Every printable part.

Coin organizer sized for the removable cup-holder opening in the BMW X1 E84 center console. The creator physically shows the print loose, fitted with euro coins, installed beside the parking brake and concealed beneath the armrest. This is an accessory rather than a reproduction of a BMW service component, so no parent cup-holder or console number is assigned. Use PETG, ABS or nylon rather than PLA because parked-cabin heat can deform low-temperature material, and verify the insert cannot interfere with the handbrake or armrest.

Fits X1 · E84

Adapter for fitting a Dayton Audio RS75-4 midrange driver to the front-door and rear-deck speaker enclosures of BMW E31 840 and 850 models. The creator supplies STL, 3MF and Fusion 360 source geometry and physically demonstrates the adapter loose and fitted in the factory enclosures; mounting holes require drilling after printing. This adapts aftermarket hardware rather than reproducing a BMW component, so no speaker-box parent number is assigned. Verify cone, grille, wiring and fastener clearance before reassembly.

Fits 8 Series · E31

Right-hand-drive console cover for fitting an E60 M5 SMG selector in a BMW E31 8 Series, physically shown installed by the creator and printed in PETG at 50 percent infill. This is custom retrofit geometry rather than an original E31 service component, so no parent console, selector or trim number is assigned. It applies only to RHD cars with this specific conversion; confirm selector travel, wiring clearance and secure console retention before driving.

Fits 8 Series · E31

Thickened replacement cover for the BMW E31 heater/water-valve assembly, physically printed by the creator and reported to resist under-bonnet heat. The design uses 10 x 2 mm neodymium magnets against the valve fasteners. BMW catalogs identify the original separately serviced cover as 64111383499 for E31 840i/840Ci, 850i/850Ci and 850CSi; genuine production ended in 2015 with no documented supersession. Use high-temperature material, secure the magnets, and confirm hose, wiring and bonnet clearance after installation.

Fits 8 Series · E31

Four-print set of replacement fulcrum sleeves for the BMW E31 pop-up headlamp bucket, physically shown loose and installed at the upper bucket attachment by the creator after replacing warped original inserts. BMW catalogs identify the separately serviced joint sleeve as 63121392066, position 13 in the headlamp component diagram and six per vehicle. Print in heat-resistant material, replace all damaged sleeves, then verify bucket retention and have headlamp aim checked before night driving.

Fits 8 Series · E31

Replacement plastic pivot base for a BMW E31 sun visor, supplied for the left/right location and physically shown both loose and installed by the creator on an 850i. The original metal visor shaft is reused and its diameter can vary; drill the centre only as needed for a careful fit. BMW services the surrounding colour-specific electrical-contact bracket as a complete assembly, so those parent/contact-bracket numbers are not assigned to this printed repair body. Match anthracite, silver-grey, parchment or Individual trim and verify mirror-light contact operation before use.

Fits 8 Series · E31

Four-part left/right repair-clip set for broken retaining features on BMW E38 interior decorative trim strips. The creator physically demonstrates both clip styles against the back of the trim and advises removing the failed feature, test-fitting, and bonding the replacement; the smaller style was designed for the front strips and may need additional adhesive clearance on rear strips. These are repair geometries rather than separately cataloged BMW components, so no parent trim-strip number is assigned. Use cabin-heat-resistant material and compatible adhesive, then verify full retention and clearance before refitting.

Fits 7 Series · E38

Left and right body-side angle covers for the adjustable/split rear-seat configuration of the BMW E32, physically shown loose and installed by the creator. The paired files reproduce the cataloged left/right covers in black, crimson, silver gray, light silver gray, ultramarine and parchment variants; exact color must be selected or finished to match the vehicle. Installation uses expanding rivet 61131382239, but that separate fastener is not assigned as an OEM number for the printed covers.

Fits 7 Series · E32

Replacement adhesive-backed mounting tab for an E32 center-console ashtray after the original molded console tabs break. The creator documented the repair on a November 1990 730i: print two tabs, transfer the original clip nuts, bond the tabs inside the console and reinstall the ashtray. This is repair geometry rather than a cataloged BMW component, so no parent ashtray or console number is assigned. Confirm adhesive compatibility and full ashtray clearance before refitting the HVAC panel.

Fits 7 Series · E32

Replacement windshield support/adjuster for the BMW E32, shown physically installed by the creator while fitting glass. BMW catalogs identify the exact original component as support 51311948155, produced from June 1986 across E32 730i/730iL, 735i/735iL, 740i/740iL and 750i/750iL applications in LHD and RHD markets. Compare the body channel and original support before use, and leave final glass positioning and bonding to a qualified installer.

Fits 7 Series · E32

Custom front towing-eye opening cover designed and physically installed by the creator on a BMW G32 6 Series Gran Turismo with the pre-LCI M Sport front bumper. The round face intentionally differs from the curved factory-painted flap and includes a removal notch and decorative BMW relief. Use only on the matching pre-LCI M Aerodynamics (S715A) bumper opening, print in a weather- and heat-resistant material, paint or seal for UV exposure, and verify all retention tabs before road use. Genuine BMW reference 51118072209 identifies the original primed M-bumper tow-eye cover; it is not a claim that this custom round face is factory geometry.

Fits 6 Series · G32 Gran Turismo

Dual catch-can mounting bracket designed by the creator for the S63TU engine bay in the BMW F13 M6 and F10 M5. The creator links an installation video for the twin-turbo M6 setup, providing physical-use evidence beyond the preserved CAD render. Print in a heat-resistant engineering material such as nylon, keep clear of hot or moving components and hoses, and inspect retention after initial heat cycles. This is an aftermarket accessory with no original BMW component counterpart, so no OEM number is assigned.

Fits 5 Series · F07 / F10 / F11 / F18 · 6 Series · F06 / F12 / F13

Service wrench for the notched BMW fuel-tank screw cap used on E46, E60/E61, E63/E64, E65–E68, E83 and E53 vehicles. The creator tested the same interface on an R53 MINI and identified BMW screw cap 16116762417; BMW catalog cross-reference independently confirms that cap across the listed BMW chassis. The printed wrench is not the screw cap itself, so no OEM number is assigned. Use a stiff engineering polymer, hand tools only, and replace rather than reuse any visibly damaged print.

Fits 3 Series · E46 · 5 Series · E60 / E61 · 6 Series · E63 / E64 +3

Replacement clamp for the factory BMW E24 headlamp cleaning system. BMW catalogs identify the left/right clamp pair as 61661362211 and 61661362212 across European E24 628CSi, 630CS, 633CSi, 635CSi and M635CSi applications; 61661362211 is discontinued while 61661362212 remains cataloged without a supersession shown. Use only on cars equipped with the headlamp cleaning system, confirm side and production configuration by VIN, and test the wiper path before operation.

Fits 6 Series · E24

Two repair-stop geometries, 15.5 mm and 22 mm, for damaged stops on the chrome headlamp glass-holding frames of BMW E24 cars. BMW 63121361709 and 63121361710 identify the complete left and right glass-holding frames, not these printed repair inserts, so neither parent number is assigned. Select the matching size, use a weather- and heat-resistant material and confirm full wiper travel without lens or trim contact.

Fits 6 Series · E24

Replacement passenger-door lock cam/linkage for the BMW E24, reproduced to repair the broken plastic element formerly supplied only inside BMW lock repair kit 51219061345. The printed geometry is not the complete kit, so that parent number is intentionally not assigned. Compare side and linkage geometry, use a tough engineering polymer and fully test manual and central locking before closing the door.

Fits 6 Series · E24

Driver- and passenger-side snap-fit clips that couple the exterior door lock to the central-locking microswitch on BMW E23 and E24 cars. The source shows the clip installed in an E24 door and supplies side-specific geometry. Use a tough, heat-tolerant material, warm only as needed for assembly, and verify that lock, unlock, key return and microswitch operation are smooth before closing the door.

Fits 6 Series · E24 · 7 Series · E23

Replacement perforated front-speaker cover for the BMW E24 interior. The preserved source provides exact E24 fitment and printable geometry, but only a rendered source image survives; compare the opening, fastener points, color and grain against the original cover before installation. Use a cabin-heat-resistant material and deburr every perforation.

Fits 6 Series · E24

Washer-fluid filling funnel for BMW G30 and G31 models and potentially other 5 Series or 7 Series vehicles using the same filler neck. The documented source gallery shows the funnel installed in a G30/G31 filler neck, so only those directly verified generations are linked here. Print in PETG with a 0.4 mm nozzle. Keep the funnel clean, remove it after filling, reinstall the original cap fully, and wipe away spills before driving.

Fits 5 Series · G30 / G31 / G38 / F90

3 pin tool for rewinding rear BMW brakes. I designed the tool to work with a G30, but I think it will work with other BMWs models. The tool is reversable and allows you to either use the triangular pattern for best fit, or the head of the screws. Note: Do not attempt to use without screws installed, it will just shear off the triangular pieces. The design uses #8 x 32 x 1/2" allen head cap screws. For printer settings, beef up the perimeter to 8 and use 50% triangle infill for added strength. Basic PLA did the job. I used the tool successfully to complete a brake job, and redesigned it to improve strength and fit. Simply use a 3/8 ratchet and short extension, then turn clockwise and apply downward pressure. Depending on how tight your calipers are you may only get one use from these, but for a DIY job it works without buying any special tools to compress the caliper. This creator-designed three-pin adapter was successfully used on a G30 rear brake and then strengthened. Install all three specified #8-32 cap screws before use; use a 3/8-inch ratchet and short extension, turn clockwise with controlled downward pressure, inspect the print continuously, and discard it at the first sign of cracking or deformation. Follow the applicable BMW repair procedure and independently support the vehicle; this printed service aid is not an OEM tool.

Fits 5 Series · G30 / G31 / G38 / F90

This fits a BMW F11 and maybe also other BMW cars from around 2015. If the old cable brakes, this is a replacement of the ring at the cap and the cable. The original ring has to be removed from the fuel cap. Be careful not to brake anything else then the turning ring. Use side cutting pliers or a similar tool. The put the new ring onto the fuel cap. If the ring does not fit you can also adjust the width in the attached model and re-export. I used TPU 95 for the print. Nozzle diameter can be 0.25 - 0.4, all work. I printed with supports but this leaves a rough finish. This also leads to the fact, that the ring does not slide as good as the original one. But overall it works. Don't forget to like if you like. Creator reports the TPU replacement fits and works on an approximately 2015 F11, while noting rough support surfaces can make the ring slide less freely. The editable FreeCAD source is retained for measured adjustment. Do not force the ring or damage the fuel cap. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

This is a replacement part for the BMW 5 Series Touring (F11). It is the sliding clip ("leash" or "dog") located in the D-pillar track that automatically raises and lowers the rear cargo blind (luggage cover) when the trunk is opened. OEM Part Number: 51437232775 Tested on: BMW F11 520d Touring IMPORTANT INSTRUCTIONS 1. FUNCTION: This part slides inside the track of the rear pillar. It is crucial for the automatic retraction of the luggage cover. 2. LEFT vs RIGHT Side: The uploaded file is for the LEFT side. If you need the RIGHT side, simply use the "Mirror" function (along X-axis) in your slicer software. 3. MATERIAL RECOMMENDATION: Because this part moves in a track and bears weight, I strongly recommend printing with NYLON (PA). - Nylon provides the necessary low friction and high durability. - ABS/ASA might work but will wear out faster. - PLA is NOT recommended. 4. PRINT SETTINGS: - Infill: 100% (Solid) for maximum strength. - Orientation: Print in an orientation that maximizes layer adhesion strength for the pulling force. Designed from scratch as a cost-effective alternative to the expensive OEM repair kit. Creator-tested on an F11 520d Touring. The supplied file is the left sliding coupling; mirror on X for the right side. BMWFans identifies genuine BMW 51437232775 as Coupling, left, produced from 2010-06 for F11/F11 LCI European applications including LHD and RHD. Use nylon where possible, not PLA, and verify smooth movement before loading the blind. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Since I lost two of my backseats isofix covers, I redraw them. Maybe someone else need them as well. I printed them with a 0,2mm nozzle, fuzzy skin at the frontside (strenght 0,04mm / distance 0,1mm), and forced support for the first layers…. The creator measured lost F10/F11 rear-seat covers and provides physical comparisons with the original. This is a cosmetic access cover only; confirm the ISOFIX anchorage remains fully accessible and unmodified. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

This is a usb adapter designed to replace the cigarette lighter in a BMW F07 car. If you have a android head unit it will fit perfectly with the usb port provided. You'll have to remove the central console to have your cable passing through and remove the existing cigarette lighter. A simple rilsan belt will keep it in place. I printed it textured to avoid finger marks. It is very convenient to plug my controller and play games during lunchtime :-) or just plug any thumbstick Designed and used in an F07 with an aftermarket Android head unit. The two source variants share the same envelope but differ internally. Installation requires console removal and replaces the existing 12-volt socket; disconnect power and verify connector retention and insulation. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18