Every printable part.

Filament: ASA Supports: Yes (As Applicable) Infill: Minimum 15% Brim: Yes (As Applicable) Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Do NOT print it in PLA, it will deform/melt. Printed with supports. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Front-door reduction adapter physically used in an E46 325Ci Coupe to install a 5.25-inch Kicker speaker in the factory 6.5-inch position. The source shows the printed ring, driver assembly and door fitment. Use sealing foam as documented and verify cone, magnet, wiring, window and door-trim clearance before fastening.

Fits 3 Series · E46

Print these to fix the broken boot handle on your BMW. Theyre designed so they squeeze in the holes, creating some tension to be able to screw the handle to the car. The “center” ones are for the 2 center bolts, the “side” ones for the outer ones. Fits nice and neat on my 2003 e46 Touring, may need some slight adjusting but worked well enough for me. Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

This bracket allows to mount the Pioneer GM-D1004 amp in place of the factory amp in the trunk. I used PETG and it works fine. Put some automotive Tesa tape on the metal ears before sliding the bracket to dampen vibrations. If You are missing a mounting screw or nut here are the codes: 07119902932, 61131372033. Fuse and insulate any added wiring correctly, secure it from chafe and confirm the circuit remains serviceable.

Fits 3 Series · E46

When I bought some roof rails, the flaps for the screws to not scratch the paint had been broken off. So I threw this quick redesign together. It's mostly a replica with slight adjustments for better printing. DO NOT USE PLA, PETG, OR ABS You should consider a high-quality, very weather and outdoor-resistant filament. I used CPE CF112. Alternatives may include PA CF12 or PP. Print slow. Low to no fan. The chamber should be at least 40°C for best layer adhesion. Works best with 100% infill. Sadly I could not find the specific part number for this, I've heard a simple washer should do just as well. However, I'd like to keep it as original as possible with this, as it also helps with alignment. Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Five-piece adapter set for 165 mm midrange speakers and 44 mm tweeters in Euro-spec E46 Coupe and Convertible doors without factory Hi-Fi or Harman Kardon. The creator documents the original mounts, printed adapters, driver assembly and installed sound-deadened doors. Verify speaker, wiring, window and door-trim clearance before fastening.

Fits 3 Series · E46

Print a cheap replacement for OEM E46 sun visor clips. I recommend printing at 100% infill to prevent splitting at layers when installed. I had good success with a 98A TPU filament at 100% infill with supports on. Just give extra support spacing with TPU and use a torch after to lightly clean up any strings. Wouldn't recommend PLA due to the high temperature that the inside of vehicles can see during the summer heat. Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Front-door adapter for installing a 165 mm speaker in the E46 Compact, whose factory speaker differs from other E46 bodies. The creator documents the original door, factory speaker, printed adapter and finished installation. Dry-fit before fastening and verify glass, wiring, cone and door-trim clearance through full window travel.

Fits 3 Series · E46

Sixteen-flat 86 mm service wrench for the oil-filter housing on E46 models with the N42B18A engine, designed for a 12.5 mm square drive. The creator shows the physical tool on a ratchet. Use a strong heat-resistant material, keep the wrench fully seated and follow the BMW service torque for the housing cap.

Fits 3 Series · E46

So I broke my wiper clip while replacing some other stuff on the car. There's not really a viable/economical replacement and original part does not take well to super glue. I started from another STL and modeled over it in fusion. Then did a couple of test prints and iterated as I went. Depending on your tolerances, filament, and shrinkage, you may have to fiddle with the final dimensions. Printed in PC-ABS. It doesn't fall off when using the windshield washing function. idk if I'd use it in a rally race. Use at your own risk. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

Isofix cover for BMW E46 I was missing one of the isofix covers so I modeled and printed this one. It's not a perfect copy since I added a bit of thickness in some parts to make it stronger. You can see in one of the images the differences between the original and the 3d printed part. For this one the ABS filament is required since the PETG & PLA are not rigid enough. Added a magnetic version, magnet can be glued in place, 20 x 10 x 3 mm magnet size. This alleviates the need to print the part in ABS for strength. Print Settings Printer: TwoTrees Bluer Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Filament: Generic ABS Black Notes: Category: Automotive Confirm seat movement, belt access and occupant clearance before use.

Fits 3 Series · E46

This is a nut for the engine cover as seen in the second image. It works for e46 316i,318i and 320i, possibly for other models that have the same nut. Note: you will need an O-ring or rubber washer (⌀10mm) to prevent unscrewing due to the engine vibrations, the original nut has one too. You'll need ABS filament or PET-G, PLA filament will break after a couple of months. Print Settings Printer Brand: Artillery Printer: Artillery Hornet Rafts: Yes Supports: No Resolution: 0.2 Infill: 25 Filament: ABS or PET-G Notes: minimum 3 perimeter for Vertical shells Category: Automotive Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

Seals for the BMW E46 320i Touring for the roof rails. Print settings: Material: Filaflex Semisoft Supports: No Layer height: .3 Infill: 40% Use exterior-rated material and verify secure retention, sealing and adjacent-panel clearance.

Fits 3 Series · E46

Cut off the remains of the rubber part on your windshield cowl and attach these printed ones. OEM PART: 51718208483 Mirror the end part to use it on the other side. Print multiple mid parts to cover the entire length. Printed from Fillamentum Flexfill 89A. Using 0.15mm layer height is important as there is a steep overhang on the part, which wouldn't print well using thicker layers. The end part might not fit perfectly but it did the job already so I didn't tweak it anymore. Use heat-, UV- and fluid-resistant material and verify full wiper or washer clearance.

Fits 3 Series · E46

This is a remixed version of the original thing posted here on Thingiverse, which is a shift boot bracket for the BMW E46 3 Series. It has better strength as with the added fillets and the clips are thickened as well as enlarged for better fitment. It will fit both RHD and LHD BMW E46 and will provide tight fitment. If you are planning to install with thick Alcantara leather boot, then it will be wise to scale it down a bit to 96-97% scale but if you are just planning to use faux leather boot, then at 100% scale it will be just fine. Use custom support blockers to increase the infill density of the clips to 99% for added strength. Print it in ABS or PETG because PLA will definitely deform du Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Replacement air-intake suction tube for 1999-2001 E46 M52 models, physically installed by the creator. BMWFans, RealOEM and Hubauer cross-confirm genuine BMW component 13711438768 for the matching E46 320i/320Ci, 323i/323Ci and 328i/328Ci applications. Print in a heat-resistant engine-bay material and verify sealing and clearance.

Fits 3 Series · E46

My dog rides shotgun and would always step on the hazard button when getting in and out, or when I left him in the car. I made this button cover to prevent paws from being able to activate the buttons, but still allow a finger to hit them easily. This is a friction fit in my car and doesn't move around at all. I sanded the top surface in the main picture. source openscad file is attached. Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Rafts: No Supports: No Resolution: 0.2mm layer height Infill: 20% Notes: printed upside down Post-Printing I sanded the top surface to make it a matte finish so it doesn't stick out in the car. Category: Automotive Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

Four-piece repair for the broken mounting tab on the pre-facelift E46 tail-light bulb holder. The creator physically tested it on a 1999 E46 320i with amber turn signals and documents the M6/M3 hardware and left/right external plates. Confirm body and lamp variant, secure every fastener, and verify weather sealing and legal lamp operation.

Fits 3 Series · E46

This is for installing a new center support bearing on your E46 driveshaft without risking damaging the bearing. Simply apply some lubricant where the bearing will seat onto the driveshaft and slide bearing on. Then use the tool to hammer in the bearing. It is easier to do with 2 people or if you can stand up and balance the driveshaft with your legs (Ask me how I know). Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

I used this tool to remove the crankshaft seal on the M54 engine timing cover. To use it properly, you must place the removal tool from the inside of the timing cover, pushing the seal out towards the outside of the timing cover. Use a mallet and some patience to get it out. Use the specified automotive-grade material, keep the tool square and inspect the serviced component before reassembly.

Fits 3 Series · E46

replacement interior hood latch, original often breaks this version is way stronger than the original Use cabin-heat-resistant material, dry-fit the part and confirm secure retention and unobstructed operation.

Fits 3 Series · E46

BMW E46 Headlight washer cap (left side) BMW part number: 6167.8.256.179 Verify secure retention, weather sealing and legal lamp operation before driving.

Fits 3 Series · E46

These clips can be glued in your oval mirror housing of a BMW E39 M5 or E46 M3 to repair the broken ones. Use "crazyglue" and line the clips up with the missing tabs in the housing. See photos for reference. Dry-fit before fastening and verify glass, latch, wiring and trim clearance through full operation.

Fits 3 Series · E46 · 5 Series · E39