Every printable part.

Replacement retaining clip for the interior door wood trim. The creator identifies exact 220-series fitment, recommends flexible FilaFlex material, and the preserved source photographs show the loose printed clip, the wood trim installed and the door with the trim removed. The creator does not provide a molded Mercedes number. EPC evidence lists several position-specific clips and clamps around W220 door and pillar panelling, but does not establish which exact serviced child this geometry reproduces, so no OEM number is assigned. Compare the original clip, door position, trim profile and production/option version, fit without forcing the veneer, and confirm the wood trim is fully retained without rattles or interference.

Fits S-Class · W220

Replacement handle for adjusting the front-seat position after the creator’s original handle broke. The source explicitly identifies the first-generation SUV and includes a photograph of the printed handle installed beneath the seat. This is a convenience-control handle, not a structural seat or restraint component; compare the socket and lever travel before use.

Fits M-Class / GLE · W163

Two rear third-brake-light cover variants. The creator recommends the file ending in “n2” for better fitment and specifies ABS rather than PLA. Exact fitment evidence is limited to the first-generation SUV; confirm the lamp housing and retention points before installation.

Fits M-Class / GLE · W163

Three author files for replacement supports and clip geometry used on the front door trim. The creator states that the installed replacement remained in service for two years without a problem. Exact evidence is limited to the front doors of the first-generation SUV; compare the removed support and clip positions before installation.

Fits M-Class / GLE · W163

Internal replacement gear for the original blend-door actuator used in the creator’s ML 320. The source identifies A1638200108 as the complete actuator, not as this printed child gear, so that parent assembly number is not assigned. The creator warns that aftermarket motors may differ, tolerances are very tight, and sizing may need adjustment. Print in ABS at 100% infill; PLA is explicitly not recommended. Mark the metal-shaft position before disassembly, reinstall the gear with the flat side up, and preserve the original actuator orientation.

Fits M-Class / GLE · W163

Three-piece rear headlamp lid made after the creator lost the lid on an ML 270. Print the two rigid lid pieces in PETG or ABS, glue them together after removing support material beneath the hooks, and print the sealing insert in a flexible material. The creator suggests five perimeters and 50% infill for the first rigid piece, two perimeters and 10% infill for the second, and three perimeters and 10% infill for the flexible insert. The insert may be a tight push fit. Exact evidence is for the creator’s ML 270; confirm the headlamp housing before use.

Fits M-Class / GLE · W163

Two author variants of the left/right rear-bumper opening cover for the pre-facelift (phase 1) vehicle. Source photographs show loose printed covers and installed results. Fitment is not established for facelift bumpers or alternative bumper packages; compare the opening, tabs and side before printing.

Fits M-Class / GLE · W163

Two rear headlamp covers—one oblong and one small round cover—made by the creator for their first-generation SUV. The creator states that the small round cover needs light sanding to reduce visible faceting and recommends finishing the printed surfaces with varnish. Confirm headlamp housing and cover geometry before use.

Fits M-Class / GLE · W163

Retaining-clip variants for the exterior trim strip below the headlamp. Exact source fitment is the first-generation SUV; the creator includes an elongated version that held the strip more securely on their vehicle. Three author OBJ variants are supplied. Compare the original clip and trim engagement before choosing a file.

Fits M-Class / GLE · W163

Replacement windshield-washer-fluid reservoir cap proven by the creator on a 1999 first-generation SUV. The source reports that the original cap crumbles with age and that the replacement was printed successfully in dual-colour ABS; the colour change was made 1 mm into the print. Verify the cap profile against the vehicle before installation.

Fits M-Class / GLE · W163

Replacement left retaining hook/clip for the rear trim panel of a front seat. The creator identifies the exact child as A2089130172 for the 208-series and states that the model can be mirrored in the slicer for the opposite side. Mercedes official evidence calls A2089130172 the left hook, and PartSouq search evidence corroborates its front-seat-trim function. The OEM number applies only to the supplied left-side geometry; no right-side number is inferred for a mirrored print. Seat type, upholstery and option differences can affect fit, so verify by VIN and compare the original before fitting.

Fits CLK · C208 / A208

Second-version 150 mm phone holder published by the creator specifically for the CLK 208-series. The preserved source provides the author STL and a CAD image but no installed photograph, mounting instructions, material recommendation or body/facelift limitation. Compare the geometry and attachment area with the vehicle before printing, test retention at low speed, and keep the device clear of airbags, controls and the driver's sight line.

Fits CLK · C208 / A208

Replacement trim insert for the wind-deflector net opening of the late-1990s CLK convertible, modeled after the creator broke the original while removing the rear trim. The source shows the original and replacement together and the printed part installed. Mirror the supplied model in the slicer for the opposite side, then sand, prime and paint as needed. Transfer the original small flap and spring to the print; the creator does not publish a separately serviced Mercedes child number, so no wind-deflector or rear-trim parent assembly number is assigned. Confirm A208 trim and side geometry before installation.

Fits CLK · C208 / A208

Rear-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Front-position exterior cover for the side-skirt jacking opening, published for the CLK 208-series and shown installed on the creator's photographed coupe trim. Print vertically with supports and three wall lines to strengthen the hooks, using ABS or a similarly suitable material as the creator recommends. The source does not identify side, facelift, AMG/standard trim, option code or an exact molded number; compare the original opening and retainers before use. No OEM number is inferred from the cover's location.

Fits CLK · C208 / A208

Replacement stop/buffer reproduced by the creator as A2107500326 and explicitly tagged for CLK 208-series and E-Class 210-series cars. Mercedes official evidence identifies this exact child as an Anschlag (stop), with independent parts evidence describing a deck-lid/trunk-lid buffer. The supplied geometry is labeled with A2107500326; the earlier A2107580944 supersession is not assigned to the print. C208 coupe and W210 body/production applicability can vary, so verify the exact child by VIN and compare the original before fitting. The source does not state material, installation torque or physical validation.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Passive phone cradle that the creator explicitly states fits the ventilation grilles of the CLK 208-series and E-Class W211 sedan. It snaps into the grille without tools or vehicle damage, accepts an iPhone with or without a case, and leaves a lower opening for a charging cable. The creator notes that the model may be scaled independently to suit other phones; scaling can also change the grille engagement, so confirm a secure, non-damaging fit before driving and keep the device clear of controls, sight lines and airbags.

Fits CLK · C208 / A208 · E-Class · W211 / S211

Replacement fascia panel for the dashboard radio opening. The creator explicitly identifies the first-generation A-Class application and supplies a single printable panel. Verify radio and dashboard opening dimensions before printing and retain clearance for wiring, ventilation, controls and removal access.

Fits A-Class · W168

Holder for shopping bags in the boot. The download includes an original-form replacement and a strengthened alternative intended for heavier modern bags. Choose one variant rather than installing both, confirm that it seats in the original mounting point, and keep loads modest enough not to damage the surrounding trim.

Fits A-Class · W168

Replacement retaining clip for the door weatherstrip/seal. The creator designed it after the original clip broke and reports that it performs nearly as well as the original component. Use an automotive-temperature-capable material, compare the printed clip against an intact original before installation, and replace it if the seal is not held securely.

Fits A-Class · W168

Replacement floor air-ventilation grille identified by the creator as A63882701397C65. Source photographs show the physical grille installed in the carpeted floor opening. Use tough cabin-heat- and abrasion-resistant material, match the opening and colour/trim version, clear every slot and edge, seat the grille flush without trapping carpet, and confirm unrestricted airflow and clearance from feet, seats and movable interior fittings.

Fits Vito / Viano / V-Class · W638

Two internal replacement parts for the gear-selector mechanism. The creator identifies exact chassis fitment, supplies a physical source photograph and states that one O-ring is required to retain the assembly. The archived files were 3MF containers carrying misleading STL extensions and are preserved for upload with corrected .3mf filenames. Compare both original profiles and the selector version, use tough cabin-heat- and wear-resistant material, fit an oil-compatible O-ring of the correct size, and verify every gear position, detent, indication and interlock repeatedly with the vehicle stationary before road use.

Fits Vito / Viano / V-Class · W638

Replacement horizontal-fin assembly for the internal front dashboard vent nozzle. The creator reverse engineered the part from a van, had it printed in nylon and used it in the left vent; the source only suggests, rather than proves, that other front vents share the same internal geometry. Match the original left-side fin assembly before use, print in tough cabin-heat-resistant material, finish the pivots without removing retention features, and confirm every fin moves freely, stays aligned and does not obstruct airflow.

Fits Vito / Viano / V-Class · W638

Replacement stop for the rear/tailgate door locking mechanism, identified by the creator and model filename as 6387400003. Source photographs show the loose original-style child from both sides. Use a tough, weather- and impact-resistant material, compare the mounting and contact faces with the original, preserve latch and seal clearances, and verify the rear door closes, latches, opens and remains aligned without binding before driving.

Fits Vito / Viano / V-Class · W638