Every printable part.

A little tool I printed to turn those pesky panel locks on my BMW E90 without instead of marring the edges with a big screwdriver. Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

The dashboard panel around the start button in my e92 began falling off due to a failed clip. I left it like this for quite awhile then the passenger door wood panel also fell off so I decided to design both clips to replace the broken ones as they cost more money than im willing to pay for original and aem ones dont last one use. I printed them with support on their sides so the opening is going up and down as this doesnt rely on layer adhesion for strength. "dash clip 1" is the dash clip "clip 3" is the door clip Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

This is a cover to replace the 12v point in the boot/trunk of an E91 ( check for other models similar) with a blank plate. For fitment insert widest plastic tap to top and tap/hammer upwards. Then support the plastic of car from behind and push/hammer in. Push down to seat and stop it falling out. Cleaning up of carpet and plastic edge of hole may be required. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Adapter for side led blinker - bmw e90 Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal and verify unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Hello, does your sunroof deflector make a weird noise or doesn't allow your sunroof to close sometimes. Well a section of it may be broken. Both of the side stoppers on my deflector were broken so i printed a replacement pieces. Supports are needed, i used roof support as well. Replacement part for OEM BMW handle. Part Number: 54107157449 Supersession(s): 54-10-7-157-449 This product fits 60 vehicle variants. BMW: 11 models, 60 variants between 2004 and 2012. BMW E90 Slipstream Deflector Replacement Clips/Stoppers 2004-2012 by blackjet123 is licensed under CC BY-NC-SA 4.0 CC Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Hello, since the OEM handle was so expensive i decided to create my own. Let me know what you think. Supports are needed, i used roof support as well. WARNING be careful removing the supports you can break the top sections. Replacement part for OEM BMW handle. Part Number: 51477152356. Supersession(s): 51-47-7-152-356 (This product fits 123 vehicle variants. BMW: 12 models, 123 variants between 2004 and 2013.) BMW E90 Trunk Handle Replacement 2004-2013 by blackjet123 is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. First Thingiverse make! Let me know if i missed any useful information. Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

This is a nice update for us with older E90 BMW's This will allow you to mount a universal Inbay wireless charger. This seems to work well and looks like a factory addition. It will take place of the front pocket in the console or the ashtray if it was equipped. This bracket will mount directly inplace of the old insert. Powering up the device: I did not have the ashtray so I was able to wire this into the power of the usb in th back of the console. you can access this easily by removing the rear vent panel. you can also pull out the plastic rear vent tubing with a little force to more room. You will tap into the Brown/ Ground and the Red/ +12V going to the usb in the rear console. LED Light: As an option I have added some holes for the LED light on the side of the charger. you will need to source a thin fiber optic cable and use the included plastic insert to fit the bigger hole. you wi Use automotive-rated wiring and connectors, retain fuse protection, insulate every terminal and verify unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

REPLACEMENT TRAY FOR USELESS PHONE CADDY watch this to learn how to remove that useless thing NOT MINE VIDEO ALL THE CREDIT TO THAT GENTLEMAN And then replace it wit the tray enjoy Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Can be installed in preexisting holes, no drilling necessary. BOM: 2 x M4x10 screws 1 x M4x50 screw 3 x M4 nuts Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

So I was looking for a fitting cupholder for my BMW E90 tray and couldn't find one which wasn't too big. This one fits to your BMW E90 without the big navi and without the iDrive knob. I made 3 versions which can fit 250ml, 330ml or 500ml cans (Germany/EU). With the big one, the walls might get too thin, read below. It fits very good to the tray, I use it everyday. This was designed to be printed with PLA, if you use ABS you might upscale it. Also, you can print it on the flat surface with my tag without supports. If you like the design, leave a tip :) *** Update 27.06.20 Someone requested a wider hole (currently 57mm) for norwegian 500ml cans. Uploaded another version with 66mm. Walls get very thin and cut, NO guarantee for good results as I won't try it! *** Update 11.07.20 Was shopping a german/EU 330ml can and couldn't fit it. So I made the hole slightly wider (59mm) to fit these. Ha Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

BMW Toolkit screwdriver. I designed this for E90 toolkit, as they stopped supplying these in the trunk after E46's. I spent ~$10 for a Phillips/flathead screwdriver from an online OEM supplier. This vehicle uses solely Torx fasteners, so a Phillips/flathead does me no good. This design allows you to use an off the shelf 2" long 1/4" bit extender. Then you can add whatever bit you'd like. Such as any size Torx bit, any size Phillips, or a flathead. It doesn't quite fit in the toolkit, some trimming would be required as the extender is thicker than the stock neck. However it will fit nicely, and the trimming is easy. The extender is a friction fit, but using an 0.2[mm] nozzle, it is TIGHT. It is also worth noting that this screwdriver has a 10mm box wrench on the bottom, and an 8mm box wrench on the top, but you have to remove the extender to use that one. Replaces BMW PN 71111179629 Shoul Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

This is a fix that I made for my 2007 BMW 320D air intake back in 2014. The M47N2 engine air intake hose has rubber ends which start to break over time, so instead of spending >30€ on a new OEM part (13717795284), I decided to make a fix of my own, as I had a 3D printer at home at that time. People keep asking me for the STL, and since I no longer have my own server, I decided that it's time to upload it here. NOTE: it's a tight fit so you'll most likely have to remove the whole 3 connecting parts of the intake as a single unit when trying to get to the engine (only 4 screws though, so it's not a big deal). Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Can holder designed for 55 mm Red Bull cans. It is only suitable for cars without iDrive because it occupies the center-console location normally used by the iDrive controller. The creator reports a print time of 12 hours 3 minutes and dimensions of 74.8 × 135.1 × 72.4 mm. Use cabin-heat-resistant material, dry-fit the part, and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

hi this is my custum made for led back cover lights bmw e90 318i valeo lci ligts please use support my paypal is: sezgin9716@hotmail.com thanks :) Confirm body and lamp variant, secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E90 / E91 / E92 / E93

In my BMW E91 were the Air Vent Levers missing. The original replacements cost a fortune, so i designed some by myself. Print them with PETG or similar. I recommend to print the fork with hinge part. Use the Fork and the Lock File only if you want to print them separately. For the stripe you may want to change the color, so i made it one part for manual color change by a certain height and two parts for MMU printing. You should add a raft under the Leverpart for better bed adhesion on the very small parts lying on the bed. Print them in the provided orientation Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

OBD2-Cover for BMW e90/e91 Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

Clutch alignment tool for BMW E90 - engine type n47tu - place some tape around the spindle on the tool to make a firm fitting. Custom designed in TinkerCAD, whipped it up in about 15 minutes after googling the dimensions and worked great!!! Originally bought a kit with multiple sizes of spindle and none of the sizes supplied fitted, so, 3D printed this instead and worked better than spending £25 at my local auto-parts dealer for the kit!! Use the tool only for the documented engine or transmission, keep it square and follow the BMW service procedure and torque values.

Fits 3 Series · E90 / E91 / E92 / E93

Seat belt hook attachment for BMW E92. Simply attach with a high quality double sided tape. Confirm normal seat, belt and presenter movement and keep the printed part outside the restraint load path.

Fits 3 Series · E90 / E91 / E92 / E93

Shift knob designed for e90 but may fit others. Clips on and does not rotate (careful of breakage if you try to twist it!) Fits fine, but is a bit light. Would be a nice print in transparent colors. Difficult to remove without breaking the teeth! (the knob teeth not yours) Please share your makes :) Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

The is a model of a BMW E90 plastic nut. These nuts are used in the undertray, splashguard and several other places in the vehicle. The nut itself is unthreaded since it is screwed onto a thread cutting fastener. The inner diameter of the nut is 4.25mm. The nut fits a 10mm wrench. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

This is my first 3D design. I needed this to plug holes in my bumper without buying parking sensors. It fits nicely, although I used some epoxy glue to be sure it stays in. Use exterior-rated material and verify secure retention and adjacent-panel clearance.

Fits 3 Series · E90 / E91 / E92 / E93

The cup holders in my 325i are small and work with anything bigger then a 12oz can. I designed this cup holder fit large insulated tumblers like the Yeti. The top 2 pieces need to be glued together. Gorilla glue works well, but any plastic glue should work. I used a hot glue gun to secure the base to the center console of the car. The hot glue works well and can be removed without any damage to your car. Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93

When I bought my e91 it had no front console cigarette lighter which meant I had to use an after market accessory plugged into the armrest socket. The unit was then wedged between the console and the passenger seat. Less than ideal. This plate fits in the ashtray hole and has a cut-out to accept an after market twin socket adapter which can be commonly found online or in value stores. I desinged this in sketchup and have included the SKP file in case anyone would like to remix it. Happy Printing Use cabin-heat-resistant material, dry-fit the part and verify secure retention and unobstructed operation.

Fits 3 Series · E90 / E91 / E92 / E93