Every printable part.

Three-piece phone holder comprising a display clamp, articulated arm and phone clamp. The source shows the printed assembly installed on the central display from inside and outside the vehicle. Use cabin-heat-resistant material and protective contact pads, avoid excessive clamp force on the display housing, keep the device clear of sight lines and airbags, and verify secure retention before driving.

Fits i3 · I01

Replacement clip for attaching a tether or cord to the parcel shelf. The creator shows the clip installed on the shelf and recommends a shoelace-style cord as an easier-to-release substitute. The source mentions BMW number 51466967605 only for the separate rubber shelf buffer, not this clip, so that number is not assigned. Print upright with a brim as recommended and verify tether retention and hatch/shelf clearance.

Fits i3 · I01

Cup-position adapter for carrying large 32 oz and 40 oz water bottles. The creator shows the physical print installed with a large bottle from several cabin angles. Print with strong walls and suitable infill in a cabin-heat-resistant material, then verify that the bottle is stable, does not obstruct the iDrive controller or adjacent cup positions, and cannot tip during vehicle movement.

Fits i3 · I01

Replacement latch for the center armrest. The source provides installed views of the printed latch holding and releasing the armrest, plus a model view. No original child-component number is stated or independently established, so no surrounding armrest or console assembly number is assigned. Use cabin-heat-resistant material and verify smooth release, positive engagement and full armrest travel before regular use.

Fits i3 · I01

Two-piece auxiliary cup holder that prints as a base and upper ring and snaps together. The creator shows physical ABS and nylon prints, including installed use with narrow and large bottles. The OBJ and matching 3MF are retained. Use a cabin-heat-resistant material, inspect the snap joint for complete engagement, and confirm stable seating and beverage clearance before driving.

Fits i3 · I01

Two-piece center-console mount with the standard AMPS four-hole pattern for compatible phone or tablet cradles. The creator split the long arm for a 150 mm print bed and shows it installed with a device cradle without blocking the climate vents. Bond the two printed sections with a suitable structural adhesive, use a cabin-heat-resistant material, and verify the AMPS fasteners, bonded joint and cup-position fit before driving.

Fits i3 · I01

Insert for the fixed front cup position that supports a 330 ml can in a 59 mm opening and provides a 74 mm-wide phone slot when no drink is present. Three bore variants are included: nominal, +1 mm and +2 mm for coatings or fit adjustment. The source shows the nominal design installed beside a can. Use cabin-heat-resistant material, test the bore and seating before use, and keep the phone and drink clear of adjacent controls.

Fits i3 · I01

Curved organizer for UK 10p, 20p, 50p and £1 parking coins, with an optional separate lid. It mounts beneath the center armrest using double-sided foam tape; the source shows both the loaded organizer and the lid installed. This is UK-currency-specific accessory geometry rather than an original serviced component. Use automotive-grade tape and cabin-heat-resistant material, and confirm the organizer remains secure and does not obstruct the armrest mechanism.

Fits i3 · I01

Cup-position mounting arm for a reusable magnetic phone head, with an integrated cable comb and cable pass-throughs. The creator physically printed the arm, adapted the threaded base and magnetic head from a generic mount, and shows the complete assembly installed in the center-console cup position. Use a cabin-heat-resistant material, confirm the threaded adapter and ball joint are secure, route cables clear of the controls, and verify that the device cannot interfere with driving.

Fits i3 · I01

Open-sided wrench for removing and installing the plastic retaining nut around the hazard switch without plier damage. The creator physically demonstrates the wrench with the switch and recommends the stiffest suitable material because the clearance slot permits some flex. The title's 61311356193 identifies an early complete hazard switch, not the printed tool or its nut, so it is not assigned as an OEM number. Switch design varies by production date; use only light hand torque on the plastic nut and confirm jaw fit before turning.

Fits 02 Series · Type 114 / E10

Redesigned flexible lower steering-column pad for later cars, physically shown installed using the original mounting points. The creator states that steering-column design changed during production and does not claim early-car fitment; compare the mounting points and column profile before printing. Print slowly in durable TPU with strong bed adhesion. Because this is deliberately not a duplicate of the original lower trim panel, catalog number 32311110912 is documented only as the corresponding late original panel and is not assigned to this custom part.

Fits 02 Series · Type 114 / E10

Two-piece decorative trim bezel for a period Blaupunkt Frankfurt radio, physically shown installed. The outer tray can be printed in a metallic-look material and the center in PETG, ASA or another stiff cabin-heat-resistant material; bond the two pieces and retain them beneath the radio knob washers as documented. The source notes that factory faceplate fitment varied with equipment, so verify radio shaft spacing, console type and Behr air-conditioning-console clearance. This is custom trim and receives no radio or console parent number.

Fits 02 Series · Type 114 / E10

Replacement automatic-selector gear-indicator bezel, shown physically installed and loose for inspection. The creator specifies a filament color change: print the first layers in transparent material and the following layers in black so the markings remain legible. Automatic-transmission fitment only; compare the selector opening and indicator layout before installation. No parent selector-assembly number is assigned.

Fits 02 Series · Type 114 / E10

Workshop gauge for checking the center-to-center distance between the front strut towers on early 1966-1967 02-series bodies. The creator physically demonstrates the tool and cites a target of 996 ± 1 mm, measured from the indicated prism edge. This is a diagnostic aid, not a structural repair fixture or substitute for the BMW body-repair manual. Verify the specification against documentation for the exact body before acting on a reading; no vehicle component OEM number is applicable.

Fits 02 Series · Type 114 / E10

Four-piece replacement shift surround for the long center console, shown physically assembled and installed. It works with the original console components and the creator's triple-gauge/radio panel. The sections require test-fitting, bonding, filling, sanding and a suitable textured finish; use cabin-heat-resistant material, number 8 speed nuts and corresponding screws as documented by the creator. The printed surround is not the complete console assembly, so no parent assembly number is assigned.

Fits 02 Series · Type 114 / E10

Two-piece custom console panel for three 52 mm gauges and a period-size Blaupunkt radio. The creator printed, finished and installed the panel and documents use of the original ashtray and hazard-switch assembly plus a separate rear radio support. Print in ABS or another cabin-heat-resistant material with robust shells, test-fit both halves, sand before bonding, and support the radio at the rear so vibration cannot crack the surround. This is a custom panel, not a separately catalogued original component, so no console or dashboard parent number is assigned.

Fits 02 Series · Type 114 / E10

Shroud for the dashboard clock used in 2002 tii applications. The preserved gallery shows loose physical clock-and-shroud assemblies as well as the model render. This is an accessory around the clock rather than the complete clock or dashboard assembly, so no parent OEM number is assigned. Use cabin-heat-resistant material and compare the clock opening, depth and dashboard clearance before final installation.

Fits 02 Series · Type 114 / E10

Replacement bushing modeled from the original linkage part on a 1974 US-market 2002 and physically printed and used by the creator. The supplied geometry is 26 mm outside diameter, 12.5 mm bore and 16 mm hat diameter. The original is rubber; use a suitable flexible material for original-like compliance, or note that a rigid ABS print deliberately produces firmer shift feel. The catalog contains several production-date-dependent linkage bushes and joints, and the source does not identify which serviced child number it reproduces, so no OEM number is assigned. Confirm dimensions, linkage articulation and secure retention before driving.

Fits 02 Series · Type 114 / E10

Two-piece smartphone mount for the iX1 U11 cockpit, with a separate ball head and tight-fit, loose-fit, or loose-fit-with-hex-nut base variants. The creator shows the printed assembly installed beside the curved display and explains that the tight version requires substantial installation force, while the loose versions require EVA foam tape and otherwise may not support the phone. This is accessory geometry rather than a serviced BMW component, so no display, trim or dashboard parent number is assigned. Use cabin-heat-resistant material, avoid excessive force on trim, keep the phone clear of sight lines and airbags, and verify secure retention before driving.

Fits X1 · U11

Four one-piece tray variants for fitting one or two Baseus Simple Mini3 15 W wireless chargers in the 2023 X1 center-console shelf: full and short versions for either a single charger or a pair. The creator dimensioned the tray to the vehicle, physically printed it in PETG and 85A TPU, shows installed trays with phones, and reports testing with multiple iPhone 6.1-inch and Galaxy S models. Chargers insert from below and their cables route to the right-side USB-C ports. This is aftermarket accessory geometry, so no console or charging-module parent number is assigned. Do not use PLA; confirm cable strain relief, charging temperature, phone retention and unobstructed controls before driving.

Fits X1 · U11

Removable insert for the center-console cup position that keeps 330 ml and 500 ml cans stable. The creator designed and physically tested version 7 in an iX1 U11, shows it installed with a can, and notes that the sloped base must be rotated until it seats correctly. The STL and matching 3MF are retained. This is an accessory rather than a separately serviced BMW component, so no cup-holder or console parent number is assigned. Print in ASA, ABS, PETG or another cabin-temperature-resistant material rather than PLA; verify stable seating and clear access to adjacent controls before driving.

Fits X1 · U11

Removable insert for the BMW X1 F48 center-console cup holder, with separate slots for the vehicle key and a small remote. The creator identifies the F48 application and physically printed and demonstrated the insert holding both devices. This is an accessory rather than a reproduction of a separately serviced BMW component, so no cup-holder or console parent number is assigned. Use PETG, ABS, ASA or nylon rather than PLA because parked-cabin heat can deform low-temperature material; confirm the insert seats securely and does not obstruct adjacent controls or the second cup position.

Fits X1 · F48

Replacement black trim cover for a broken rear-seat ISOFIX anchor opening, physically shown installed by the creator on a 2012 BMW X1 E84. BMW E84 rear-seat catalogs identify the black separately serviced cover as 52207118674, item 9 with four per vehicle; Hubauer documents supersession to 52207332435. Beige 52207152210 and oyster 52202993792 are distinct color variants and are not assigned. Match black trim and verify the cover clips securely without obstructing access to the child-seat anchor.

Fits X1 · E84

Two replacement retainer geometries for repairing broken attachment tabs on the BMW X1 E84 engine air-filter housing. The creator links the original repair write-up and supplies physical comparisons, loose parts and installed engine-bay views for both shapes. The printed pieces repair features of the larger air-filter housing rather than reproducing a separately serviced BMW child component, so no housing parent number is assigned. Print in PETG as documented or a higher-temperature engineering polymer, fasten exactly as shown, and verify intake sealing, bonnet clearance and retention after heat cycling.

Fits X1 · E84