Find your next part.

Replacement angle bracket connecting the centre-console panel to the transmission-tunnel covering on earlier cars. The creator copied the broken original, identifies EPC position 44, and states that the original threaded insert and screw are reused. Confirm early-model console geometry, use tough cabin-heat-resistant material, and tighten only enough to retain the trim without cracking the bracket.

Fits 190 Series · W201

Replacement carrier plate for the exterior mirror glass, physically shown loose and installed on the mirror mechanism. The creator states that it accepts both twist-on and clip-on brackets. This is a mirror-glass support, not the complete mirror assembly; verify secure engagement, adjustment range, heating-wire clearance and an unobstructed field of view before driving.

Fits Z4 · E85 / E86

Replacement access cover for the oil-drain opening in the engine-compartment underbody screening, physically shown loose and installed by the creator. BMW catalogs identify this child cover as 51757261712, item 5 in the underhood-shield diagram; it is used on X3 F25 and X4 F26 applications, so both live generations are linked. The printed design uses lower U-nuts and hex screws rather than the original fastening method. Print in PETG or a higher-temperature engineering polymer, confirm the panel variant and VIN, and verify secure retention and clearance before driving.

Fits X3 · F25 · X4 · F26

Two-piece organizer tray for the storage compartment beneath the center armrest, with an optional flexible floor insert and an opening that preserves access to the USB-C port. The creator designed it on a 2023 eDrive40 and shows the physical tray installed empty, with a charging cable, and loose outside the vehicle. Use PETG, ASA, or another cabin-heat-resistant material for the tray and TPU for the optional insert; verify stable seating, cable clearance, and unobstructed armrest movement.

Fits i4 · G26

This fits a BMW F11 and maybe also other BMW cars from around 2015. If the old cable brakes, this is a replacement of the ring at the cap and the cable. The original ring has to be removed from the fuel cap. Be careful not to brake anything else then the turning ring. Use side cutting pliers or a similar tool. The put the new ring onto the fuel cap. If the ring does not fit you can also adjust the width in the attached model and re-export. I used TPU 95 for the print. Nozzle diameter can be 0.25 - 0.4, all work. I printed with supports but this leaves a rough finish. This also leads to the fact, that the ring does not slide as good as the original one. But overall it works. Don't forget to like if you like. Creator reports the TPU replacement fits and works on an approximately 2015 F11, while noting rough support surfaces can make the ring slide less freely. The editable FreeCAD source is retained for measured adjustment. Do not force the ring or damage the fuel cap. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Storage-tray set for the center-console recess in BMW E60 and E61 models. Variants include a blank tray for customization, the creator’s everyday layout, a three-coin layout, and a tray for a Hörmann HS M 2/4 garage-door remote with an additional small compartment. The creator reports that the tray fits the existing console recess well. The demonstrated print used Fiberlogy Impact PLA; PETG is also suitable, while ordinary PLA is not recommended for vehicle-cabin temperatures. Verify dimensions, secure retention, and unobstructed operation.

Fits 5 Series · E60 / E61

The mirror adjuster on my E39 stopped moving the mirror in left-right direction, however I could still hear the small motor working. After removing the mirror plate, I found a small plastic component broken. Of course you can't buy this part, only the whole assembly (the one where I marked the pins with red arrows) for 100 USD :). Based on the broken component, I copied the part and printed it. It works perfectly!! Please note that if you need this for up-down motion, you will need to mirror the part before printing. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Four clip-in replacement gear-knob shapes for the BMW E34 and the creator-listed classic BMW chassis. The design was developed around the common BMW latching stem and includes an installed physical example. Confirm the lever's clip profile and preserve full shift travel before driving; the grouped API fitments reproduce only chassis families explicitly listed by the creator.

Fits 1 Series · E81 / E82 / E87 / E88 · 3 Series · E30 · 3 Series · E36 +14

Small storage bin fitted beside the handbrake lever in a BMW F30 328i. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed vehicle operation.

Fits 3 Series · F30 / F31 / F34 / F80

This is a custom USB holder designed to replace the button blanking strip on a BMW E46 dashboard – the one next to the ASC/DSC button. It’s a remix of another model, but with serious upgrades: ✅ Now with 3 Holes : I added a third port so you can mount a standard car charger PCB . Just remove the plastic casing and drop in the board. Works perfectly with generic AliExpress/Amazon 12V USB chargers. 🔩 Rear Clamp with M3 Bolts : The back has a clamp system for a solid hold using M3 bolts and heat-set inserts (not required, but highly recommended). 📐 Includes STEP File : I reverse-engineered the original STL in Fusion 360 and included a clean STEP file for anyone who wants to customize it further Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

These are speaker adapter mounts for BMW E46 front doors. There is a mount for both the tweeter and woofer. The mounts are designed for a JL Audio C3-525 component set but I have included generic .stp files for the mounts to adapt the design for your speakers. The woofers are screwed into the printed adapter rings and then the factory mounting screws are used to fix them to the door card. The tweeters clip into the mount with a twist and are held with integrated springs. The tweeter mounts also re-use the factory screws to hold them to the door cards. Left and right are exactly the same and there is no need to mirror the mounts. These fit perfectly and I have had no issues after a month of i Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46

Replacement E30 exterior door and fender moulding clip. The creator reports that the imperfect reproduction holds tightly. Listed numbers 51131953927 and 51131965105 identify parent moulding assemblies, so no OEM number is assigned.

Fits 3 Series · E30

Replacement gear set for BMW E30 VDO odometers, physically shown in the cluster. The common small gear duplicated by the MotoMeter source was removed from this submission during global hash preflight.

Fits 3 Series · E30

Two-piece clamp eyelet that repairs a broken parcel-shelf lifting cord on a BMW F20 LCI II without replacing the complete shelf. The creator shows the installed repair and supplies an original-project file alongside the printable mesh. Cut the cord only after confirming final length; use fine layers, verify that the clamp closes fully, and add adhesive if needed.

Fits 1 Series · F20 / F21

Low-profile 17 mm ball mount developed for the BMW F20 1 Series center-console side panel. The creator attaches it with double-sided automotive foam tape, shows it installed with a phone holder, and reports no problems in use. Print in ASA, ABS, or another cabin-temperature-resistant material and keep the device clear of controls and driver sight lines.

Fits 1 Series · F20 / F21

Dashboard fascia blank for fitting a double-DIN radio to a Grand Cherokee WJ or export-model WG. The user cuts the final opening for the chosen head unit; the source documents the installed fit.

Fits Grand Cherokee · WJ / WG

Dashboard-Shelf Magnetic Phone Mount designed for the 2014-2019 Toyota Highlander / Kluger (XU50). Source identifies newer Highlander's dashboard shelf/USB-cover opening but omits year

Fits Highlander / Kluger · 3rd Gen

A printable rear marker-light gasket documented by the original creator for AE92 Toyota Corolla fitment. Print in TPU

Fits Corolla · 6th Gen

Replacement ball connector for the 1984–1986 Celica Supra fog-light adjustment assembly, reported successfully printed and fitted by its designer.

Fits Supra · 2nd Gen

Snap-on covers for the reflective chrome climate-vent rings fitted from the 2014 facelift.

Fits Tundra · 2nd Gen

Replacement trim cap for the screw opening in the interior door-handle surround, modelled from a 2002 vehicle.

Fits Tacoma · 1st Gen

Replacement folding cup-holder assembly for the centre console, supplied in standard and inverted print orientations.

Fits Land Cruiser Prado · 90 Series

Replacement insert divider for the centre-console cup holder used with the shared instrument-panel cup-holder support.

Fits Land Cruiser Prado · 120 Series · Lexus GX · 470

Multi-piece phone mount that replaces the dashboard clock insert. Files include stud and printed-ball mounting options

Fits 4Runner · 3rd Gen