Every printable part.

Angled MagSafe phone mount that press-fits into the factory center-console phone tray and turns the phone toward the driver. The creator's source image shows the printed part installed with a phone attached. Verify the pictured console, viewing angle, MagSafe puck and phone/case dimensions before printing; use a heat-resistant material and ensure the phone remains secure without obstructing the controller, selector, buttons or driving visibility.

Fits iX · I20

Center-console holder for a Samsung Galaxy Fold that locks into the factory phone-tray opening to resist tipping under acceleration. The creator's source image shows the printed holder installed in the vehicle with the phone open and in use. Verify the pictured console and your phone/case dimensions before printing; use a heat-resistant material and confirm that the holder cannot interfere with the controller, selector, buttons or safe driving visibility.

Fits iX · I20

Press-fit MagSafe phone mount for the factory center-console phone tray. The original creator designed, printed and installed it in an iX, and documents the installed fit with an iPhone 13 Pro Max in an Apple case. The main mount may be used alone for a wide cased phone or with the supplied left and right side guides. Verify the pictured console tray and MagSafe puck dimensions before printing; use a heat-resistant material, preserve access to all controls, and confirm the phone remains secure without obstructing driving controls.

Fits iX · I20

Replacement width-adjustment clip that lets larger modern phones, including phones in protective cases, fit the factory snap-in wireless charger. The creator designed, printed and installed it in a 2019 Roadster and documents removal, installation and the completed fit. Compatibility is limited to cars equipped with the pictured snap-in charger; verify the installed charger and clearances before printing. Use a heat-resistant material, print at the documented 45-degree orientation, and do not allow the phone or charger to obstruct controls or overheat.

Fits i8 · I12 / I15

Dashboard adapter that clips beneath the center-vent trim and provides two slots for attaching an accessory holder that would otherwise clamp directly to a vent grille. The creator shows the printed adapter installed by itself and carrying a physical magnetic phone holder, and notes that optional automotive-grade double-sided tape improves retention. This is a removable accessory rather than an original BMW component, so no OEM number is assigned. Use cabin-heat-resistant material, protect the adjacent trim, verify secure attachment and confirm that the holder, cable and device do not obstruct controls, displays, airflow or the driver's view.

Fits i5 · G60 / G61

Center-armrest organizer with a 15 mm vertical phone slot, a 7 mm cable passage, separate cable storage, a general compartment, and a small raised area for keys. The creator shows the physical organizer installed loaded and empty and explicitly identifies compatibility with G22, G23, G26, and i4 interiors. Use ASA, ABS, or another cabin-heat-resistant material as recommended; verify stable seating, phone and cable clearance, and unobstructed armrest movement.

Fits 4 Series · G22 / G23 / G26 / G82 / G83 · i4 · G26

Flexible protective case for the vehicle remote key, with open access to all buttons and the key-ring eye. The creator shows the TPU case fitted to the physical key from both sides and provides useful CAD views of the openings. Print in TPU as specified, confirm every control moves freely and the emergency-key release remains accessible, and verify that the case cannot press buttons unintentionally.

Fits i4 · G26

Two-piece organizer tray for the storage compartment beneath the center armrest, with an optional flexible floor insert and an opening that preserves access to the USB-C port. The creator designed it on a 2023 eDrive40 and shows the physical tray installed empty, with a charging cable, and loose outside the vehicle. Use PETG, ASA, or another cabin-heat-resistant material for the tray and TPU for the optional insert; verify stable seating, cable clearance, and unobstructed armrest movement.

Fits i4 · G26

Large center-console storage bin that replaces the original cupholder after the cupholder and its USB and 12 V connections are removed. The creator scanned the exposed recess, shows the printed bin installed, and includes a separate flexible floor liner. This is a deliberate accessory conversion, not an equivalent reproduction of the powered cupholder assembly, so no cupholder or console parent number is assigned. Use cabin-heat-resistant rigid material for the bin and TPU for the optional liner; disconnect and secure the original electrical connectors safely, preserve the mounting screws, and verify stable installation and full console-cover clearance.

Fits i4 · G26

Forty-millimeter funnel shaped for the windshield-washer filler opening. The creator shows the physical funnel seated in the fill neck from two angles and designed it to print support-free with the larger end upward. This is a service accessory rather than the reservoir, filler neck, or cap, so no parent component number is assigned. Confirm the neck fit before pouring and keep debris and incompatible fluids out of the washer system.

Fits i4 · G26

Cup-position insert shaped for a Hörmann garage-door remote. The creator shows the remote seated in the printed insert in the center console and provides an improved version 1.0 with a deeper pocket and reduced five-degree angle; only that revised model is retained. This is device-specific accessory geometry rather than an original BMW component. Use a cabin-heat-resistant material, confirm the remote and insert remain secure, and verify that neither interferes with the cup positions, console cover, controls, or driving.

Fits i4 · G26

Pair of compact brackets for hanging a JBL BassPro Nano under the rear-seat frame where the optional amplifier is not installed. The creator printed two in PETG at 50% infill, fastened them with the subwoofer's original screws, and shows the installed unit and bracket locations. Confirm the vehicle lacks the conflicting amplifier, protect wiring, use thread-safe fasteners, and verify seat movement, ventilation and secure retention before driving.

Fits i3 · I01

Anti-tip adapter for the source-linked small espresso cup, shaped for the center-console cup position. The creator shows the physical adapter seated in the vehicle and with the matching cup. Print in PETG, ABS or another cabin-heat-resistant material, verify both the cup and console fit, and keep hot liquids securely contained and clear of controls while the vehicle is moving.

Fits i3 · I01

Tool set for I01 outer-door-panel hardware: a deep and standard adjustment-element wrench plus seven clip-saver sizes for printer-tolerance matching. The creator shows the physical tools on the relevant clip and explains that the saver may recover clips that survive warm-weather panel removal. Numbers 51007355279 and 51007378101 identify the serviced clip and adjustment element, not these printed tools, so neither is assigned. Do not reuse cracked or distorted one-time clips; verify panel alignment and secure retention after service.

Fits i3 · I01

Three-piece key-fob box with a separate insert, bottom and lid, designed to prevent accidental button presses while carried in a pocket. The source shows the complete physical case closed, open and holding the I01 key fob. This is a protective accessory rather than the key housing itself. Check that the fob fits without continuously loading any button and that the lid remains secure during normal carrying.

Fits i3 · I01

Deep storage tray that replaces the obsolete phone snap-in adapter in the center armrest while retaining the existing mounting cavity. The creator designed the tray for support-free printing, recommends PETG or ABS/ASA with at least 30% infill, and shows it fitted empty and loaded as well as beside the removed adapter. No snap-in adapter or armrest parent number is assigned. Verify flush seating, secure retention and full armrest movement.

Fits i3 · I01

Organizer for multiple EV charging cards that plugs into a center-console cup-holder slot. The source shows the physical organizer installed and loaded with cards. This is an accessory rather than a serviced console component. Use PETG, ABS or another cabin-heat-resistant material, confirm a secure cup-slot fit, and keep the cards and organizer clear of adjacent controls and loose-object hazards.

Fits i3 · I01

Removable center-console cover with an integrated opening for an Apple MagSafe puck, remixed from the original storage cover. The source shows the physical cover installed and provides model views of the puck opening and underside support. It fits non-braided-cable pucks directly; braided-cable versions may require a small amount of adhesive. Use cabin-heat-resistant material, secure the puck and cable, and verify charging temperature and clearance.

Fits i3 · I01

Four-piece adjustable rear-hatch stop with a flexible buffer, modeled and trial-fitted on a 2020 120Ah vehicle to eliminate play and rattling at the closed hatch. It recreates the function of BMW adjustment element 51247361955, originally used on earlier cars, for later LCI vehicles whose lock-integrated rubber has worn. Print two assemblies as the creator specifies, use TPU for the buffer and heat-resistant rigid material for the body, screw and nut, then adjust symmetrically without preloading or misaligning the hatch.

Fits i3 · I01

Organizer for the small storage compartment below the armrest, with a rigid body, two optional flexible pads and a single-piece multimaterial variant. The source shows the physical pieces and the organizer installed both loaded and empty. Print the body in PETG or another cabin-heat-resistant rigid material and the pads in TPU; verify stable seating and unobstructed access to the adjacent 12 V and USB connections.

Fits i3 · I01

Eccentric 48 mm funnel shaped to clear the surrounding structure at the windshield-washer reservoir opening. The creator shows the physical funnel seated in the fill neck from two angles and designed it to print support-free. This is a service accessory rather than the reservoir, filler neck or cap, so no parent number is assigned. Confirm the neck fit before pouring and keep debris and incompatible fluids out of the washer system.

Fits i3 · I01

Center-console switch faceplate with an added opening for a retrofitted Dynamic Traction Control button from an i8. The source shows the ASA print installed around the complete switch bank and notes reinforced side clips. This is retrofit trim, not a stock I01 faceplate, so no switch-bank or i8 parent number is assigned. Confirm the retrofit wiring separately, use cabin-heat-resistant material, and verify button travel and clip engagement.

Fits i3 · I01

Flexible replacement tether joining the AC and DC fast-charge port caps to the inside of the charge door on CCS-equipped vehicles. The creator shows the printed strap installed on both caps and compares it with the original tether. Print in a durable UV- and weather-resistant flexible material, confirm that all ends seat fully, and check that the strap cannot foul the inlet, caps, hinge or door seal.

Fits i3 · I01

Hatch-mounted warning-triangle bracket with longer screw holes and a hinged retaining flap. The files include a print-in-place combined version and separate bracket/flap parts for snap assembly. The creator shows the printed hinge components and the complete bracket installed in the original hatch mounting points. Use a cabin-heat-resistant material and verify hinge movement, screw engagement, triangle retention and hatch-panel clearance.

Fits i3 · I01