Every printable part.

Replacement rear access cover for the high-beam bulb opening on facelift headlamp assemblies. The creator replicated a perished cover from a 2005 vehicle, physically printed the replacement in ABS and reused the original rubber seal. Public BMW catalog evidence identifies the serviced high-beam cover as 63 12 6 940 252 for facelift E53 headlamps. Use only on matching 10/2003-on headlamp assemblies, transfer an undamaged seal, use heat-resistant material and confirm a dry, secure seal before driving.

Fits X5 · E53

Replacement trim sleeve surrounding the interior door-lock pin. The creator modeled it as a solid, friction-fit alternative to the original slotted piece, physically compared the print with the original and shows it installed in the door top. It corresponds to BMW locking-button cover 51 41 8 408 567, used on front and rear E53 door trims. Print in a UV- and heat-resistant material, compare the sleeve and pin travel with the original, and ensure the lock pin moves freely before use.

Fits X5 · E53

Tapered adapter for mounting an aftermarket frameless Plateholder bracket to the original front bumper mounting surface. The creator designed it for a short German plate after removing the wide factory plate carrier and shows the printed adapters installed on the vehicle. Print one adapter for each attachment point, use suitable exterior-grade material and hardware, and confirm bumper style, plate dimensions, local visibility rules and secure retention before road use. This interfaces with aftermarket hardware and is not assigned a BMW OEM number.

Fits X5 · E53

Two-piece replacement dust cover for the steering-gear input shaft. The creator designed it specifically for the first-generation X5 steering rack and shows the printed cover installed around the shaft without removing the steering assembly. Print in a heat-resistant, tough material, secure the two halves as shown by the source, and verify full steering travel, shaft clearance and attachment security before driving. BMW does not catalog this input-shaft cover as a separately serviced child part, so no OEM number is assigned.

Fits X5 · E53

Replacement retaining clip for third-party winter floor mats. The creator designed and physically printed it after the supplied clip broke, and explicitly states it was used for the mats in a BMW X4 G02. Although G20 and G03 are suggested by the source, those fitments are not independently tested and are intentionally not linked. This is not represented as a genuine BMW component and no OEM number is assigned. Use a durable material such as PETG, ABS or nylon, compare the mating profile with the broken mat clip, and confirm that the mat is securely retained without interfering with pedal travel before driving.

Fits X4 · G02 / F98

Drop-in organizer for the small driver-side lower-dashboard compartment, with dedicated spaces for glasses, two valve-cap tools and a small lamp. The creator physically shows the organizer loose, loaded and installed in an X3 G01; the pictured M-style lettering is optional decorative geometry and is not a BMW trim or color claim. This is an aftermarket organizer rather than the surrounding storage-compartment assembly, so no parent number is assigned. The evidence shows a left-hand-drive layout; confirm LHD/RHD compartment geometry, trim and equipment, use a cabin-heat-resistant material and verify closure and pedal/control clearance.

Fits X3 · G01 / F97

Clip-on honeycomb cover intended to stop small objects entering the open ventilation duct beneath a front seat, physically shown loose and installed by the creator on a 2024 X3 G01. This is an aftermarket guard rather than a reproduction of a separately serviced BMW child component, so no duct or floor parent number is assigned. Creator evidence is limited to model year 2024; confirm seat position, duct profile, side and production configuration, preserve airflow and seat wiring clearance, and use a cabin-heat-resistant material.

Fits X3 · G01 / F97

Drop-in frame for the factory wireless-charging pad that keeps a phone centered while leaving the charging-status LED visible. The creator recreated it on a 2021 X3 G01 for phones up to approximately 75 x 155 mm and reports using it with a device larger than the original iPhone 15-sized insert. This is an aftermarket retainer rather than the cataloged charging tray, so no parent assembly number is assigned. Confirm charging-pad and phone geometry, option equipment, charging alignment, heat, clearance and retention before driving; use PETG, ABS, ASA or another cabin-heat-resistant material.

Fits X3 · G01 / F97

Two-piece mount for a Musway M6 V3 DSP/amplifier, physically shown installed in the left rear cargo-area electronics space. The creator developed it on an X3 G01 LCI with the HiFi sound system and states that it is not compatible with the Harman Kardon system; assembly uses two M3x10 countersunk fasteners, one M6x20 fastener and two factory bolts. This is an aftermarket equipment mount, not a reproduction of a BMW service part, so no parent electronics or trim number is assigned. Confirm G01 LCI body, HiFi rather than Harman Kardon equipment, cable clearance, ventilation, fastening and trim-panel closure before use.

Fits X3 · G01 / F97

Replacement covering cap for the rear-window wiper arm, 3D-scanned from the original and physically shown loose, compared with the original and snapped onto the arm. BMW catalogs identify the original child component as 61687407276, rear-wiper diagram item 6, for X3 G01/G01 LCI, X3 M F97/F97 LCI and iX3 G08; Hubauer records supersession to 61625A9D577. Use ABS, ASA, PETG or another UV- and heat-resistant material, compare the clip geometry, confirm by VIN and verify secure retention and full wiper travel.

Fits iX3 · G08 · X3 · G01 / F97

Multipart armrest-console tray for a MagSafe charging puck, physically shown installed in an X3 F25 and documented for 2011–2017 vehicles. The source includes original and current-puck top variants plus separate padding pieces; use only the matching top and padding set. This is an aftermarket charging accessory rather than a reproduction of a BMW service part, so no parent tray or telephone-option number is assigned. Use PETG, ABS or ASA for the body and TPU for padding as documented, verify S6NS/S6NW and earlier telephone-option console geometry, cable routing, heat, charging alignment and armrest closure before use.

Fits X3 · F25

Tall and short divider variants that create a small pocket in the armrest center-console storage compartment, with direct physical installation evidence. The creator warns that console shapes vary by equipment version and recommends removable adhesive for retention. This is an aftermarket divider rather than a reproduction of the complete BMW storage compartment, so no parent assembly number is assigned. Confirm the console shape and telephone-equipment configuration, use a cabin-heat-resistant material, and verify that the armrest closes and stored items cannot interfere with controls.

Fits X3 · F25

Replacement access cover for the oil-drain opening in the engine-compartment underbody screening, physically shown loose and installed by the creator. BMW catalogs identify this child cover as 51757261712, item 5 in the underhood-shield diagram; it is used on X3 F25 and X4 F26 applications, so both live generations are linked. The printed design uses lower U-nuts and hex screws rather than the original fastening method. Print in PETG or a higher-temperature engineering polymer, confirm the panel variant and VIN, and verify secure retention and clearance before driving.

Fits X3 · F25 · X4 · F26

Clip-on cargo hook for the rear load-area rail, physically shown installed and documented by the creator as used reliably for more than a year. The creator directly lists X3 E83, 3 Series E46, X5 E53 and 5 Series E39 compatibility, so all four live generations are linked. This is an accessory rather than a reproduction of a BMW service part. Print in PETG as documented, observe sensible load limits, and confirm it cannot obstruct the rear seat or cargo cover.

Fits 3 Series · E46 · 5 Series · E39 · X3 · E83 +1

Replacement retaining ring for a loose center-console cigarette-lighter socket, supplied with multiple loose, installation and in-use physical views for an X3 E83. BMW catalog socket-mount and illuminated-ring numbers vary by location and production date, and the source does not identify which original child component this geometry reproduces, so no number is assigned. Use a heat-resistant material and verify electrical isolation, secure socket retention and plug clearance before use.

Fits X3 · E83

Left and center replacement tabs for the movable dashboard air vents, modeled from the creator's 2007 X3 E83 and physically shown beside original vent tabs. The small movable tabs are not separately serviced by BMW; complete fresh-air grille numbers vary by position and production date, so no parent assembly number is assigned. Print in a cabin-heat-resistant material and verify smooth louver movement without rattle or binding.

Fits X3 · E83

Two-piece bolted replacement for missing metal staples that retain the lower-windscreen rain tray, with loose and installed physical evidence. The source's 51713401811 identifies the complete E83 windscreen-panel cover, while the printed geometry replaces its mounting feature, so that parent number is not assigned. Use a weather- and heat-resistant material, corrosion-resistant M5 hardware, and verify wiper clearance, water drainage and retention after installation.

Fits X3 · E83

Slide-on repair for a broken latch on the low-beam rear headlight dust cover, directly modeled and fit-tested by the creator for X3 E83 headlights. Molded marking 1305239123 is not an 11-digit BMW number; catalog number 63128381326 identifies the complete dust cover, not this printed latch repair, so it is deliberately withheld. Print in PETG or a higher-temperature engineering polymer and verify the cover remains sealed and removable after heat cycling.

Fits X3 · E83

Replacement plus/minus volume rocker modeled after the creator's broken multifunction steering-wheel button and physically shown loose and installed. The creator documents direct fitment to X3 E83 and X5 E53. BMW services the surrounding switch assembly rather than this printed child button separately, so no parent assembly number is assigned. Use a durable heat-resistant material, preserve free button travel, and verify all steering-wheel controls operate without sticking before driving.

Fits X3 · E83 · X5 · E53

Replacement cover for a luggage-compartment child-restraint anchor, physically shown installed by the creator in a 2010 X3 E83. BMW catalogs identify the anthracite/black cover as 51473405879, item 12 with three per vehicle; grey 51473418987 and sand-beige 51473418986 are distinct trim variants and are not assigned. Confirm the interior color and VIN, and verify the cover clips securely without obstructing access to the restraint anchor.

Fits X3 · E83

Six-coin organizer sized for the front ashtray insert and physically tested by the creator in an X3 E83. It also retains the plastic cap from the rear lighter socket. This is an aftermarket accessory, so no BMW ashtray or console parent number is assigned. Use a cabin-heat-resistant material, confirm the insert is bonded securely as documented, and verify it does not obstruct the lighter socket or ashtray closure.

Fits X3 · E83

Two-piece storage mount for the portable Flexible Fast Charger documented with the first-generation iX3: a wall plate retained by three 4.5 mm screw holes and a case-side bracket retained by two M4 x 12 fasteners. The creator printed and physically installed the set, and supplies separate watertight STL files. Verify the pictured charger housing and mounting-hole dimensions before printing because portable charger hardware varies by market and revision. Print vertically with four perimeters as documented, use PETG or another durable heat-resistant material, anchor into a suitable wall substrate, and confirm the charger and cable cannot fall, overheat, abrade, or strain electrical connections.

Fits iX3 · G08

Center-console phone mount sized for an ESR Mini Qi2 charger, with a 58.9 mm diameter and 7.5 mm deep puck recess. The creator documents the printed mount installed in the vehicle and supplies both printable STL and editable STEP files. Verify the pictured console, exact charger revision and phone/case clearance before printing; use a heat-resistant material and ensure the charger, cable and phone cannot obstruct the vehicle controls or overheat.

Fits iX · I20

MagSafe phone mount with a lower cable-management cavity and retaining pegs, designed to fit the factory center-console phone tray. The creator printed it in PETG and documents both the installed fit and the loose physical part with its cable routed in the cavity. Verify the pictured console, charging puck and cable dimensions before printing; use PETG or another heat-resistant material and confirm the cable and phone cannot foul the vehicle controls.

Fits iX · I20