Every printable part.

Two-file custom rack system made to fit the center-console ashtray opening in an SLC 180. The author description explicitly identifies the R172 ashtray and provides a fitted remote-control rack plus a starter frame that can be extended for other small controls. Source fitment is limited to the SLC 180 facelift variant; no pre-facelift SLK fitment is claimed. Use a cabin-temperature-capable material, verify the insert is fully seated, keep controls and loose objects clear of the selector and roof controls, and remove the rack if it can move or obstruct driving controls.

Fits SLK / SLC · R172

Single-piece cargo lashing ring designed for the roadster trunk and fixed beneath an existing trunk screw. The creator explicitly identifies R172 fitment and shows the ring installed. It is only for restraining small, light items while driving; the creator states that it is not made for high forces. Do not use it for heavy cargo, occupant restraint, recovery, lifting, towing, or any safety-critical load. Confirm that the original fastener retains full thread engagement, keep the ring clear of roof and trunk mechanisms, and remove it if the print cracks, loosens, or deforms.

Fits SLK / SLC · R172

Clip-on folding sun-visor extension designed and physically shown on W212 and S212 driver and passenger visors while retaining access to the illuminated mirrors. The creator supplies separate left/right brackets and a 330 mm panel and requires ABS or ASA because PLA and PETG deform in summer cabin heat. Match the visor and seating position, use the specified high-temperature material, and verify the panel locks securely, folds clear, preserves required road visibility and cannot interfere with airbags.

Fits E-Class · W212 / S212 / C207 / A207

Support-free MagSafe charging mount designed for a W212 E350 across the creator-stated 2009–2016 span and physically shown on top of the centre-console ashtray. It is designed around the linked charging puck, 65 W socket adapter and 70 mm cable; other pucks are untested. Match all electrical and console dimensions, use cabin-heat-resistant material, strain-relieve the cable, avoid trapping heat, and verify the phone and mount remain secure without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Solid and through-hole accessory-mount bases remixed from a W212 cupholder phone-rest geometry and physically shown carrying a suction-mounted display. The author recommends PETG or stronger infill rather than the PLA lightning-infill prototype. Match the cupholder and accessory footprint, use cabin-heat-resistant material and suitable adhesive, and prove the mounted device cannot obscure controls, airbags or the road, overload the cupholder, or detach under braking.

Fits E-Class · W212 / S212 / C207 / A207

FDM-optimised replacement for the plastic female half of a trunk-well lid hinge, measured for a 2012 W212. The supplied file is right-hand; the creator instructs mirroring it for the left, printing in PETG with six walls and 25% gyroid infill, and orienting it at 45 degrees for strength. Match the original hinge and lid load, keep the hinge free of wiring and trim, and confirm the service lid opens, closes and remains supported before loading the trunk.

Fits E-Class · W212 / S212 / C207 / A207

One-piece centre-console insert published specifically for W212 fitment with a 90×78 mm storage compartment and a 66 mm circular recess for European 0.5 L cans. The source shows the printed insert installed but does not state body style, steering side or container-retention testing. Measure the console and container, use cabin-heat-resistant material, and confirm the insert seats fully, keeps a closed cool can stable and cannot obstruct the selector or controls.

Fits E-Class · W212 / S212 / C207 / A207

Phone holder designed for the PCMCIA slot in a 2010 C207 E500 coupe and around the creator’s phone with a Spigen card case, then printed in PETG. No other head-unit revision, phone or body style is established. Match the slot, card mechanism, phone and case dimensions; insert without forcing the electronics, and verify the mount cannot obscure controls, airbags or the road or eject the phone under braking.

Fits E-Class · W212 / S212 / C207 / A207

Four-part repair for the breakable sunshade vent/handle assembly in a W212, described by the creator as installed and tested in their car. The top and bottom handle pieces are joined with M2 screws; the creator later found the lower vent piece alone easier to install and recommends a higher-temperature material despite successful PLA use. Compare the broken assembly, use cabin-heat-resistant material, avoid over-tightening screws, and verify free shade and vent movement.

Fits E-Class · W212 / S212 / C207 / A207

Author-designed centre-console insert for W212 cars, physically shown in use with cups and a phone. The source supplies variants for 14 mm, 20 mm and 84 mm-wide phone cases plus can-stabilising rings, coin and card storage, specifies 24×3.5 mm felt pads for retention, and warns not to use PLA in summer cabin heat. Select only the matching variant, use heat-resistant material, fit the felt pads, and verify containers, cards and phone remain secure without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Cupholder-mounted phone rest designed for pre-facelift 2010–2011 W212 E350 sedans. The author shows the physical print with the original cupholder and states that its open centre permits a charging cable while the factory cover can still close. Print in ABS or another proven cabin-heat-resistant material, match the cupholder and phone dimensions, route the cable clear of controls, and verify the rest cannot release the phone or interfere with the selector under braking.

Fits E-Class · W212 / S212 / C207 / A207

Bottle and small-can inserts for the factory option-code 309 cupholder used in stated W212 and S212 cars with 7G-TRONIC-PLUS or 9G-TRONIC transmissions. The selected author files fit a 0.5 L beverage bottle and a 250 ml slim can; the unrelated vape-holder variant is deliberately not distributed. Match factory cupholder A 212 680 01 10 and the container dimensions, use cabin-heat-resistant material, and verify each insert and closed beverage remain retained without obstructing controls.

Fits E-Class · W212 / S212 / C207 / A207

Replacement handle designed for a broken rear-seat sun-protection shade and explicitly tagged for the S212 estate. The creator states that the printed handle must be drilled to 2.5 mm for final fit; no sedan, coupe or cabriolet application is established. Compare the original handle and pivot, use tough UV- and cabin-heat-resistant material, drill carefully, and confirm smooth shade movement without stressing the shade fabric or mechanism.

Fits E-Class · W212 / S212 / C207 / A207

Three-file phone holder designed and physically shown in a W212 dashboard and explicitly stated for W212 sedan and C207 coupe fitment. The main geometry fits an iPhone XR; an adapter fits an iPhone 6S, and the creator recommends a 2 mm metal reinforcing rod plus a separately printed rubber pad for hot-cabin durability. Match the phone and dashboard interface, use heat-resistant material, assemble every piece securely, and verify the holder cannot obscure controls, airbags or the road or release the phone under braking.

Fits E-Class · W212 / S212 / C207 / A207

Trunk-floor tray designed specifically for the left-side storage recess of the W212 sedan and for a 17 mm wheel-nut impact socket plus a stated 28018SL wheel-lock key. The creator supplies the exact intended tools but does not state body-style alternatives or road testing. Compare the recess and tool dimensions, use tough cabin-heat-resistant material, and confirm both tools remain fully captured and cannot rattle loose or become projectiles.

Fits E-Class · W212 / S212 / C207 / A207

Two-piece hook designed for the existing oval opening in the upper trunk sheet metal of the W212 sedan. The creator specifies two M4×10 mm countersunk screws and a sliding dead-bolt piece; the source identifies the installation position but does not show the hook installed or state a load rating. Use tough heat-resistant material, inspect the opening and sheet-metal edges, tighten both screws, and use only for light soft items after proving retention; never treat it as a cargo-restraint or safety anchor.

Fits E-Class · W212 / S212 / C207 / A207

One-piece holder designed specifically for the front-seat console of a 2014 C207 coupe. The creator states that other vehicles may fit but supplies no evidence for them. Match the console opening and container dimensions before printing, use cabin-heat-resistant material, and confirm that the holder cannot obstruct the selector or controls, spill into electronics, or release a container under braking.

Fits E-Class · W212 / S212 / C207 / A207

Snap-in plastic-panel mounting pin published for Mercedes GLK and C-Class vehicles. The creator does not identify its panel position, body side, market, model year, original part number, material or test history. Compare the removed fastener, panel thickness, slot dimensions and installed clearance before printing; use a tough automotive-interior or exterior-grade material suitable for the actual location, and confirm the panel remains securely retained without damaging adjacent trim. Do not substitute this print for a structural, restraint or load-bearing fastener.

Fits GLK / GLC · X204

Five-file tablet-holder variants fitted over the original radio-display cover of a CDI 220, including a later version positioned lower and farther from the driver’s view. The creator designed around an 8-inch tablet and retained access to the original display. Match the dashboard cover, tablet and viewing position, use cabin-heat-resistant material, protect trim and wiring and verify the assembly cannot block the road, controls, airbags or ventilation or release the tablet under braking.

Fits C-Class · W204 / S204 / C204

Flexible replacement tether published specifically for this generation. The creator requires TPU and instructs removal of the lid pin and remaining old tether before fitting the new piece snugly around the fuel cap without affecting its seal. Compare the pin, cap eye, tether length and filler-lid clearance, use fuel-vapour-, UV- and weather-resistant TPU and confirm the tether cannot enter the filler neck or prevent the cap from sealing completely.

Fits C-Class · W204 / S204 / C204

Cup holder designed for a 2013 C180 and physically shown in its centre console, with short and long sleeves for 59 mm cans and larger containers. The creator recommends PETG or ABS for cabin heat, supports and roughly 0.16–0.24 mm layers. Match the console and container diameter, check selector and control clearance and use only closed, cool containers until retention is proven; verify the holder cannot loosen or cause a spill under braking.

Fits C-Class · W204 / S204 / C204

Cupholder insert designed and printed for charging a Huawei P30 Pro from an Anker PowerPort wireless charger while leaving the rear storage compartment available. The source shows the physical insert and phone in the vehicle and includes one selected STL plus the preserved editable author file. Match the cupholder, phone and charger dimensions, use cabin-heat-resistant material, protect and strain-relieve the power lead and confirm the phone and insert cannot obstruct the selector or controls or detach under braking.

Fits C-Class · W204 / S204 / C204

Compartmented insert designed for the door pocket across the stated 2007–2015 production span, with spaces for cards, a flashlight, tissues or a small shaver and pens. The source supplies one STL and one source CAD image but does not identify door side, body style or steering market. Measure the pocket and stored items, use tough cabin-heat-resistant material and confirm the insert seats fully without scratching trim, interfering with door operation or allowing hard objects to escape under braking.

Fits C-Class · W204 / S204 / C204

Combined navigation-display holder and Galaxy S20 Ultra case published for this generation and shown installed in the source vehicle. The creator links both recoverable remix sources and instructs printing the supplied geometry at 1% scale. Confirm that scaling produces the intended phone and dashboard-interface dimensions before printing, use cabin-heat-resistant material and verify that the mount cannot obstruct controls, airbags or the road or release the phone under braking.

Fits C-Class · W204 / S204 / C204