Every printable part.

Simple cab hook for retaining a loose seat belt when it is not in use. Confirm the mounting position and belt clearance before drilling or attaching it.

Fits Series · 3

Tool-free half-turn thumbwheel fastener for the rear towing-point cover. Print at 100% infill for strength.

Fits Discovery · 3 · Discovery · 4

Land Rover Discovery 3 armrest cap.

Fits Discovery · 3 · Range Rover Sport · L320

Land Rover Discovery 1/2 window switch bezel. You need to print 4 pins

Fits Discovery · 1 · Discovery · 2

Front bumper end cap clip for Defender

Fits Defender · Puma

Clip to hold brake pipes to chassis for Defender TD5. It fits into existing 7mmØ holes in chassis and holds a 5mmØ brake pipe secured by a 4.7mm*1.3mm nylon cable tie. It's designed to be forced into the chassis with a hammer and strongly hold the brake pipe even without beeing secured by the cable tie, but be aware that brake pipes are quite sensible parts of a vehicle and may result to your death if not secured appropriately. Use this part at your own risk and check conditions of the brake pipe clip regularly.

Fits Defender · Td5

Sun Visor Retaining Clip designed for the 1996-2001 Toyota Camry (XV20). Replacement bracket designed and driver-side tested on a 1998 Camry

Fits Camry · 4th Gen

Replacement volume-control knob for the factory rear-seat entertainment system in the second-generation Toyota Sequoia.

Fits Sequoia · 2nd Gen

Two-piece replacement fuse-box cover with raised fuse-position text, modelled from a damaged original cover.

Fits Land Cruiser · 60 Series

Workshop tool for seating the oil seal in an LT230 transfer box. The creator printed it in PETG with a 2 mm shell and 50% infill.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Two fit variants of a blanking plate for the 1998 dashboard ashtray opening.

Fits Defender · 300 Tdi · Defender · Td5

Two-part centre-console organiser comprising a main tray and removable divider. Use a cabin-temperature-resistant material because PLA may soften in summer heat.

Fits Discovery · 3

Workshop fitting tool for seating the rear hub seal squarely.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +3

Four-part clamp mount for attaching a Salora CDC100-style dashcam to the interior mirror. Short and tall ball-arm options are included, together with the mirror clamp and retaining nut.

Fits Freelander · 1

Dashboard drinks holder for the Range Rover P38, based on genuine Land Rover accessory LRN32685 with printability changes and an added tray for pens and coins.

Fits Range Rover · P38

Simplified fixed replica of the original Range Rover Classic dashboard vent grille. The source model is based on a full-size Classic and is intended to be glued in place.

Fits Range Rover · Classic

Replacement fuse-box cover for the full-size Range Rover Classic.

Fits Range Rover · Classic

Trim Clip for Fuse Box Cover on Defender from 2007 Onwards

Fits Defender · Puma

Left and right replacement hinges for the rear parcel shelf. The original source supplies both handed files and a physical comparison image; a later credited remix explicitly identifies this original design as the W177 parcel-shelf hinge and retains the same interface while adding reinforcement. Print the original files on their flat sides at 0.16 mm, with four walls and no supports; the creator suggests fuzzy skin only on the four towers that enter the parcel shelf. A later source specifies PETG for this cabin/cargo application. Inspect layer adhesion and both pivots, confirm free movement, and avoid loading the shelf until both hinges are fully seated. No Mercedes number is assigned: A1776905400 identifies the complete parcel shelf, not either printed hinge child.

Fits A-Class · W177

Clip-on rear-camera mount developed for the estate headliner and a Vantrue N4/N5 RC-01 rear camera. It clamps between the headliner and roof sheet without screws or holes and is shown installed clear of the tailgate. Fitment is limited to the estate body. Protect the headliner, keep the camera and cable clear of airbags, visibility and tailgate travel, and verify the mount cannot detach.

Fits C-Class · W205 / S205 / C205 / A205

52mm hub nut socket for a wide range of Land Rover models. Most wheel bearings only need gentle torque - a few later models use the same nut but with huge torque and this likely won't work for those. 1/2" socket plus a 27mm (wheel nut) sized hex on the back. Designed to be printed without supports. Print in something robust.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Discovery · 1 +5

Replacement ball outlet for a cracked headlight-washer nozzle, shown loose and fitted to the original sprayer. The creator bonded the PLA part with water-resistant adhesive and notes that the bore may need careful finishing. No complete-nozzle parent number is assigned; verify sealing, spray direction, cover clearance and legal washer operation before driving.

Fits Z4 · E85 / E86

Replacement square cover plug for the screw near the door armrest on BMW E65/E66-family door trim. The creator shows both a loose printed/reference comparison and the installed cover in an E65 door, and describes the geometry as an exact OEM-cover copy. The photographed part is the dark-silver trim variant corresponding to BMW 51417025647; verify color, 24 mm square footprint, door position, production date and VIN before printing because black, flannel-grey, beige and other door-trim cap variants also exist. Use cabin-heat-resistant material and test the retaining legs gently before final installation.

Fits 7 Series · E65 / E66 / E67 / E68

Replacement 10 mm square plastic body grommet for number-10 screws used on exterior trim such as side-marker lamps.

Fits 4Runner · 1st Gen