Every printable part.

Charging dock shaped for the front centre-console cupholder and an iPhone 12 in an Elago silicone case. The creator states exact Vito fitment, recommends ABS or PETG because cabin temperatures can exceed 70 °C, and notes that other cases, phones and cable plugs require geometry changes. Match the cupholder, phone case and charging connector, route the cable without pinching it, use supports as specified, and verify the dock and phone stay retained without obstructing the selector or controls.

Fits Vito / Viano / V-Class · W447

Cosmetic plug for closing the exposed holes left after removing the armrests from individual V-Class seats. The creator explicitly tags this chassis and supplies the printable child geometry and multiple CAD source views, but gives no material, seat-version, colour or long-term retention details. PETG, ABS and nylon are listed only as conservative tough cabin-heat-resistant choices. Compare the exposed seat hole and plug profile, fit without forcing the seat trim, and confirm the plug remains secure and does not interfere with seat adjustment or restraint hardware.

Fits Vito / Viano / V-Class · W447

Two-piece holder that slides over the central Audio 20 display and carries a 12.9-inch second-generation iPad Pro in its leather case. The creator explicitly designed it for the V-Class/Vito/Marco Polo display in this chassis and instructs bonding the two printed pieces after printing. The source gives no material; PETG, ABS and nylon are listed only as conservative cabin-heat-resistant choices. Match the Audio 20 display and tablet/case dimensions, line the vehicle-display interface with textile tape as shown on the same-author follow-up, and verify the holder cannot obscure the road, controls or airbags or release the tablet under braking.

Fits Vito / Viano / V-Class · W447

Two-level center-armrest organizer source-backed for 2015–2021 C-Class interiors and the corresponding GLC console. The upper tray includes Canadian coin slots, a phone compartment and general storage; the lower tray catches loose items. Source imagery is CAD and slicer evidence only. Verify the 258×123×65 mm envelope before printing, ensure the lid closes freely, and do not place items where they can jam the console or controls.

Fits C-Class · W205 / S205 / C205 / A205 · GLK / GLC · X253 / C253

Multi-part Gridfinity-based replacement for the center-console cupholder and storage unit, explicitly stated by the creator to fit V-Class/Vito, C-Class, E-Class sedan/estate/coupé/cabriolet applications sharing the original insert. It reuses the original double-torsion spring, adds supported cupholder clips, and uses 6×2 mm magnets. Preserve spring orientation, secure every magnet, verify each module locks in place, and keep all contents and moving parts clear of controls. The creator identifies the exact replaced cupholder unit as A2056800691, corroborated by the official Mercedes-Benz genuine-parts listing.

Fits C-Class · W205 / S205 / C205 / A205 · E-Class · W213 / S213 / C238 / A238 · Vito / Viano / V-Class · W447

Drop-in center-console insert developed in a 2015 C450T, with separate versions that either include or omit a phone pocket. The creator states that it provides two bottle or can recesses and requires no tools or vehicle modification. Use the version appropriate to the carried items, verify full seating and console-lid clearance, and confirm bottles and the optional phone remain retained during driving.

Fits C-Class · W205 / S205 / C205 / A205

Three-part magnetic phone-mount system whose base clamps between the display and instrument cluster. The source specifies 6×4 mm and/or 10×3 mm magnet pockets and shows the physical components and installed fit. Confirm magnet polarity and secure encapsulation, use the correct nut and ball adapter, protect trim, and verify the phone cannot obscure the cluster, detach, or interfere with controls.

Fits C-Class · W205 / S205 / C205 / A205

Cup-shaped storage inserts for the shared C-Class, E-Class, and GLC cupholder geometry, supplied with and without a light window and with optional coin storage. Only the non-ashtray files are included; the ember-extinguisher variants are intentionally withheld. The creator used flame-retardant ABS. Select the correct lighting version, keep the original light unobstructed, and use only for coins or other small non-hot items.

Fits C-Class · W205 / S205 / C205 / A205 · E-Class · W213 / S213 / C238 / A238 · GLK / GLC · X253 / C253

iPhone 8 holder explicitly designed for C-Class and GLC interiors equipped with option code 522 Audio 20 NTG5 and the small display. It is installed with double-sided tape and the source routes the charging cable beneath the center console. Fitment is limited to that display option; clean the bonding surface, use automotive-grade tape, strain-relieve the cable, and verify the holder cannot obscure instruments or detach.

Fits C-Class · W205 / S205 / C205 / A205 · GLK / GLC · X253 / C253

Charging dock sized for an iPhone 13 Pro in a Rhinoshield case and designed for the center-console cupholder. The creator notes that other cases, phones, and cable plugs require geometry changes, recommends ABS or PETG because cabin temperatures can exceed 70 °C, and provides both STL and STEP source files. Verify exact phone and plug retention, strain-relieve the cable, and keep the dock clear of controls.

Fits C-Class · W205 / S205 / C205 / A205

Two-part MagSafe-charger stand made to replace the ashtray insert and tested by the creator in the C-Class console. Source images show the physical print and installed charging position. Use cabin-heat-resistant material, verify the charger is securely retained and ventilated, route the cable without pinching it, preserve lid and control movement, and do not use the assembly as an ashtray.

Fits C-Class · W205 / S205 / C205 / A205

Two cupholder inserts sized for 250 ml and 355 ml energy-drink cans. The creator explicitly states fitment across the sedan, estate, coupé, and cabriolet body variants and provides physical in-console images. Use a heat-resistant interior material, confirm the chosen insert seats fully, keep liquids clear of electrical controls, and stop use if the can can tip, bind, or interfere with the console lid.

Fits C-Class · W205 / S205 / C205 / A205

Work-in-progress umbrella holder for the C300 trunk, source-backed for model year 2015 onward and attached through existing factory holes with 1/4-20 by 1-inch bolts. Source images show both the physical brackets and their installed position. Use only for a light umbrella, preserve access to adjacent equipment, verify fastener engagement and trunk-lid clearance, and never use the printed brackets for cargo restraint or any safety-critical load.

Fits C-Class · W205 / S205 / C205 / A205

Screen-hook phone-mount bar with a 14 mm ball, designed around an MPOW wireless charger. The author supplies separate right-hand-drive and mirrored left-hand-drive files and shows both the bare part and installed phone. Bend only as required for installation behind the screen, verify the correct steering-side file, protect dashboard surfaces, and confirm the mount cannot obscure instruments, loosen, or contact controls.

Fits C-Class · W205 / S205 / C205 / A205

Four-file tray system for an Anker PowerWave Pad in the center compartment. The source shows the tray fitted with the compartment opening and closing and includes revised V2 geometry that moves the charger 15 mm for smaller phones. Select the matching base and cover pair, use cabin-heat-resistant material, route the cable without pinching it, and confirm the phone, tray, lid, selector, and adjacent controls remain secure and unobstructed.

Fits C-Class · W205 / S205 / C205 / A205

Two-file mounting set for 10.25-inch and 12.3-inch aftermarket Android head units. The creator states that it lowers the display for a more factory-like position and shows the assembly installed. Verify the screen and supplied hardware are compatible, retain full visibility of the road and instruments, prevent contact with vents or trim, secure all wiring, and recheck fasteners after installation.

Fits C-Class · W205 / S205 / C205 / A205

Center-console insert for a Spigen SteadiBoost Compact wireless charger. The creator explicitly developed and photographed it in the C-Class cabin, warns that parked-car temperatures can reach 70–90 °C, and recommends ABS instead of PLA where possible. Route and strain-relieve the power cable, preserve console-lid and control clearance, confirm the phone remains retained during driving, and stop use if heat deformation occurs.

Fits C-Class · W205 / S205 / C205 / A205

Cupholder-mounted cradle made for a Sony Xperia XZ2 in a protective PU case and test-fitted by the creator in a C350e. The vehicle must have the removable factory cupholder option. Confirm the cradle is snug without overstressing the cupholder, keep the phone and cable clear of the selector and controls, and remove it if the print softens, cracks, or permits the phone to move.

Fits C-Class · W205 / S205 / C205 / A205

Two alternative phone-holder files designed to sit in the middle-console compartment for A180 and A200 variants. The creator states compatibility with iPhone and Android devices, simple installation, and support-free printing; source photos show the holder installed with a phone and charging cable. Choose one alternative file, verify a stable fit with the specific phone and case, use a cabin-heat-resistant material, and keep the device and cable clear of the selector and other controls.

Fits A-Class · W176

Small service adapter for more easily loosening and tightening the rear-lamp retaining fastener during bulb replacement. The creator specifies PETG plus an M5 heat-set insert, an M5×6 socket-head screw, and a DIN 9021 5.3×15 washer, and source photos show the assembled tool on the fastener. Use it only as a hand tool; do not overtighten the lamp fastener, and inspect the printed body and insert before each use.

Fits A-Class · W176

Simple insert that holds an Ooono traffic-alert device in the center-console ashtray. The creator identifies exact hatchback fitment; no steering-side, console-option, or facelift extension is stated. Confirm the ashtray dimensions before printing, use a cabin-temperature-capable material, ensure the device cannot become loose, and keep it clear of the selector and all driving controls.

Fits A-Class · W176

Phone holder designed to fit beside the dashboard display. The author supplies a base holder and phone-specific variants for iPhone 11, iPhone 8 Plus, and the 2016 iPhone SE, and shows a physical holder fitted in the vehicle. The creator used heat-resistant Extrudr GreenTEC rather than ordinary PLA, which can soften in a hot cabin. Choose only the matching variant, confirm secure retention, and keep the device clear of the driver’s view, controls, airbags, and ventilation.

Fits A-Class · W176

Phone-mount adapter designed for the two center dashboard vents and used by the creator with a uGreen magnetic mount. The source identifies exact hatchback fitment and provides the printable adapter; the mating phone mount is not included. Print in ABS as specified by the creator, verify that the adapter does not crack or loosen, maintain airflow, and position the phone so it cannot obstruct the road view, controls, display, or airbags. The source GNU GPL v2 licence is represented by the API’s other licence value.

Fits A-Class · W176

Removable bottle-holder insert designed from the center-console compartment in a 2017 hatchback. The creator states that the original center divider must be removed and that the two holes allow the insert to be lifted out for cleaning. Fitment evidence is limited to the 2017 example; no steering-side, trim, or facelift extension is inferred. Use a cabin-heat-resistant material, verify that bottles remain stable, and remove the insert if it interferes with nearby controls.

Fits A-Class · W176