Every printable part.

Replaces metal ashtray in 5 series BMW with a more useful box. Both creator-supplied depth variants are retained. Physical photographs show the insert installed in the F10 console; keep the sliding lid and nearby controls unobstructed. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

Just glue the pin to the plate and add some velcro and you are done! The creator tags F10/F11 and supplies physical photographs of the printed two-piece lock. Glue the pin to the plate, add adhesive hook-and-loop material, and confirm the mat cannot interfere with pedal travel. Verify dimensions against the original component and confirm full operation before regular use.

Fits 5 Series · F07 / F10 / F11 / F18

It works and fits, but it is sturdier than the original and if you want extra sturdiness, then make it even thicker, because there is still more place for that part. Print the pin as a separate part and glue it together. it will look better, save you time and work better. Please do not re-upload STL or any other mesh version of this project. I upload STEP only, because I want it to be easily editable. Do not poison the internet. For commercial use contact me and I am sure that we can build something cool out of it. Other than that do whatever you like as long as you mention me as the author of the model. Creator reports the replacement fits and works, and supplies separate claw/pin and combined STEP versions. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Storage-tray set for the center-console recess in BMW E60 and E61 models. Variants include a blank tray for customization, the creator’s everyday layout, a three-coin layout, and a tray for a Hörmann HS M 2/4 garage-door remote with an additional small compartment. The creator reports that the tray fits the existing console recess well. The demonstrated print used Fiberlogy Impact PLA; PETG is also suitable, while ordinary PLA is not recommended for vehicle-cabin temperatures. Verify dimensions, secure retention, and unobstructed operation.

Fits 5 Series · E60 / E61

Tool-free front cup holder for BMW E60 and E61 models without the factory front cup holders. It avoids replacing or modifying the dashboard and is compatible with manual-transmission cars. The creator developed four prototypes over three weeks. The model is configured with three perimeters and three top and bottom layers and is sized for 500 ml cans. The test piece was printed in PLA, so do not place hot drinks in it. Taller occupants should check knee clearance because contact can push the storage compartment inward. Verify fit, secure retention, and unobstructed operation before driving.

Fits 5 Series · E60 / E61

My Driver side tab cracked in half. It would be a party when on the highway/ move excessively on bumps. Mirror it for the driver side !! PRINT WITH SUPPORTS !! There's a hidden pocket in the tab, you wont see the supports but it will make it print. Creator installed the repair after a cracked driver-side tab caused lamp movement; mirror the right-side geometry for the opposite side and verify beam aim after installation. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Hey Guys, i made this Center Console Compartment for my BMW E61. I made it because i had a Phone Holder in my center console which i never used. So i decided to get it out and print myselfe a Compartment. Now i can store more things in my Center Console. I cuted the thing into two parts so you can print it easy. Just glue it together after you printed it. Creator fitted this storage compartment after removing the unused factory phone holder; both complete and split/glue variants are supplied. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

If you want to keep your ashtray tidy, I recommend this model Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

the bmw e60 vents were very floppy and i went to see what was wrong and some how that small piece in my vent was the whole reason my vents wernt standing straight and working i found one of them so i could design these pieces 1-1 as the original i printed this in bambu black carbon fibre fillament Measured one-to-one from the original clip to restore a loose rear center vent. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Made this for a friend because his original case had a crack. The hole is wider then the stock one because we had to use another aux jack. Feel free to remix it because my version is not perfect. For clipping it in you have to use the original metal clips which fits in the sides of the model. Forgot to make a picture of the 3d Printed model. Designed for a replacement auxiliary jack with a wider opening; reuse the original side metal clips. The creator notes this revision is not cosmetically perfect. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

I edited the clip for E90 made by mrhaze222 so that it would fit in E60 console cover. it should be tight enough to twist it in the hole and strong enough to handle the metal rod,it may get loose a bit if you're planning on taking the cover often so if you want it to hold on longer and be tighter/stronger then you might aswell use the ABS filament but PLA should be enough. It perfectly fits in BMW E60 2003 so it should fit aswell in other models Remixed specifically for the E60 console cover; creator describes the rotational fit and spring-rod retention. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Cable holder for 7mm hole. Printed without brim. Creator documents the printed holder on an E61 door harness and specifies a 7 mm mounting hole. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Attaching the trailer socket bmw e60 / e61 Retain only the socket mounting bracket; verify trailer wiring and legal requirements independently. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

The nasty clips at the back of the headliner which always breaks when removing. Works very well with PETG. For non commercial use only! Creator reports the PETG replacement works very well at the rear of the E61 headliner. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Screw clip for BMW sub-panels. I used it for e60 100% infill (or less is also good) 0.2 layer hight Creator reports using this 30 mm screw clip on an E60 under-panel. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

The center console catch broke in my BMW E61. I've removed the remaining plastic and printed this piece. Attach with two screws and it works perfectly again. Print with 100% infill for extra strength. Creator reports a perfect working repair attached with two screws; photographs show the installed E61 console lid. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Just a replacement for the original Dummy. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

EDITED! THIS IS THE ACCURATE MEASUREMENTS. FITS PERFECT! LxBxH 30x15x20mmm Broke some clips when i took down some of my headliner, and could not find any so i made drawn and made some. Clips for headliner in BMW E60 an E61. Creator states the revised dimensions fit perfectly after replacing the earlier version. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Rear wiper gear BWM E60 Creator supplies physical comparison evidence. This rear-wiper part is for the E61 Touring body, not the E60 sedan. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E60 / E61

Replacement for BMW OEM part 51478230749 (Support for Tension Strap). Used to secure the trunk floor panel in BMW E39 E36 models. Printing recommendation: For maximum strength, print the part at a 45° angle using supports. This print orientation improves layer adhesion in the areas subjected to the highest load, resulting in a stronger and more durable part. BMW catalog lists support 51478230749 from 1996-09 and records bilateral interchangeability with superseded 51478197822; retain the creator-listed E36/E39 fitment. Verify dimensions against the original part and confirm full operation before regular use.

Fits 3 Series · E36 · 5 Series · E39

I designed these brackets because the original BMW E39 tweeter mounts are too small to fit the Gladen Alpha 130 G2 tweeters. Installing aftermarket tweeters in the factory location can be challenging, as the available space inside the original E39 mounting brackets is very limited. These adapters allow the Gladen tweeters to be mounted securely while retaining the factory installation position. Compatible Speaker Set Gladen Alpha 130 G2 Original BMW Parts Left side: 65138362527 Right side: 65138362528 OEM reference: Printing Notes Designed for BMW E39 factory tweeter locations. Tested with Gladen Alpha 130 G2 tweeters. PETG or ASA is recommended for improved heat resistance inside the vehicle. Print with at least 3 perimeters and 30–40% infill for good durability. I hope this model helps anyone upgrading the factory audio system in their BMW E39. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

Replaces the integrated plastic tab that commonly shears off, allowing the fog light to be secured without replacing the entire bumper. The bracket replicates the factory slot geometry. Once bonded, the fog light housing slides into the bracket and locks into place using the original mounting hardware/method. Material: Would recommend ASA or ABS. Compatibility: 2001–2004 (Facelift / LCI) BMW E39 5-Series models. Will not fit Pre-Facelift or M-Sport/M5 Bumpers. I also sell the printed parts: Installation Instructions: 1. Access: Gain access to the fog light assembly either by removing the front splash guard in the wheel well or by removing the front bumper entirely. 2. Alignment: Leave the fog light attached to the bumper by its remaining intact mounting point. 3. Test Fit: Position the repair bracket and verify that it makes flush contact with the bumper surface. Ensure the circular tab on the fog light housing slots correctly into the bracket. 4. Preparation: If remnants of the broken original bracket interfere with the fitment, trim them down until the repair bracket sits flush. 5. Bonding: Thoroughly clean the contact areas on both the bracket and the bumper. Apply a strong epox Creator limits fitment to the facelift/LCI bumper. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39

I used: fibre reinforced ABS 20 % infill 4 outer wall thickness 0,4mm nozzle no support but slower outerwall speed Might also work with generic ABS/ASA/PETG BMW catalog identifies screw plug 71111179444 from 1986-06 with broad BMW toolbox usage; the API fitments reproduce the creator-listed E38/E39/E60/E65/E66 families. Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39 · 5 Series · E60 / E61 · 7 Series · E38 +1

BMW E39 523I glovebox nut PETG,ABS or other Verify dimensions against the original part and confirm full operation before regular use.

Fits 5 Series · E39