complete headlight-switch assembly is included.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E90 / E91 / E92 / E93 · X1 · E84

Three-piece service-tool set for BMW N42, N46, and N46T engines: intake camshaft lock, exhaust camshaft lock, and the creator's strengthened M8-bolt VANOS gear counter-holder. The creator reports using the tools repeatedly and revised the counter-holder for the specified tightening procedure. This is an engine-specific workshop aid, not a substitute for BMW service information: inspect every print before use, follow the applicable repair procedure and torque sequence, and stop if any cracking or deformation is visible.

Fits 1 Series · E81 / E82 / E87 / E88

Cup holder developed and physically installed for a first-generation BMW 1 Series interior. The retained files are the latest creator-supplied right- and left-hand supported variants; earlier revisions are preserved in the source archive but are not submitted. Use a heat-resistant cabin material and confirm local clearance before driving.

Fits 1 Series · E81 / E82 / E87 / E88

Replacement exterior trim bezel for the roof antenna on a Jeep Commander. The creator updated the geometry for fit and documents the broken original beside the printed replacement.

Fits Commander · XK / XH

Replacement actuator plug for the Jeep Commander rear-seat release lever. Without the plug the seat release does not operate; the printable geometry directly replaces the discontinued original component.

Fits Commander · XK / XH

Adapter designed for the rear HVAC outlet in a 2007 Jeep Commander. It accepts 1-1/8-inch bilge/discharge hose to route air toward a rear child seat, and the source documents the installed setup.

Fits Commander · XK / XH

Replacement cap for a missing automatic shifter-knob insert, designed to fit a 2006 Jeep Commander.

Fits Commander · XK / XH

Replacement access flap for the Jeep Commander front wheel-well liner. The source gallery documents the printed panel and its installation in the liner opening.

Fits Commander · XK / XH

Replacement back shell plate for the rear camera assembly on a Jeep Renegade.

Fits Renegade · BU

Pair of rear license-plate mount extenders for securing a standard US Washington plate to all four sockets on a Jeep Renegade. Each accepts a press-fit M6 nut and uses short low-profile screws.

Fits Renegade · BU

Replacement key/tool for operating the Jeep Renegade MySky removable roof panel. Minor filing may be needed to tune the fit for a particular printer.

Fits Renegade · BU

Replacement wheel-well access cover for servicing the fog lamp on a Jeep Renegade. The creator measured the surviving original and reports this more-rigid replacement working.

Fits Renegade · BU

Hand knob for removing the M8 spare-wheel retaining bolt in a Jeep Renegade without a separate tool.

Fits Renegade · BU

Replacement front plastic retainer for the Jeep Renegade cargo-cover lift string. The creator measured an intact counterpart and reports the printed piece fitting the vehicle.

Fits Renegade · BU

Sunglasses retaining clip dimensioned specifically for the sun visor in a 2015 Jeep Renegade.

Fits Renegade · BU

Replacement protective cap for the exposed windshield-wiper arm nut on a Jeep Renegade, recreated after the original cap was stolen.

Fits Renegade · BU