Every printable part.

Adapter for mounting a CubeNest PowerCube S1C0 or similar charger to the original cup-holder tray. The creator specifies a 200-series R170 car, printed it in ASA and supplies photographs of the physical adapter loose and installed with a charger. Confirm the tray and charger geometry, use cabin-heat-resistant material, keep controls and sight lines clear, route and fuse any charging cable safely and verify the holder and device cannot detach under braking.

Fits SLK / SLC · R170

Replacement headliner cap for the emergency retractable-roof lock, explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source image shows the physical cap installed; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived Texas cabin heat with little distortion. Match the access opening, use cabin-heat-resistant material and confirm the cap stays secure while remaining removable for emergency roof operation.

Fits SLK / SLC · R170

Replacement dashboard side vent explicitly identified for 1997–2004 SLK 230 Kompressor cars. The source photograph shows a physical vent installed in the dashboard; the creator recommends high-temperature PLA or PETG and reports a FILACUBE HT-PLA print survived a Texas summer with very little distortion. Match the side-vent opening and original vane function, use cabin-heat-resistant material and verify secure seating and unrestricted airflow and adjustment.

Fits SLK / SLC · R170

Single-piece rear wind-deflector pattern for CNC or laser cutting, shown in a source composite installed between the roll bars. The creator recommends at least 6 mm clear acrylic and reusable black zip ties. Confirm roll-bar spacing, cabin and retractable-roof clearances, round and polish all edges, use UV- and impact-resistant sheet, secure every tie with trimmed ends away from occupants and verify the panel cannot loosen or obstruct rearward visibility.

Fits SLK / SLC · R170

Replacement cap for the windscreen-wiper spindle screw on a 1997 SLK 230. Source photographs show the physical print loose, the uncovered spindle and the cap installed. Use UV-, weather- and heat-resistant material, match the spindle and nut dimensions, press on without disturbing wiper-arm torque, preserve full arm and bonnet clearance and verify secure retention through a complete wet-screen sweep.

Fits SLK / SLC · R170

Replacement button for the deteriorated rubber retainer on the door-sill/kick-panel trim. The creator states exact SLK 230 fitment and adds a locking feature to keep the print in place; the source supplies one STL and a CAD source image but no physical installation photograph. Print button-top down in tough cabin- and weather-resistant material, compare the panel and body socket, press-fit without forcing brittle trim and confirm the sill panel is fully retained and cannot foul the door.

Fits SLK / SLC · R170

Replacement cover plate for the motor inside the right exterior mirror, designed for model years 1998–2004 after a purchased spare did not fit. The source provides one STL and a CAD source image but no physical fit photograph. The creator warns that PLA breaks easily where the motor-screw heads press into the plate. Restrict use to the right mirror and matching motor, print flat-side down in tough cabin-heat- and weather-resistant material, fit screw heads gently and verify mirror adjustment, retention and full housing clearance.

Fits SLK / SLC · R170

Cup holder with an integral mounting tongue for the centre-armrest compartment. The creator states exact generation fitment and shows the physical print loose and installed, with the tongue pushed beneath the armrest screw. Use cabin-heat-resistant material, avoid damaging the armrest fastener or trim, confirm the lid and selector remain unobstructed and test retention only with a closed cold container before road use.

Fits SLK / SLC · R170

Replacement hinge set for both sun visors, developed from a 2003 car and explicitly stated by the creator for 1998–2004 SLK 230, SLK 320 and SLK 32 AMG models. Source photographs show the visor, original and printed hinges loose, and the completed visor installed. The creator used carbon-fibre HTPLA with 2 mm walls, 30% gyroid infill, supports and post-print annealing. Treat the supplied end-hinge files and combined hinge file as a set, compare every original piece, use tough cabin-heat-resistant material, smooth pivot surfaces and verify each visor holds securely without obstructing vision.

Fits SLK / SLC · R170

Replacement housing for the rear-door magnetic bumper on 2002–2006 vans. The creator cites original reference 901 740 03 16 but explicitly says this geometry is not an exact match; therefore that number is preserved only as a reference and is not assigned. Printing requires a layer pause to encase the reused original metal components, with TPU 64D or 95A specified. Inspect rust expansion, clean and protect the metal parts, confirm door alignment and magnetic retention and verify the housing cannot detach or interfere with complete door latching.

Fits Sprinter · W901–W905

Two-piece cup holder replacing the original dashboard ashtray, explicitly designed for 903-series vans. The creator states that a spring must be added for the mechanism; source imagery shows the installed holder, loose physical parts, mechanism and CAD views. Use cabin-heat-resistant material and a securely retained spring, preserve controls and selector clearance and test only with closed cold containers until retention under braking is confirmed.

Fits Sprinter · W901–W905

Replacement linkage rod for a dashboard air vent, explicitly identified for 901-series vans. Source photographs show the small printed rods and the matching vent assembly, but no steering-side or vent-position split is stated. Compare the original linkage length, pins and grille geometry, use tough cabin-heat-resistant material and verify every vane moves together through full travel without binding or detaching.

Fits Sprinter · W901–W905

Two-material push knob for operating the interior sliding-door latch, developed on a 2006 2500 van after the replacement handle tab failed. The source provides STL and 3MF variants plus photographs of the physical knob, and specifies flexible material sandwiched between rigid sections. Clean and repair a resistant latch mechanism rather than forcing it, use tough cabin-heat-resistant materials, confirm secure engagement and verify normal opening, closing and latching from inside and outside before use.

Fits Sprinter · W901–W905

Replacement holder for the warning triangle in a 903-series van. The creator supplies a printable file and one CAD source image but gives no body-style, market, mounting-fastener or crash-retention details. Compare the triangle case and mounting position, use tough cabin-heat-resistant material, reuse appropriate fasteners and verify the emergency equipment remains secure, accessible and unable to become a loose object.

Fits Sprinter · W901–W905

Four-piece phone-holder system that clips into the dashboard ashtray position, with a phone cradle, left and right support arms and a ball-interface console base. The creator explicitly states 903-series fitment and supplies CAD source views but no installed follow-up photograph. Confirm the ashtray opening, phone dimensions and ball interface, use cabin-heat-resistant material, keep the assembly clear of the selector and controls and verify the phone cannot detach or obstruct the driver under braking.

Fits Sprinter · W901–W905

Replacement limiting arm for the glove-compartment door, made for a 2003 van. The creator supplies an in-vehicle source photograph and a CAD view but no body, steering-side or market expansion beyond that vehicle. Compare the original arm, pivots and door travel, use tough cabin-heat-resistant material, avoid trapping wiring or documents and verify the door opens, closes and latches without overextending.

Fits Sprinter · W901–W905

Replacement bulb socket for the clearance/parking lamp in the headlamp, explicitly identified by the creator as A2108260582 for 208- and 210-series cars. The source provides one author-downloadable STL and one CAD image but no physical fit photograph. Official Mercedes parts-store metadata identifies the exact child as the clearance-lamp socket for CLK 208 and E-Class 210. Verify VIN and headlamp variant, use heat- and flame-resistant electrically insulating material, transfer the correct contacts and bulb without damaging insulation, and test retention, polarity, lamp output, sealing and heat behavior before road use.

Fits CLK · C208 / A208 · E-Class · W210 / S210

Ten-card organizer sized for the eyewear/storage compartment in the centre console. The creator explicitly identifies 210-series fitment and notes compatibility with a separate mini-drawer, but provides only a CAD source image and does not establish other models. Use cabin-heat-resistant material, confirm compartment dimensions and lid travel, and ensure cards remain retained without obstructing the selector or other controls.

Fits E-Class · W210 / S210

Phone tray with an accessory USB charging socket for the rear centre-console cover position. The creator states 210-series use, 3M VHB or Tesa ACXplus adhesive mounting, and supplies the original-cover comparison plus the physical tray; no installed follow-up image is present. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain relief, preserve rear-console and seat travel, and verify adhesion and wiring clearance before use.

Fits E-Class · W210 / S210

Modular replacement for the centre-console ashtray insert, with USB-power and optional 50-cent coin-dispenser configurations. The creator states 210-series fitment, documents an installed dimensional correction, and specifies a 9 x 35 mm spring and adhesive for the dispenser components; source photographs show loose physical assemblies and the wired USB insert. Use cabin-heat-resistant insulating material, a fused automotive-grade USB module and strain-relieved wiring, keep conductors and coins isolated, and confirm selector and console clearances.

Fits E-Class · W210 / S210

Adapter for the original Nokia phone mounting point, intended to accept contemporary phone holders. The creator explicitly identifies 210-series fitment and supplies a photograph of the physical print. Confirm the factory cradle profile and the chosen holder interface, use cabin-heat-resistant material, secure the phone without obstructing controls or airbags, and verify it cannot detach under braking.

Fits E-Class · W210 / S210

Replacement handle for the climate-control panel. The creator states exact 210-series use and provides four CAD views plus a printable part and an editing variant, but no installed photograph or detailed trim/market split. Compare the original handle, shaft and panel before printing, use cabin-heat-resistant material, keep the control mechanism free of debris, and verify full smooth travel and the correct setting indication after installation.

Fits E-Class · W210 / S210

Push-fit mechanical adapter that converts the smaller dashboard lighter opening to accept the larger socket insert shown by the creator. The creator supplies one STL and physical source images but does not state socket current, fuse rating or heat testing. Match the opening and chosen insert, use flame- and cabin-heat-resistant material, retain the original fused circuit limits, insulate all terminals, keep the socket clear of adjacent controls and stop use if the print softens, loosens or heats.

Fits C-Class · W202 / S202

Support for the interior third brake lamp, shown as a physical print and fitted at the base of the rear window. The source does not state body-style, market or production-break coverage, so compare the lamp, parcel shelf and rear-glass profile before printing. Use UV- and cabin-heat-resistant material, preserve the full illuminated area and wiring clearance, secure the lamp against vibration and verify operation and rear visibility before road use.

Fits C-Class · W202 / S202