Every printable part.

Three-piece iPhone 7 holder designed specifically for the original CD slot and shown installed in the source vehicle; the creator notes a thick phone case and charging lead. Match the phone, case and head-unit slot, use cabin-heat-resistant material, insert without forcing the disc mechanism and route the cable clear of controls. Verify that the holder cannot obscure controls, airbags or the road or eject the phone under braking.

Fits C-Class · W204 / S204 / C204

Replacement retaining nut published specifically for this generation and supplied with a source CAD image. The creator does not state the underbody panel position, thread dimensions, engine, drivetrain, body style, material or test history. Compare the original nut, stud thread, panel thickness and installed clearance, use heat-, water-, salt- and impact-resistant material and confirm the underbody cover is fully retained after a road test; do not use this print for structural, suspension or lifting points.

Fits C-Class · W204 / S204 / C204

Phone mount published specifically for this generation and a Samsung Galaxy S5. The author supplies one printable model and a source CAD image but does not state the head-unit revision, mounting procedure, steering side or road testing. Match the device and dashboard interface before printing, use cabin-heat-resistant material and confirm the mount cannot damage trim, obstruct the display, controls, airbags or road view, or release the phone under braking.

Fits C-Class · W204 / S204 / C204

Internal joystick shaft for the COMAND controller, measured from a broken original and redesigned without its nut. The creator explicitly identifies C-Class W204 and E-Class W212 applications and specifies 0.1 mm layers and 100% infill; no other W212-generation body styles are stated. Compare the removed shaft and controller revision, use tough cabin-heat-resistant material, transfer and assemble the mechanism without damaging electronics and verify full rotary, tilt and press operation before driving.

Fits C-Class · W204 / S204 / C204 · E-Class · W212 / S212 / C207 / A207

Three-file stand for holding several stated box-mod device sizes in the centre-console cupholder. For this generation the creator instructs that the supplied disc be glued or screwed to the bottom of the stand and reports printing in PETG. Match the cupholder and device dimensions, use cabin-heat-resistant material, assemble the disc securely and confirm that the stand and device cannot obstruct the selector or controls, spill into sockets or become a projectile under braking.

Fits C-Class · W204 / S204 / C204

Two-piece floor-mat retaining clip published for this generation and shown on the physical carpet and anchor. The creator warns that small scaling changes may be needed for a particular printer and recommends checking the top and bottom separately so they snap securely without becoming inseparable. Compare the original anchor and mat opening, use tough cabin-heat-resistant material and confirm every mat remains flat, removable for service and completely clear of the accelerator, brake and clutch pedals.

Fits C-Class · W204 / S204 / C204

Snap-in phone mount designed and road-used in a 2011 vehicle with the Audio 50 APS navigation display cover. The creator states that it retains an iPhone 6 during acceleration, braking and cornering and allows charging, but the display cover cannot close while fitted. Match the Audio 50 APS cover and phone dimensions, use cabin-heat-resistant material, snap it in without forcing the cover and verify that the phone cannot obscure controls, airbags or the road or detach under braking.

Fits C-Class · W204 / S204 / C204

Replacement mounting bracket for the sun visor, explicitly titled for 2006–2018 vehicles. The source provides one printable mesh and one CAD source image but no side, cab, market or option-code split. Compare the original bracket and screw spacing before use, print in a tough cabin-heat-resistant material, retain suitable original fasteners, and verify the visor pivots and stays secured without obstructing the driver or detaching.

Fits Sprinter · W906

Replacement recess surrounding a cargo-floor lashing eye. The creator explicitly identifies 906-series fitment, shows the part installed around the original eye, and recommends PETG or ABS instead of PLA because the original recesses rust and replacements are costly. This print is a non-load-bearing surround only: retain the original metal eye and certified anchor hardware, inspect corrosion beneath it, preserve full anchor movement and clamping, and never transfer cargo load through the printed recess.

Fits Sprinter · W906

Press-fit dock for the lower centre-console storage shelf, with a large-phone slot and three pen holes. The creator identifies 906-series fitment and supplies both the OpenSCAD source and printable mesh plus an installed source photograph, but gives no body, market or steering-side expansion. Confirm the shelf profile and phone size before printing, use cabin-heat-resistant material, keep the device and charging cable clear of controls, and verify secure retention under braking.

Fits Sprinter · W906

Dashboard phone-mount adapter designed by the creator for the GL 450 X164 and shown physically installed between the two center vents. The supplied single STL has a 17 mm ball for a compatible phone cradle. The source does not state model year, pre- or post-facelift fitment, market, steering side, dashboard option, attachment method, material, print settings, device weight, or retention testing. Compare the center-vent surround before printing, use a cabin-heat-resistant material, protect the original trim, keep the mount clear of vents, controls and sight lines, and verify that the adapter and cradle remain secure under braking before road use. Do not place a device where it could interfere with an airbag.

Fits GL / GLS · X164

Custom dual cup holder designed by the creator for the 221-series S-Class and shown both loose and installed in the center console. The supplied single STL includes an S500 emblem and the creator notes that it can be printed in one color or with a multi-material system. The source does not state model year, wheelbase, facelift, steering side, console option, container diameter, material, print settings, or retention testing, so compare the console opening and surrounding controls before printing. Use cabin-heat-resistant material, protect the original trim, keep containers clear of the selector and switches, and verify that the holder and only cold, closed containers remain secure under braking before road use.

Fits S-Class · W221

Left- and right-hand caps that close the openings at the tops of the front-door B-pillar trims. The creator modeled substitutes from a deteriorating original on an ML350, recommends ABS, ASA or PETG rather than PLA for sun exposure, and advises a test fit with light filing if necessary plus a small amount of clear adhesive behind the cap. EPC evidence found complete left/right trim mouldings, not these printed child caps, so no parent assembly number is assigned.

Fits M-Class / GLE · W164

Centre-console panel that replaces the ashtray box and cigarette lighter to mount a small aftermarket Bluetooth/MP3/SD/USB module. The creator states fitment for the 2006–2009 W164 ML280, ML320 and related variants and shows the physical panel installed. The file contains no electronics: use cabin-heat-resistant material, secure the module, independently fuse and insulate any wiring, and confirm selector and control clearance.

Fits M-Class / GLE · W164

Two-piece repair for the right-hand locking pin/holder used when the retractable luggage-compartment cover is pulled across the cargo area. The creator designed it from the broken component on a 2006 vehicle and separated the base and holder because a one-piece print was too tight to install; clip in the base, then bond the holder to it. Mercedes EPC-style evidence identifies exact child A1648120201 as the right cargo-cover locking pin and maps that same component to W164 and X164. Verify side, colour/trim interface and retention before use.

Fits GL / GLS · X164 · M-Class / GLE · W164

Three-part retaining tether for the fuel cap, explicitly shown by the creator on an R171 and described as fitting many Mercedes fuel caps. The design comprises a cap ring, flexible cord, and eyelet. The source used ASA for the ring and hard Shore D56 TPU for the cord and eyelet, while noting that approximately Shore A95 TPU may also work. Install all three parts, verify the ring does not interfere with cap sealing or locking, keep the tether clear of the filler neck and hinge, and replace it if fuel exposure, heat, or repeated flexing causes cracks or loss of retention. No other generation is linked because the creator does not identify one and no exact child-component number was established.

Fits SLK / SLC · R171

Two-piece replacement housing for the starter cable connector on a 2006 SLK 350. The creator modeled it after the original housing crumbled, printed it successfully in ABS, and warns that its position under the exhaust manifold exposes it to substantial heat. Use both housing halves, print only in a suitable high-temperature electrical-insulating material, inspect the cable and terminal for heat or corrosion damage before installation, maintain factory routing and insulation clearances, and discontinue use immediately if the print softens, cracks, or allows terminal movement. Fitment is source-backed only for the stated 2006 SLK 350 within R171.

Fits SLK / SLC · R171

Three-file magnetic phone-mount body designed specifically to clip into the R171 center console without glue, drilling, or permanent vehicle modification. The source includes a one-piece model and a split base/top alternative; add a generic magnetic phone pad to the upper surface with adhesive. Creator photographs show the printed mount installed beside the selector in left-hand-drive vehicles. Use only the one-piece file or the two split files as a complete alternative, print in a cabin-temperature-capable material, confirm the mount cannot contact the selector or controls, route charging cables clear of moving controls, and remove it if it loosens or obstructs operation.

Fits SLK / SLC · R171

Six-piece bracket and spacer set for installing a Hikity 10.1-inch Android double-DIN head unit in a 2005 SLK 350 without drilling the vehicle. The creator replaced an Audio 20 unit, reports that installation was easy, and says the brackets will likely suit SLK 280 variants and the rest of the same R171 generation; no fitment outside R171 is claimed here. The large screen requires removal of the factory cupholders. Print in PETG, ABS, ASA, or another cabin-temperature-capable material rather than PLA, which the creator warns can soften in a hot car. Verify fastener engagement, wiring clearance, screen stability, and unobstructed access to the hazard and Airscarf control panel before driving.

Fits SLK / SLC · R171

Replacement hinge inserts for the power-window actuator switches, supplied as distinct driver- and passenger-side files because the locating pins are different sizes. The creator shows the printed parts with the original switch housing and secures each insert with double-sided tape on its back and bottom surfaces. Use a heat-resistant material, select the correct side, keep adhesive clear of contacts and moving surfaces, and confirm normal switch return and window operation before refitting the door controls.

Fits A-Class · W169

Replacement retaining clip/cover for the front door trim panel. The creator explicitly identifies both the A-Class application and exact child-component number A1697270014; independent genuine-parts listings corroborate it as the left/right front door-card trim clip also used on the B-Class W245, which is absent from the live taxonomy. Verify trim colour and socket geometry against the removed clip, press the panel home without forcing it, and replace the print if the panel is not held securely.

Fits A-Class · W169

Left- and right-hand side guides for the inner shade of the factory lamella sunroof. The creator explicitly describes these as the second-version guides from a 2009 vehicle; do not treat them as universal for other roof systems, years or guide revisions. The files are separate side variants. Compare the original guide profile and orientation before printing, use a heat-resistant low-friction material, test shade travel gently by hand, and discontinue use if the guide binds, sheds debris or interferes with roof movement.

Fits A-Class · W169

Direct-replacement manual seat adjustment handles supplied as separate left- and right-hand files. The creator designed them for a 2007 vehicle and identifies the right-hand component as original part A1699190661; Mercedes genuine-parts and PartSouq listings corroborate that number as the right-side seat-adjustment lever. The OEM number applies to the right-hand file only. Use a tough, heat-resistant material, compare the mounting socket and travel with an intact handle, and verify that the seat locks positively in every tested position before driving.

Fits A-Class · W169

Two-piece retaining clip for the driver's floor mat. The creator designed and tested it on a 2011 vehicle, states that the two halves permanently snap together through the mat, and notes that removal from the floor takes slightly more force than the original. The source print used PLA with a 0.4 mm nozzle, no raft and no supports; for sustained cabin heat, prefer an automotive-temperature-capable material. Confirm that both halves are fully locked, that the mat cannot slide toward the pedals, and stop using the print if it loosens or cracks.

Fits A-Class · W169