Every printable part.

Replacement push button for the left or right folding rear-seat release on 2010–2018 vehicles.

Fits 4Runner · 5th Gen

Workshop socket for removing and installing the radio-antenna retaining nut.

Fits Land Cruiser · 80 Series · Lexus LX · 450

Loose- and tight-fit holders for fitting a 5 mm 12-volt LED and panel-mount bezel into a 16 mm Jaeger or Smiths gauge opening. The creator notes that the tight version may break during removal and suggests optional hot glue after installing the LED.

Fits Series · 2A · Series · 3

Replacement windscreen-washer reservoir cap with retaining-ring eyelet, spill-reducing internal lips, and a 0.4 mm vent hole.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Printable male connector bodies and mounting parts for the original dashboard E-switch and hazard-switch positions.

Fits Defender · Td5

Replacement flange for repairing or upgrading the Td5 air-filter housing connection.

Fits Defender · Td5

Air-intake vent that replaces the removable seat-box floor grommet when fitting a diesel night heater. The creator secured it with marine sealant.

Fits Defender · 200 Tdi · Defender · 300 Tdi · Defender · Td5 +1

Console for mounting auxiliary switches or other equipment in the small driver-side dashboard recess. Blank and pre-drilled versions are included for both left- and right-hand-drive vehicles

Fits Defender · L663

Base-plate adapter for fitting GMC/Chevrolet pickup tie-down anchors to the cargo-area ceiling. Installation uses two 3/8 × 1.5-inch carriage bolts with washers and nuts.

Fits Defender · L663

Replacement support bracket for the instrument cluster where the original is missing or damaged. Compare handedness, hole spacing, and dashboard structure before printing.

Fits Series · 3

Replacement threaded button for the handbrake lever. The source recommends finishing the undersized bore with an M5 tap for a secure fit.

Fits Series · 2A · Series · 3

Replacement quarter-turn retaining clip for the rear tow-hitch cover.

Fits Range Rover Sport · L320

Flexible replacement overlay for worn key-fob buttons. Two versions are included: a partial overlay and a full button-hole overlay. Print in a flexible material with a fine nozzle.

Fits Range Rover Sport · L320

Replacement end cap for the passenger roof grab handle, measured from a 2000 four-door vehicle.

Fits Freelander · 1

Replacement air intake for a Webasto Thermo Top V fuel-burning heater when the original retaining legs have broken. Print with the legs downward and supports from the build plate.

Fits Discovery · 3 · Discovery · 4 · Range Rover Sport · L320

Replacement socket clip for the headlight adjuster. Two screws secure the clip to the lamp and the socket snaps onto the adjuster ball

Fits Discovery · 1

Replacement push clip for the front cowl and wiper-panel cover on 2002–2009 vehicles. Use a flexible, weather-resistant material and compare dimensions with an original clip before fitting.

Fits Range Rover · L322

Dashboard phone mount for fitting a Quad Lock interface in the Discovery 3/LR3 cabin. Confirm the mating interface and dashboard fit before final installation.

Fits Discovery · 3

Repair clip for a broken rear-seat latch, supplied with a trim-removal tool. Reuses the original spring

Fits Discovery · 3 · Discovery · 4

This a double fuel pipe clip for Td5 defenders, to hold fuel hoses to the chassis.

Fits Defender · Td5

Finishing fascia for an Android two-DIN radio in the 159. The creator gives an 11.5 × 19.2 cm radio size, a 13 × 20.2 cm dashboard opening, and printed it in black PETG.

Fits 159 · Tipo 939

Adapter for mounting a standard tweeter on the original 145 tweeter mount. The creator glued the tweeter to the adapter and removed the front grille and bent the tweeter wire pins to fit the available space.

Fits 145 / 146 · 145 / 146 (Tipo 930)

Can holder sized for a 0.5-litre, 67 mm can and designed for the 159.

Fits 159 · Tipo 939

Two-part replacement sun-visor retaining clip. The creator recommends printing the base on its side for strength and using ABS because PLA may fail at cabin temperatures.

Fits 156 · Tipo 932